Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Converting your dryer to propane? This gas orifice regulates LP gas flow to the burner for proper heating. Simple conversion component for LP dryers.
Change orifice Read more
Dryer won't heat or flame shuts off after 10 seconds? The igniter sensor monitors ignition temperature. Easy DIY repair with multimeter testing.
Used video and took apart dru, this was extremely helpful. I bypassed the belt and door switch. Tested gas valves (gas disconnected) with multimeter. Found that the igniter worked the first gas valve, but the second gas valve would not open and the igniter would stay on. Found a flow chart online that shows the flame detect turns on causing the gas to turn on and shuts off the igniter. I replaced it and tested again. Igniter turns on, shuts off, then power to the second gas valve turns... Read more
Dryer won't start or stops mid-cycle? A failed drive motor is often the cause. This part powers the drum rotation. DIY repair in 30-40 minutes.
I watched the video at your website. I unplugged the electric first. When I opened up the machine up, It was loaded with lint.I found the source was a hole in the vent tube outside the machine. I fixed that first . The lint had been sucked back into the machine. The first half hour was spent vacuuming out all the lint and then I could proceeded with the motor change. I followed the video exactly. I removed the screws at the two front corners, after lifting the top and controls and tying it... Read more
Supports the dryer drum and allows smooth rotation. Replace if you hear grinding noises, see excessive wear, or notice drum wobbling. Confirm fit with your model.
Replaced them. Read more
Supports and aligns your dryer door for smooth opening and closing. Replace if your hinge is cracked, broken, or snapped off to restore proper door function.
This part was the perfect fix for my broken door hinge on my LG front loading dryer. I watched a video on YouTube of a hinge replacement of a similar front loading Samsung dryer. I needed a little help from my son holding the door glass and plastic in place while re-attaching the door to the hinge, but it was an easy repair. Read more
Dryer won't auto dry or cycles run too long? This moisture sensor wire harness connects sensor bars to control. Restores accurate dry cycles. DIY-friendly.
I spoke with the experts at parts pro and they suspected the main power board. I ordered the main power board along with the control panel. Since I was taking everything apart I decided to replace other components as well- thermostats, thermistor , sensor wire. When I was all done the old LG was back to working like new. Oh while I was at it I cleaned and vacuumed out the complete machine. Great factory parts, videos p, service and videos, the price of all the parts was less than a repair... Read more
Internal exhaust duct assembly that channels hot air between dryer components. Replace if cracked, rusted, burned, or causing stains on clothing.
Https://www.appliancefactoryparts.com/content/pdfs/125631-1.pdf has the details to disassemble the dryer to access the vent part that cost apx$28. 1.5 hrs and some patience along with a screw driver and players was alll it took to to remove the cover, control panel, front cover, drum, belt, gas line and manifold assembly, flame tube? And rear drum panel in order to replace worn part. Reassembled in 15minutes to clean and vacuumed dryer. Works great now. Read more
Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
Felt seal creates an airtight barrier between drum and bulkhead for efficient drying. Replace if worn, torn, or causing longer dry times and lint buildup.
I took the dryer apart.....first had to clean out all the lint here and there. Took the drum out, inspected the belt and back support wheels. They seemed to be fine. In the front the drum turns on two supports that have a Teflon glide. Those two glides had been worn off with their pad so metal was rubbing against metal. Went online to appliancepartspros.com and looked up on the schematic what parts I needed. I also had called around locally and the same parts cost twice as much....so I... Read more
Fix loud banging, grinding noise, or poor drying performance with a new dryer blower wheel. Restores proper airflow through drum and exhaust vent.
I replaced the dryer motor. I followed the repair video on the Appliance Parts Pro site, with a few modifications to the procedure. I loosened the control panel and flipped it forward to improve access to the wiring connectors. I also loosened the front panel and tipped it forward before disconnecting the door switch as there wasn't enough space to disconnect the switch otherwise. Removal of the blower assembly required the use of penetrating lubricant as the assembly was stuck on the motor... Read more
Replacement screw that secures the handle to the oven door trim. Needed when original screw is stripped, rusted, lost, or damaged during handle replacement.
Overall the fix wasn't too hard. The challenge was putting the oven door back together and holding it together while trying to tighten the screws. Enlisted my wife's help to hold the door and at first the handle screws wouldn't tighten. My cordless screwdriver's battery was under-charged. Once I switched batteries I was able to tighten the screws. Seemed like I needed to push too hard (my wife freaked "not so hard you will strip them!") however pushing hard was what was needed. Both screws... Read more
Timer won't advance or dryer loses heat? This cycling thermostat regulates exhaust temperature. 15-30 minute DIY fix restores consistent drying heat.
I went ahead and ordered the element, and the 2 different thermostats not knowing exactly which one might be the problem. My My Maytag opens from the front and it was actually pretty easy to get into. Also gave me the opportunity to vacuum out the inside of the dryer. Pop the top off, remove the wires that connect the door switch (noting the colors and placement), take off the 2 inside nuts that hols the fron on, pull it forward and lift it off, 3 inside screws to take out to inside lint part... Read more
Factory fastener screw secures panels, brackets, and trim inside appliances. Replace missing, stripped, or damaged screws to restore tight fit.
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more
Dryer stops mid-cycle or won't stay closed? A worn door strike causes the latch to slip, triggering safety shutoffs. Simple 2-minute fix with a screwdriver.
Chatted with 1 of your professionals and within a minute she had the part and it was on it's way. The job was VERY easy to fix and the part is working great! Read more
Dryer not heating or blowing cold air? A failed igniter won't glow to light the gas burner. This 15-minute repair restores heat and drying performance.
When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more
Dryer stopped tumbling? A worn motor pulley causes belt slippage and no drum rotation. Direct replacement part, typically takes 15-30 minutes to install.
I put the new motor pulley on and re-attached the belt. I watched a crap ton of YouTube videos and performed what the professionals did. I ate food before the repair so my body would perform as a top ranked athlete. I moved my body in multiple positions between sitting down and kneeling over. I used a soft towel for my knees when kneeling. I asked my wife to "hold this" while I attached the belt. I screamed, "Quit moving it!!!!! (The drum)," while I put the belt around the pulley. I left my... Read more