Ge Jgp940sek2ss Parts

VERY simple fix- you do not even have to pull the range out.. I ordered a new cooktop from Appliance parts Pros. The customer sales rep Alphonso was great and walked me through the general process. I could find no explicit instructions for the repair but I muddled my way through. The fix is simple on Kitchenaid/Whirpool slide in ranges. 1. Open the oven door and remove the two phillips head screws directly below the control panel that hold the panel down.2. Lift the control panel upward and... Read more

My cooktop repair was a total success from start to finish. I reviewed and later followed the APP repair video, which helped me decide if I wanted to tackle the repairs and guided me right before I started. The APP phone staff member was very helpful verifying the parts I had identified online using the model number of my older GE Profile cooktop to locate and view the correct online exploded view diagram. I told him it was a pleasure working with him. The parts arrived within 3 days of... Read more

I removed all the individual burners so I could lift the stainless cover to expose the igniter wires. I cleaned all the wire connections and the 4 good igniters and replaced the one bad igniter. Reassembly was easy and everything worked properly when done. Video of repair was helpful and all parts ordered were correct and shipped promptly and I will definitely use AppliancePartsPros again. Read more

Refer to Mynor T. of Draper, UT Aug. 12, 2018 write-up. I benefited greatly from the above write-up. It took me a little less time to perform this repair (excluding cleaning the assembly) due to the write-up. This GE Profile gas burner cook top is a “drop-in” model meant to be installed into counter top cut outs. The glass top edges are the actual support area for the entire cook top assembly. The burner bases (on top of the glass top) are screwed to the metal case enclosure (located beneath... Read more

Second repair after 10 years of service - igniter had cracked and spill overs were causing the others to misfire. This was a two-step process. I took apart the cooktop to see what parts were neded. Screws were all rusted, I had to drill ome out. The burner gaskets broke during the process and needed replacement. One of the burners had deformed due to excess heat. After that initial diagnose, I reassembled the cooktop without the igniters and ordered all the parts I needed. The second stage was... Read more

When I moved in to my new house I noticed there was no regulator, and the gas line was copper tubing. I ordered a regulator and ran 40 of trac pipe to make it up to code. Hooking up the regulator was easy. Read more

Second repair after 10 years of service - igniter had cracked and spill overs were causing the others to misfire. This was a two-step process. I took apart the cooktop to see what parts were neded. Screws were all rusted, I had to drill ome out. The burner gaskets broke during the process and needed replacement. One of the burners had deformed due to excess heat. After that initial diagnose, I reassembled the cooktop without the igniters and ordered all the parts I needed. The second stage was... Read more

I examined the inner burner heads and determined that two of the most frequently used burners were warped and were not making good contact with the burner base. It's a GE Profile series stove about 10 -12 years old. I checked the GE Parts website, and they wanted almost $100 for the large burner head but didn't even have the small one at all, saying it was no longer available. By Googling the parts numbers, I found Appliance Part Pros, and they had both burner heads available. They were still a... Read more

Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more

Replaced regulator replaced gasket Read more

I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more

Refer to Mynor T. of Draper, UT Aug. 12, 2018 write-up. I benefited greatly from the above write-up. It took me a little less time to perform this repair (excluding cleaning the assembly) due to the write-up. This GE Profile gas burner cook top is a “drop-in” model meant to be installed into counter top cut outs. The glass top edges are the actual support area for the entire cook top assembly. The burner bases (on top of the glass top) are screwed to the metal case enclosure (located beneath... Read more

Ordered new gas valve and new knobs replacing broken. Read more

I examined the inner burner heads and determined that two of the most frequently used burners were warped and were not making good contact with the burner base. It's a GE Profile series stove about 10 -12 years old. I checked the GE Parts website, and they wanted almost $100 for the large burner head but didn't even have the small one at all, saying it was no longer available. By Googling the parts numbers, I found Appliance Part Pros, and they had both burner heads available. They were still a... Read more

Ordered a new burner base. Replacement was easy. Read more