Search Results

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

I fixed it by replacing the drain pump and the inverted board. Read more

Removed two securing screws from side of dishwasher. Pulled out of cabinet careful to not over extend supply/drain/electric connections. Layed unit on side, removed two clamps from each end of drain pump as well as one electrical connection, removed bad pump, replaced connections and clamps, electrical connection. Ran a cycle while out of cabinet to ensure no leaks, replaced unit and screwed back into cabinet. Whole thing took 20 minutes. Read more

We pulled the dishwasher out, took it to the garage and set it up on sawhorses and planks so we could access the bottom. We plugged it in and filled it with water and ran a quick cycle. As soon as the circulation pump kicked on water came spraying out from the rubber boot in the diverter assembly. It appears that there was a factory defect in the hose. Unfortunately, the water got into the pump motor over a few loads and was eroding the brushes on the motor. We decided to replace it as well.... Read more

Pulling the dishwasher, it was obvious we had a slow leak under it. We had a slow leak from the diverter motor area in the sump. Sure enough, it looked like the gasket around a shaft had to be the culprit. The gasket was attached to the sump assembly, or the motor. We took a chance and ordered a new sump assembly for a mere $90 and went for it. All of the trays had to come out. The lower spray arms. Then the distribution runs to the middle rack arms and upper rack arms. Finally, the original... Read more

Tried to fix with a non GE part, didn’t work. Your GE brand pressure sensor worked like a charm Read more

• lights flashing or blinking
• Will not drain

Dishwasher died after 1 year and two weeks after purchase! The Bosch tech arrived and recommended replacing the drain pump (as well as cleaning the filter in vinegar). Ordered pump from APPros and it arrived THE NEXT DAY! Took out old one.... installed new one... and it worked! The new pump fit perfectly. Read more

Ordered the correct part/ Pump from this Awesome website and replaced the drain pump. Good to go!! Read more

• Will not drain

I ordered a new pump on this website. They provided me with written directions as well as a video to follow along with on how to change the pump. As always it wasn't as easy as the video, but that was the mechanic no the tool! Great job on the service. Will order parts from here again. Read more

• Noisy
• Leaks water

Replaced drain pump. Your video on your web site was very helpful. Read more

I took it apart and found the drain pump motor had come apart. I found appliancepartspros.com and read the reviews for this company. Customers were very satisfied with the parts and service. I ordered the parts (at a savings of over 30% from my local appliance store) and had them in 2 days (YES TWO DAYS). Totally excellent service. Put the washer back together and it works like new. The repair was very easy to do myself and saved me well over $100. I recommend your company to every do it... Read more

• Will not drain
• Leaking
• Pumps but will not spin

Looked up the part on your website, ordered it, it came in the next day, watched the install video that you provided, installed it in a few minutes, happy wife! Read more

It was a fast fix. its a Maytag Centennial Top load washer. it took me about 20mins to remove the pump and instal the new one.Most of the time was spent moving the washer. Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

My dishwasher was leaking and I called to have a certified technician come to diagnose the problem. I removed the kick panel from the bottom of the machine. He turned it on and we saw that water was leaking from the bottom. He said I needed a Sump kit but it wasn't in stock. The cost was $170 plus tax and labor cost was another $140. So I talked it over with dad and ordered the Sump kit, the hose clamp and a new diverter motor as mine was yellowed with age. The cost of all these parts and... Read more

• Will not drain

It was a relatively easy fix. Removed the small access panel at the back of the washing machine after unplugging the unit. The pump is right there. Disconnected the two hoses to the pump, catching some water with towels. Removed three retaining screws, then realized I had not disconnected the belt from under the unit. Easy fix, tilted the unit and disconnected the belt. Put in the new pump , connected the hoses, then reconnected the belts. Works like new! Read more