Paul April 01, 2016 for Model Number MDB7609AWB2 Dishwasher start and cancel (drain button) wouldn't light up or start or stop the dishwasher. All the other lights and switches operate. I tried the Normal-Heated dry-normal-heated dry buttons within 6 seconds of each other like it states in the technician manual to invoke the diagnostic function and all lights worked including Start Cancel button lights. Then the dishwasher started and went thru a normal washing cycle but no heated dry etc. button lit up or dried the dishes. I am able like I said to light up all buttons except Start Cancel buttons. Is this a Control Board issue or Control Panel issue. thanks paul
1 Answer Hello Paul. You will need to order and replace the control panel W10811155 on the unit. Read More...
Pm February 10, 2016 for Model Number MDB7749AWM1 First the soap dispenser failed to open. Then, a couple of weeks later, the start button wouldn't work, machine failed to turn on, however, the "heavy, normal, and light" buttons lit up. I bought a new control board and installed it in less than 15 minutes, while watching the excellent how-to video. It failed to operate. I remembered to plug it in. It still will not operate. I am stricken!! Please tell me what the problem is and let me know if I can return the control board.
1 Answer PM, This issue would most likely be caused by a faulty control panel. It does sound like the start button may have failed with all other lights illuminating. Here is a link to our return policy for the control board. http://www.appliancepartspros.com/customerservice/returns.aspx Read More...
Erik February 02, 2016 for Model Number MDB7749AWB1 I went to use the dishwasher and noticed that there was no power on the touchpad. Last year I had to replaced the touch pad due to a location issue with the start button. When I opened it up to check for power there was power to the control board. After removing the control unit I inspected the board only and found it burnt on the P9 pin for the pilot. I have tried to locate a diagram to check the other end of the pilot but have been unable to do so. Is there anything else to inspect prior to replacing the control board?
1 Answer Erik, With the control board having a burn mark at the P9 then you will want to replace the control board. Read More...
Larry December 16, 2015 All the lights work unit starts. Fills goes into wash cycle and stays their will not switch to rinse or pump out the water.
1 Answer Hello Larry. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. Here is a link to help you locate it. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Wayne December 10, 2015 for Model Number MDB7749AWW2 Dishwasher does not work. The "Wash" light goes on for about 30 seconds and than the machine turns off. Had an appliance service man come out and for $89 told me it was a control board and would cost me $428 to repair. He also said the part was located in the bottom of the dishwasher and to fix it the dishwasher had to be removed. I know the control panel is in the top front panel. Two questions -1. Is there another electronic control board or other type of electronics in the bottom of the dishwasher that could cause this problem? 2. If it is the control panel in the front panel, what part # do I need to order?
1 Answer Hello Wayne, This unit has no control in the base and will not need to be removed from its' installation to install the control board W11202746, because it is in the control panel and is accessed by removing the door liner. Read More...
Larry G December 10, 2015 for Model Number MDB7749AWB1 Only,high temp wash, heat Dry and sanitize lights up on control panel but nothing works. What do you think? I don't want to buy the wrong part.
1 Answer Hello Larry. Based on the information you provided, it sounds like the control panel W10811148 is bad and will need to be replaced on the unit. Read More...
Beth September 22, 2015 for Model Number MDB7749AWB1 Some buttons work, normal, heated dry and a few others. However, the cancel and start buttons will not work at all.
1 Answer Hello Beth. You will need to order and replace the control panel W10811148 on the unit. Read More...
Brian September 08, 2015 for Model Number MDB7749AWQ2 TYPENO.577-0 F13102574 I have researched this some and thought it was the electronic ribbon coated with corrosion like I have seen on youtube. Mine is not corroded like where it plugs into the control box. I did see a very little bit of brown on two lines going into the inside cover. Hello, Here is what it is doing. It will wash and drain forever and not proceed to to the next function to dry I want to get your control board W10298356 but want to make sure. Thanks, Brian
1 Answer Hello Brian, Many times the corrosion will be present on both sides of the connection. If electrical cleaner cannot be used to clean up the connections, the part causing the connection issue will have to be replaced, (control board W11202746 or ribbon cable W10811150). Read More...
Deanna September 07, 2015 for Model Number MDB7749AWW2 Hello, my dishwasher all the control lights came on. Let went off now none will come back on. Hubby says its the control panel. Just making sure of the correct part number needed for our maytag built in dishwasher model number MDB7749AWW2. Would you be able to tell me the price est. please and thx so much.
1 Answer Deanna, The part that would most likely be needed would be the control panel and is part number W10811149. Read More...
Mark August 13, 2015 for Model Number MDB6709AWQ1 After recent power surge from storm I started dishwasher – once started all the functions started to turn on at once – heater, water pump, clean cycle etc. So, I reset circuit breaker and reset using control panel (norm wash then heated dry – three times) – reset seems to cycle through all the functions. I started again using Normal and heated dry settings = once started the scrub light was blinking illuminated and dry cycle light is on.. After a few minutes of running, the delay hours light come on. Recommendations would be appreciated!
1 Answer Hello Mark. Based on the information you provided, it sounds like the control board W11202746 is bad and will need to be replaced on the unit. Read More...