Kenmore Dishwasher 665.17792990 (66517792990, 665 17792990) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 8193646
The Actuator is an OEM part for Whirlpool dishwashers. This actuator is responsible for releasing detergent from the dispenser at the appropriate time during the wash cycle, ensuring effective cleaning of the dishes.
Causes of a bad detergent dispenser actuator can include electrical malfunctions, wear and tear from frequent use, or physical damage to the actuator mechanism.
Symptoms of a bad detergent dispenser actuator include:
- The detergent not dispensing during the wash cycle
- The dispenser door not opening
- Dishes not being cleaned properly due to no detergent release
- Error codes related to the dispenser
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Latch would not open consistently on detergent dispenser James G. • Waxhaw , NC • January 12, 2015
Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle.
Read more
More
$48.95
- Compare At:
-
$57.76
- You Save:
-
$8.81
Genuine Whirlpool part
By: Whirlpool
Part Number: 676458
Color: Gray. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For white order 675679. To attach these tine tips you will need to order the dishrack gray touch-up paintWP676455.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$27.25
- Compare At:
-
$32.43
- You Save:
-
$5.18
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302711
This pump outlet seal sits on the discharge side of the dishwasher pump to keep the outlet connection watertight. Replacing a worn seal helps stop leaks and keeps wash water contained during the cycle. What it does:
- Seals the joint at the pump outlet to prevent water leakage
- Helps maintain proper circulation by keeping the pump discharge airtight/watertight
- Common symptoms of failure include water under the unit, drips near the pump area, or a flattened/cracked/hardened old seal
What's included:
Install notes:
- Disconnect power and shut off the water supply before servicing
- Remove the toe-kick/lower access panel to reach the pump area; place a towel or pan to catch residual water
- Note seal orientation; clean mating surfaces before installing the new seal
- Seat the seal evenly; reassemble and run a short test to check for leaks
Do-It-Yourself Stories from Customers like You
Loud dishwasher producing dirty dishes Leon F. • Sylmar , CA • November 11, 2015
I nearly shelled out for a new Kitchenaid when I remembered APP and entered my model # just for fun. The interactive diagrams and install videos showed where all the parts "should" be, mine were badly disintegrated, so I replaced the damaged ones and swapped out all of the other easily accessible seals and bearings (also gave it a good and very disturbing cleaning). My parts surprisingly arrived next day and for about $40, the dishwasher is quiet and works like new again.
Read more
More
$24.95
- Compare At:
-
$29.94
- You Save:
-
$4.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10253040
This genuine OEM part is a refrigerator upper dishrack. The upper dishrack is the tray on which dishes are placed on the top shelf of a dishwasher. If the dishrack is no longer sliding on its tracks, or is not staying in place during the wash cycle, it might need to be replaced. Luckily this is a very simple repair.To replace the upper dishrack, simply pull out the old dish rack and lift it up out of its tracks. Once removed from the dishwasher, take the new dishrack and gently slide it into place. Make sure it is placed correctly and that it is running smoothly on its tracks.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.
Do-It-Yourself Stories from Customers like You
The upper rack of our dishwasher needed replacing Lenwood J. • Statesville , NC • June 07, 2014
Ordered the part from Appliance Parts Pros, it arrived about a week later and it was the correct part. I liked the cross reference and confirmation of the correct part that was available on the website before placing an order.
Read more
More
$242.21
- Compare At:
-
$285.81
- You Save:
-
$43.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
Leaking around dishwasher door previous repair missing parts Patrick R. • Peachtree City , GA • November 15, 2014
I ordered new seals from AppliancePartsPros.com. Finding the right seals was very easy, all based on model number of the appliance. While looking my unit over for other signs of wear, I noticed that a repair done by the prior homeowner to the lower wash arm was done improperly: a seal there was set protruding from the cover, the cover was missing screws, and the arm was missing the upper bushing. So I ordered a new seal, the missing screws, and both the top and bottom bushings (just to be...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268874
This lower spray arm assembly circulates wash water from the pump to clean dishes on the lower rack. The integrated shield helps direct water flow and protect the arm from debris, restoring consistent wash coverage.
- Distributes high-pressure water across the lower rack for effective cleaning
- Shield design helps prevent debris intrusion and improves spray pattern
- Common failure signs: poor lower-rack cleaning, noisy or restricted rotation, cracked or warped arm, clogged spray holes
- Also addresses leaking or splashing caused by a damaged or misaligned arm/shield
What's included: One lower spray arm with attached shield Install notes:
- Disconnect power and turn off water supply before servicing
- Remove lower rack; lift off old arm assembly per model design
- Clear any debris from pump outlet and sump before installing
- Ensure the new arm spins freely and is fully seated; test for smooth rotation
Do-It-Yourself Stories from Customers like You
Dishwasher was noisy not cleaning well and spray arms were loose Steve S. • Rochester , MN • September 10, 2016
Replaced upper and lower spray arms, plus nylon bearings.
Read more
More
$70.76
- Compare At:
-
$84.91
- You Save:
-
$14.15
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9740674
This drain cover gasket seals the drain/pump cover at the bottom of the dishwasher tub to keep wash water contained. Replacing a cracked or flattened gasket helps stop leaks from the base and protects nearby components.
- Creates a watertight seal between the drain cover and sump opening
- Helps prevent leaks onto the floor or into the dishwasher base during cycles
- Common signs of failure: puddles beneath the unit, dampness in the base, or a visibly hardened/cracked gasket
- Good practice to replace when the drain cover is removed for service to ensure a proper reseal
What's included: 1 drain cover gasket Install notes:
- Disconnect power and shut off water supply before servicing
- Remove the lower rack (and spray arm if required) to access the drain cover per your model
- Clean mating surfaces; install the new gasket evenly without twists
- Reassemble and run a short cycle while checking for leaks
Do-It-Yourself Stories from Customers like You
Debris got into the impeller and broke it Thomas L. • Westport , MA • November 30, 2014
Replaced the drain & wash impeller kit.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676455
Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$24.95
- Compare At:
-
$29.69
- You Save:
-
$4.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3378186
Dishwasher middle wash arm manifold tube holder. This holder will have a split at the 3:00 position for easy removal from the manifold tube.
Do-It-Yourself Stories from Customers like You
Upper spray arm assembly broke Edward M. • Lehighton , PA • March 22, 2020
It took about 10 minutes. I took top basket out, took pics so I could see how it was. I marked on the basket where it was, took off the assembly and put the new one on. It's working great
Read more
More
$22.95
- Compare At:
-
$27.31
- You Save:
-
$4.36
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676453
Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$30.95
- Compare At:
-
$37.14
- You Save:
-
$6.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3373234
This dishwasher door spring bushing—also called a door spring bearing—sits at the spring's frame anchor to provide a pivot and reduce wear. Replacing a worn bushing restores door balance and helps prevent the door from dropping or slamming open.
- Provides the pivot/anchor surface for the door spring at the cabinet frame
- Maintains balanced door opening and closing force
- Reduces friction, wear, and squeaks at the spring connection
What's included: Includes 1 bushing. Install notes:
- Disconnect power at the breaker and shut off water supply.
- Remove the toe panel and mounting screws; slide the dishwasher out slightly to access the door springs.
- Support the door, release spring tension, replace the bushing at the frame anchor, and reattach the spring.
- Inspect both sides and replace worn components in pairs to keep door tension even.
Do-It-Yourself Stories from Customers like You
The dishwasher door spring broke. Rachael T. • Junction City , OR • November 07, 2022
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached...
Read more
More
$6.95
- Compare At:
-
$8.27
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: 675679
Color: White. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For grey order 676458. To attach these tine tips you will need to order the dishrack white touch-up paint WP676453.
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3369769
Dishwasher door panel insert. Reversible: white color on one side, black on the other.
Do-It-Yourself Stories from Customers like You
Rusted out front panels but dishwasher still working perfectly so kind of a waste to buy a new dishwasher Dennis Y. • Torrance , CA • October 13, 2014
Bought new top and lower front panels, removed/replaced rusted out panels & now dishwasher looks good as new! Only $34 from Appliance Parts Pros. Better than spending $500 on a new dishwasher.
Read more
More
$34.95
- Compare At:
-
$41.59
- You Save:
-
$6.64
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3378144
This is the dishwasher manifold tube only. It attaches to the bottom of the upper rack. For the complete kit order 675808. Also consider checking the mount that attaches this manifold tube to the dishrack. For the mount order WP8539324.
Do-It-Yourself Stories from Customers like You
Rotted manifold tube Joseph L. • Hermantown , MN • December 26, 2015
Part was updated from original equipment (3 pieces) to a one piece tube.
Snip the top of hanger loop then install. Just a couple minute job.
Updated tube is much better than the original design.
Read more
More
$44.95
- Compare At:
-
$53.94
- You Save:
-
$8.99