Lse7806ace 19841940Aj Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001274
The Water Inlet Valve is an OEM part for Whirlpool appliances. It controls the flow of water into the washing machine.
Causes of a faulty water valve can include wear and tear over time, sediment or mineral buildup, electrical component failure, or physical damage. These factors can result in issues such as inadequate water flow, water leakage, or the appliance not filling with water.
Symptoms of a bad water valve may include:
- Insufficient water filling in the appliance
- Slow or no water flow
- Water leakage from the valve area
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Water dripping in tub thru fill spout while not in use H Gene P. • Muskogee , OK • June 24, 2019
Replaced the water valve. Easy repair. The repair video was spot-on. Tools needed: Slip joint pliers for removing and attaching the hoses and moving the hose clip. 5/16 nut driver. Phone to take a picture so I could get the wires put back right.
Shut off the water and unplug from power. Remove the hoses. Using a 5/16 nut driver remove the single screw that holds the bracket, lift bracket slightly and pull from the washer. There is a little slack in wires and fill hose to work with. Take a...
Read more
More
$115.21
- Compare At:
-
$135.95
- You Save:
-
$20.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003441
The OEM Replacement is a bearing designed to function as the rear bearing in Whirlpool front-load washers. It also works as the upper brake bearing in top-load washers. Positioned near the tub's brake assembly, this component plays a significant role in the operation of the washer. In top-load washers, it resides above the brake assembly.
Causes of a bad bearing can include prolonged wear and tear, exposure to excessive loads, or water intrusion that leads to rust and corrosion. A compromised bearing can lead to more significant issues if not addressed promptly.
Symptoms of a bad bearing include:
- Loud, unusual noises during the wash or spin cycles
- Excessive vibration or movement of the washer
- The drum not rotating smoothly or becoming stuck
- Leaks around the drum area
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Noisy spin cycle Gregory E. • Halifax , PA • April 17, 2017
I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will...
Read more
More
$17.95
- Compare At:
-
$21.18
- You Save:
-
$3.23
Genuine Whirlpool part
By: Whirlpool
Part Number: W10841140
This OEM Replacement Part is an Adhesive designed for use in high-temperature areas of your Whirlpool appliances. Approximately 7.5 inches long, this white adhesive is suitable for securing parts such as grate feet, gaskets, and felt seals. It is especially useful, particularly in hot zones like a cooktop. The heat-resistant properties of this adhesive ensure that the bond integrity remains uncompromised even under high-temperature conditions.
Contained in a 3oz bottle, this adhesive forms a resilient bond between various components. It is commonly used in conjunction with gaskets, felt seals, and rubber feet. The RTV high temp silicone adhesive/sealant guarantees the safety and longevity of your appliance by ensuring a secure fit of parts exposed to high heat.
Do-It-Yourself Stories from Customers like You
My 20 year old maytag washer was knocking durring the wash cycle Dennis K. • Antioch , CA • November 15, 2015
I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the...
Read more
More
$17.95
- Compare At:
-
$21.18
- You Save:
-
$3.23
Genuine Whirlpool part
By: Whirlpool
Part Number: 12002351
The Washer Drive Motor is an OEM part for Whirlpool washing machines, designed to convert electrical energy into mechanical motion to drive the washing machine drum. This motor is a pivotal component in ensuring your washer operates smoothly across various cycles, whether it's agitating clothes in the wash cycle or spinning them dry.
Causes of a bad Washer Drive Motor can range from wear and tear over time, overheating due to overloading or obstructed movement, and electrical failures such as short circuits or damaged wiring.
Symptoms of a failing Washer Drive Motor include:
- The washer not agitating or spinning correctly
- A burning smell or unusual noises during operation
- The washing machine failing to start
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The drive motor gave off a lot of smoke while on spin and then it would shut down when doing any function due to overheating Michael G. • Sarasota , FL • September 08, 2014
I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you.
Read more
More
$124.95
- Compare At:
-
$170.33
- You Save:
-
$45.38
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596669
The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.
Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Leaks at the hose connection points
- Hoses slipping off the connections
- Visible rust or damage on the clamp
- Reduced appliance efficiency due to leaks
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not stop filling with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
My washing machine smelt horrible Bryan W. • Ogdensburg , NY • August 20, 2018
First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available....
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP354987
The Idler Shaft Retaining Ring is an OEM replacement part for Whirlpool dryers. Also called an "E" ring, it is a sealing gasket positioned between the front and rear housing omponents. Maintaining an airtight seal prevents gas leakage and promotes efficient drying performance.
Causes of a bad retaining ring commonly involve compression loss of the rubber gasket material over many years of heating cycles. Exposure to petroleum-based cleaners may prematurely deteriorate the seal as well.
Symptoms of a failed 'E' ring include:
- Gas leaks emitting foul odors around seams or vents
- Reduced heat conductivity hampering dryer functioning
- Moisture accumulation shortens fabric lifespan
- Drafts compromising indoor air quality and energy bills
This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models.
Do-It-Yourself Stories from Customers like You
Loud squealing noise William B. • Rocky Mount , NC • December 17, 2018
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!!
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP213045
The Tub to Pump Hose is an OEM part for Whirlpool washing machines. This hose connects the tub to the pump, allowing water to drain from the tub during the washing and rinsing cycles. It is designed to handle the water flow and pressure within the washer, ensuring efficient drainage.
Causes of a bad tub to pump hose can include wear and tear over time, exposure to harsh chemicals or debris, or damage due to accidental punctures or kinks. When the hose is compromised, it can lead to drainage issues and potential water leaks.
Symptoms of a bad tub to pump hose include:
- Water not draining from the washer
- Leaks or puddles underneath the washer
- Visible cracks or wear on the hose
- Error codes related to drainage problems
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Leaking water from bottom of washer found hose cracked just below the tub Terry S. • Morgan Hill , CA • April 23, 2014
I replaced the hose between the tub and the pump. The clamp screws were quite rusted but I used a socket wrench on them since they have hex heads in addition to the screwdriver slot. If I had tried to use a screwdriver, I think it would have been difficult. I did not reuse the original clamps but replaced them with hardware store hose clamps.
Read more
More
$46.95
- Compare At:
-
$55.87
- You Save:
-
$8.92
Genuine Whirlpool part
By: Whirlpool
Part Number: WP312967
The Clamp is an OEM part for Whirlpool dryers. This clamp ensures tight and secure connections within the dryer, particularly in securing ducts and vents that are essential for proper airflow and operation.
Clamps may need replacement due to loss of tension, corrosion, or damage from regular use. A compromised clamp can lead to operational issues such as prolonged drying times or excessive noise, resulting from loose parts or improper ventilation.
Symptoms of a bad Clamp include:
- Loose or detached vents or hoses, leading to inefficient dryer operation.
- Increased drying times, as a result of compromised airflow from unsecured ducts.
- Unusual vibrations or noise, indicating that internal components may not be securely fastened.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
This part fixes the following symptoms
-
No heat or not enough heat
-
Takes too long to dry
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Lack of heat and long drying times Allan H. • Baroda , MI • March 06, 2016
Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was...
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP6-3033630
The Idler Pulley Arm is an OEM component specifically designed for Whirlpool brand clothes dryers. It pivots to lift belt tension and remove slack during dryer tumbling.
Symptoms of a problematic idler pulley arm include:
- Drive belt slips off pulleys or tracks improperly
- Reduced drying due to inefficient tumbling
Potential causes involve typical wear from extended usage. Seizing bushings or restrictive movement may diminish functionality over time as well.
This genuine OEM Whirlpool part is compatible with models including some brands produced by KitchenAid, Maytag, and Kenmore.
Do-It-Yourself Stories from Customers like You
Clothes dryer had developed a loud squealing noise the problem turned out to be the idler pulley wheel Don F. • Bakersfield , CA • September 19, 2020
I removed the front panel of the dryer by removing 2 screws and lifting it up and out. Then I removed 4 screws from the bracket holding the tub in place. I had previously removed the 4 screws from the rear inspection cover so I reached in and released the spring loaded belt that turns the tub and then removed the idler pulley wheel. The tub just lifts out at that point, exposing the 2 Drum support rollers in the rear.
I removed the 2 rear drum support rollers and decided to order 2 of...
Read more
More
$54.36
- Compare At:
-
$64.69
- You Save:
-
$10.33
Genuine Whirlpool part
By: Whirlpool
Part Number: 205000
The Motor Mount Roller and Spring Kit is an OEM part for Whirlpool washing machines. This kit includes the motor mount, roller, and spring, which work together to support and stabilize the motor during the wash and spin cycles. These components are crucial for minimizing vibrations and ensuring the motor runs smoothly and efficiently.
Causes of a bad motor mount, roller, or spring can include normal wear and tear over time, heavy or unbalanced loads that put extra stress on the components, and accidental damage or impact.
Symptoms of a bad motor mount, roller, or spring include:
- Excessive noise during the wash or spin cycle
- Vibrations or shaking of the washing machine
- The drum not spinning properly
- Motor misalignment or poor performance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not agitate
-
Burning smell
See more...
Do-It-Yourself Stories from Customers like You
Maytag clothes washer would not spin or drain Ben M. • Wallingford , CT • September 29, 2018
The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell.
At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer...
Read more
More
$48.95
- Compare At:
-
$58.25
- You Save:
-
$9.30
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22002360
The Water Inlet Valve is an OEM part for Whirlpool washing machines. It controls the flow of water into the washer during the filling cycles, ensuring the proper amount of water is used for washing and rinsing clothes. This valve plays a critical role in the overall performance and efficiency of the washing machine.
Causes of a bad water inlet valve can include mineral deposits or debris clogging the valve, electrical failure, or wear and tear from regular use.
Symptoms of a bad water inlet valve include:
- Washer not filling with water
- Slow filling or no water flow
- Leaking water from the valve area
- Washer not advancing through cycles properly
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Water wouldn't shut off tub kept filling William M. • Stroudsburg , PA • April 24, 2016
Ordered a new inlet water valve . Super fast delivery ordered on a Wednesday afternoon was here Thursday morning , standard shipping , I was impressed !!
Removed the old valve , installed the new , checked for leaks no issues , washer is back on line and my Honey is very happy with me .
Read more
More
$109.70
- Compare At:
-
$131.64
- You Save:
-
$21.94
Genuine Whirlpool part
By: Whirlpool
Part Number: 206638
The Siphon Break is an OEM part for Whirlpool washing machines. It is a critical safety component that prevents the backflow of contaminated water from the washer into the fresh water supply line. For the gasket use part number [AP6005834], For the siphon elbow use part number [AP4024083]
Causes of a faulty siphon break include physical damage, clogging due to mineral buildup or debris, or general wear and tear over time.
Symptoms of a bad siphon break:
- Water leaks or puddles around the washing machine
- The washer not filling with water properly
- Potential for contaminated water to enter the fresh water supply
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.
Do-It-Yourself Stories from Customers like You
Syphonbreak was leaking James O. • Bryant , AL • September 04, 2015
We ordered parts from appliance parts pros and I fixed it.
Read more
More
$54.95
- Compare At:
-
$64.84
- You Save:
-
$9.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP307473
The Thermal Fuse is an OEM part for Whirlpool dryers. This safety device protects the dryer from overheating by cutting off power if the dryer exceeds a certain temperature. It is crucial for maintaining safe operation and preventing potential fire hazards. This thermal fuse has 1/4-inch terminals and operates around 243 degrees F.
Causes of a bad thermal fuse include lint buildup causing overheating, blocked ventilation, or a malfunctioning thermostat. These issues can lead to the fuse blowing to prevent further damage or risk.
Symptoms of a bad thermal fuse include:
- Dryer not starting
- No heat in the dryer
- Dryer shutting off mid-cycle
- The dryer running but not heating
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Catastrophic failure of the dryer cycling thermostat in a maytag neptune super stack Richard M. • Cornish , NH • October 19, 2020
Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short...
Read more
More
$47.95
- Compare At:
-
$56.58
- You Save:
-
$8.63
Genuine Whirlpool part
By: Whirlpool
Part Number: WP207166
The Lid Check Switch is an OEM part for Whirlpool washing machines. It ensures the washer operates only when the lid is securely closed, providing a safety mechanism to prevent the machine from running with the lid open. This is the switch only. For the complete assembly including the switch order part number AP6006235.
Causes of a bad lid check switch can include wear and tear over time, damage from repeated use, or issues with the electrical connections. If the switch fails, it can prevent the washer from starting or interrupt the wash cycle.
Symptoms of a bad lid check switch include:
- Washer not starting
- Interruption of the wash cycle
- Error codes indicating lid issues
- Lid not locking properly
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not fill with water
-
Will not agitate
See more...
Do-It-Yourself Stories from Customers like You
My washer stopped it just sttoped working Charles T. • Houston , TX • February 01, 2015
First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you...
Read more
More
$44.95
- Compare At:
-
$53.49
- You Save:
-
$8.54
Genuine Whirlpool part
By: Whirlpool
Part Number: LA-1003
The Door Catch Kit is an OEM part for Whirlpool dryers. It includes the door catch and the necessary mounting hardware to secure it in place. This kit ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently.
Causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly.
Symptoms of a bad door catch include:
- The dryer door not staying closed
- Difficulty latching the door shut
- The dryer stopping mid-cycle due to the door opening
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Door won't close
-
Shuts off too soon
-
Doesn't shut off
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Door clip to my dryer broke Richard D. • North Dinwiddie , VA • March 15, 2014
Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done.
Total time was less than 10 minutes. Works like new.
Read more
More
$24.95
- Compare At:
-
$29.94
- You Save:
-
$4.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP285655
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Water leaks around the hose connection points
- The hose slipping off the fitting
- Visible rust or wear on the clamp
- Difficulty in tightening the clamp to secure the hose
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Syphonbreak was leaking James O. • Bryant , AL • September 04, 2015
We ordered parts from appliance parts pros and I fixed it.
Read more
More
$9.95
- Compare At:
-
$11.74
- You Save:
-
$1.79