Sde 4606Ayw Parts

This multi-temperature cycling thermostat regulates the dryer's drum heat, switching the heater on and off to match the temperature setting you choose. It can help restore consistent drying if temperatures are erratic, loads run too hot, or cycles take too long.

• Maintains target temperature by opening and closing the heater circuit across multiple heat settings
• Provides calibrated temperature control for safe, efficient drying
• Failure may present as no heat or low heat, overheating, very long dry times, or inconsistent temperatures
• Intended for models with multiple temperature selections

• Unplug the dryer; shut off gas supply if applicable. Allow the appliance to cool before servicing.
• Take a photo of wire positions; move wires to the new thermostat one at a time to matching terminals and ensure snug connections.
• Remove/install mounting screws and seat the thermostat flat against the mating surface for proper sensing.
• After reassembly, clear lint passages and verify proper vent airflow.

• If there's no heat at all, also check the thermal fuse, high-limit thermostat, heating element (electric), or igniter/burner components (gas).
• Restricted venting can mimic thermostat issues and cause overheating or long dry times.

This internal-bias thermostat regulates dryer drum temperature by cycling the heat on and off, helping maintain consistent drying performance and protect against overheating.

• Controls the cycling temperature of the heating circuit to prevent underheating or overheating
• Helps resolve symptoms like no heat, not enough heat, long dry times, or temperature swings
• A faulty thermostat may cause overheating that can trip the thermal fuse
• Located on the blower housing on many models

• Disconnect power and shut off gas (for gas dryers) before servicing
• Access the blower housing; note wire positions and transfer one at a time
• Mount the thermostat flush to the housing for proper sensing
• After installation, run a test cycle to verify proper heating

The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe and efficient conversion.

Over time or due to specific needs, you might need to convert your appliance from natural gas to LP gas. Causes for needing this conversion include moving to an area where only LP gas is available or preferring LP gas due to its efficiency and environmental benefits.

Symptoms indicating the need for a gas conversion kit include:

• Moving to a location that only supplies LP gas
• Changing energy preferences for better efficiency
• Appliances set up for natural gas needing adaptation to LP gas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This thermostat is a temperature-sensitive switch used in the appliance's heating circuit. It opens and closes at a specific temperature to regulate or limit heat, helping maintain correct operation and protect components from damage due to overheating.

• Monitors temperature and switches the heating circuit on/off at its preset trip point
• Helps prevent overheating and heat-related component damage
• Failure symptoms can include no heat or underheating, overheating or burnt odors, or heat that won't shut off
• May cause intermittent heating or frequent cycling as the unit warms and cools

• Disconnect power and allow the appliance to cool completely; shut off gas supply if applicable
• Access the thermostat, note/photograph wire positions, and transfer wires one at a time to the new part
• Mount securely against the proper surface/bracket so the sensor has good contact
• Restore power and test operation; if issues persist, diagnose related heating components per the service manual

10 - 16 x 1/2

This timer regulates the length and progression of the drying cycle. When it fails, the dryer may not start, advance through the cycle, or shut off as expected. Replacing the timer restores reliable cycle control and end-of-cycle shutoff.

• Advances the selected cycle by opening and closing internal contacts as the dial turns
• Routes power to key circuits (motor and heat) at the proper time during the cycle
• Common symptoms include: cycle won't advance or end, dryer runs too long/short, won't start, or dial doesn't move
• Helps ensure consistent, predictable drying performance and automatic shutoff

• Disconnect power before servicing; for gas dryers, also shut off the gas supply
• Access the control console, remove the knob and mounting screws to release the timer
• Transfer wires from the old timer to the new one one-at-a-time, matching terminal positions
• Secure the timer, reinstall the knob and console, and run a test cycle to ensure proper advance and shutoff

This cycling thermostat regulates your dryer's internal air temperature by switching the heat source on and off, helping prevent overheating and keeping drying performance consistent. Replace it if temperatures are erratic, items run too hot, or dry times increase. What it does:

• Monitors drum air temperature and opens/closes to control the heater
• Maintains stable temperatures across fabric/temperature settings
• Failure symptoms include no or low heat, overheating/scorch smells, long dry times, or inconsistent cycling
• Helps protect against damage from excessive heat when functioning correctly

• 1 cycling thermostat

• Disconnect power; if it's a gas dryer, also shut off the gas supply
• Allow the unit to cool; access the thermostat (typically on an internal air duct or blower housing); note wire positions
• Transfer wires to the new thermostat one at a time; mount flush against the metal surface; do not overtighten
• After installation, clean lint passages and ensure proper airflow and temperature control

This spring fastener applies constant tension to hold a component securely in place inside your appliance, helping prevent looseness, vibration, or gaps. Replacing a fatigued or missing clip restores a tight, reliable fit.

• Provides spring tension to clamp and retain a part, seal, or panel
• Helps maintain alignment and reduce vibration or rattling
• Restores secure attachment when the original clip is bent, stretched, or missing
• Symptoms can include a part not staying put, visible looseness, or a clip that's damaged or gone

• Disconnect power; turn off water supply if applicable
• Use needle-nose pliers or a suitable spring tool; wear gloves and eye protection
• Note the original orientation before removal to ensure proper reinstallation
• Make sure the mating part or seal is fully seated and the fastener is fully engaged before reassembly

Considered a crucial part of the dryer, the blower fan assembly is the part that pulls in air from outside and then circulates that air in the drum to ensure clothing gets dry. After the air is moved around the drum, it is then moved through the exhaust vent. This part is located on the motor shaft and is made of durable plastic. Regular use can lead to wear and tear or damage to this component. If this occurs, the air in the dryer may not dry the clothing. In this case, the blower fan assembly will need to be replaced.If the blower fan assembly needs to be replaced, first the dryer should be unplugged from power. Take the cabinet top off and remove the front panel on the appliance. Take out the drum, remove the motor clamp, and loosen the blower fan so it can be removed. Take it out and replace it with the new blower fan assembly.The blower fan assembly is designed to be used with dryers manufactured by Amana and Speed Queen. It is sold as an individual part. This is an authentic OEM replacement part that is sourced directly from the manufacturer.

This drive motor and pulley assembly powers the belt-driven system to rotate the drum or tub. Replacing a weak or seized motor restores consistent rotation and reliable cycle performance on compatible 120V/60Hz models. What it does:

• Drives the belt that turns the drum or tub for wash/spin or tumble
• Provides correct 120V/60Hz operation for North American units designed for this spec
• Helps address symptoms like humming with no start, drum/tub not turning, belt not moving, or burning/motor smell
• Replaces a worn pulley to improve belt tracking and reduce slippage or squeal

• 1 motor and pulley assembly

• Disconnect power before servicing; for gas units, also shut off gas supply
• Relieve belt tension, note routing, and transfer wiring/connectors from the old motor
• Align the pulley and set proper belt tension; rotate by hand to verify free movement before restoring power

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.

For complete assembly for easier installation order WP37001287

The dryer timer controls the sequence and duration of each cycle. When its contacts or motor fail, the dryer may not start, advance, or shut off. Replacing the timer restores accurate cycle control and automatic advance.

• Sequences power through timed contacts to run motor, heat, and related circuits
• Advances the dial and stops the dryer at the OFF position
• Provides cycle timing for selected settings
• Common symptoms of a failing timer: cycle won't advance, won't start on certain settings, runs too long or won't shut off, only one cycle works

• Unplug the dryer before servicing
• Access the control console; label or photograph wire positions
• Move wires to the new timer one at a time, mount the timer, and reinstall the knob/panel
• Test cycle advance and shutoff after reassembly

This 240-volt heater assembly restores the appliance's ability to generate and maintain heat during operation, helping cycles reach designed temperatures for proper performance and results. What it does:

• Converts electrical energy into heat for the appliance's heating circuit
• Helps the unit reach and hold target temperatures during heat-required portions of the cycle
• Replaces a damaged, shorted, or open heating element
• Symptoms can include no heat when expected, longer-than-normal cycles, tripped breakers, or heater-related error codes

• 1 heater assembly

• Disconnect power at the breaker before servicing; 240V circuits can be hazardous
• Document wire locations and move connectors one at a time to the new assembly
• Avoid bending or striking the element; ensure secure mounting and proper clearances
• After installation, check related safety devices (high-limit, thermostats, fuses) and verify the circuit has correct voltage and continuity

This electric heater restores the heat your machine needs to reach and maintain proper operating temperature. Replacing an open or weak element brings back consistent heating so cycles complete as intended. What it does:

• Converts electrical power into heat within the appliance's heating circuit
• Works with thermostats and controls to maintain target temperature
• Common symptoms: no heat or lower-than-expected temperatures
• Extended cycle times or inability to reach set temperatures

• 1 heater element

• Disconnect power at the breaker and allow the unit to cool completely before service
• Note wire positions; move connectors one at a time and avoid stressing the coil/insulators
• Inspect related thermostats, cutoffs, wiring, and airflow/circulation issues to prevent repeat failures
• The part matches your model's required voltage rating (208V) before restoring power