Solenoid Parts

The Water Valve is an OEM part for Whirlpool ice machines. This part controls the flow of water into the ice maker, ensuring it receives the correct amount of water for ice production.  

Causes of a bad water valve can include wear and tear from regular use, mineral buildup from hard water, or electrical failures. 

Symptoms of a bad water valve include:

• The ice machine not producing ice
• Slow or inconsistent ice production
• Leaking water from the valve area
• No water entering the ice machine
• You should replace the water valve if it becomes faulty or damaged.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This water inlet valve regulates the flow of household water into the appliance. When the control energizes the solenoid, it opens to deliver the correct amount of water for filling and operation, restoring proper flow and performance.

• Controls on/off flow from the household water supply
• Opens when signaled to provide the correct amount of water for fill functions
• Helps maintain consistent water flow to the system
• Common failure symptoms: no water flow, slow fill, intermittent filling, or leaking at the valve body

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Note tubing and wire locations before removal; transfer any brackets or clips as needed
• After installation, restore water and power, check for leaks, and purge air from the lines

This gas valve includes the coils. For the coils alone use part number 279834

This water inlet valve assembly controls the flow of water from the home supply into the refrigerator. Replacing a faulty valve restores proper water delivery to the ice maker and/or dispenser for consistent ice production and dispensing.

• Opens and closes to send water to the ice maker and/or dispenser as commanded by the refrigerator
• Common symptoms: no water from dispenser, no ice production, slow/weak dispenser flow
• May also present as continuous dripping into the ice maker/dispenser or leaks around the valve body
• If water lines and filter are clear but filling is inconsistent or absent, the valve may be at fault

• Disconnect power and shut off the water supply before servicing
• Place a towel or shallow pan to catch residual water; note line and wire locations for reassembly
• Ensure tubing is fully seated in fittings; avoid overtightening plastic connections
• Restore water and power, then check all joints for leaks and run the dispenser to purge air/debris

The Gas Valve Assembly is an OEM replacement part for LG gas dryers. It precisely controls the flow of gas to the burner unit during drying cycles. 

Symptoms of a faulty gas valve include: 

• Inadequate or inconsistent heating 
• Burner failure to ignite properly
• Error codes related to gas or pilot light issues

Causes may involve wear and tear of valve seals over extended use, blockages limiting gas flow, or damage like dents that compromise valve integrity.

This authentic LG assembly is compatible with select Kenmore brand models. 

This dual water inlet valve controls water flow to a refrigerator's ice maker and dispenser. Replacing a sticking or leaking valve restores proper filling and reliable dispensing while helping prevent drips, slow flow, or no ice.

• Directs household water to the ice maker and door dispenser through two independent outlets
• Opens and closes electronically via two solenoids when the control calls for water
• Common failure symptoms: no water from the dispenser, ice maker not filling, slow/weak flow, or leaks/drips at the valve
• Mineral buildup, cracks, or failed solenoids can prevent sealing or operation and warrant replacement

• Unplug the refrigerator and turn off the water supply before servicing
• Relieve line pressure and keep a towel or container ready for residual water
• Label and transfer tubing and wire connectors to the new valve one at a time to maintain orientation
• Restore water, check carefully for leaks, and purge air by running the dispenser

This float controls your dishwasher's water level. As the tub fills, it rises to signal the float switch to shut off incoming water, helping prevent overfilling and leaks.

• Lifts with the water to actuate the float switch and stop filling
• Helps protect against overfilling and door leaks
• Replace if the float is cracked, deformed, waterlogged, or sticks in its well
• Symptoms can include: won't fill or stops filling early; overfilling or leaks at the door

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the float in the tub floor
• Lift the old float straight up; clear any debris; seat the new float and free up-and-down movement
• Restore power and run a fill test to proper operation and check for leaks

This water inlet mixing valve controls and blends the hot and cold water entering your washer for proper fill temperature and water level. A worn valve can cause fill problems or unwanted leaks into the tub.

• Regulates hot and cold water flow to achieve the selected temperature
• Opens and closes electrically during fill cycles
• Common symptoms: slow fill, no fill, fills with only hot or only cold, or water seeping into the tub when the washer is off
• Electrical coil-operated design for reliable operation

• Unplug the washer and shut off both water supplies before servicing
• Place a towel or pan to catch residual water when disconnecting hoses
• Note hose positions (hot/cold) and wire connectors for correct reassembly
• After installation, check for leaks and run a test fill cycle

The Water Inlet Valve is an OEM component for Whirlpool dishwashers. As the critical connector between the home supply lines and the dishwasher itself, this valve oversees the entry of water into the machine for wash and rinse cycles.

Causes of inlet valve malfunction include mineral deposits accumulating inside the valve body or worn seals no longer maintaining a tight closure following years of usage. This places increased strain on internal mechanisms. 

Symptoms consist of:

• Slow or irregular water fills failing to reach proper levels
• Fluctuating water pressure inputs 
• Drips or continuous leaks at the water connection
• Inability of cycles to advance beyond initial fill stages

This Whirlpool OEM replacement is compatible with KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers as well.

This triple water inlet valve regulates the hot/cold water supply and dispenser fills in your washing machine. Replacing a failing valve restores proper fill control and temperature selection, helping address slow fills, no fill, or water seepage into the tub.

• Regulates incoming water flow as directed by the washer's control system
• Mixes hot and cold supply to achieve the selected temperature
• Routes water to the tub and dispenser during appropriate cycles
• Common symptoms include no/slow filling, only hot or only cold working, or water dripping into the tub when the washer is off

• Disconnect power and turn off both water supplies before servicing
• Place towels to catch residual water; label and disconnect hoses and wire connectors
• Inspect inlet screens and flush supply lines before reconnecting
• Restore water and power, then run a fill test and check all connections for leaks

This door strike is the catch the latch engages to hold the oven door closed. It restores a firm, aligned close so heat stays in and the appliance can detect a fully shut door for normal operation.

• Aligns with the latch to keep the door closed and sealed properly
• Provides the catch point required for latch/lock engagement
• Wear, bending, or breakage can cause a loose door, heat escaping, or an oven light that won't turn off
• Prevents self-clean or other cycles that require a fully closed/locked door from starting

• Disconnect power at the breaker; if gas, shut off the gas supply. Allow the appliance to cool completely
• Typically mounts to the door or cabinet frame with screws; transfer and reuse existing hardware
• Position and tighten evenly so the latch engages smoothly; minor alignment adjustments may be needed
• After installation, verify the door closes fully, seals well, and the light turns off

This water inlet valve assembly regulates when and how much water enters the appliance. Replacing a failing valve restores proper filling or water delivery and helps resolve no-water, slow-fill, or drip-through-the-valve issues.

• Opens and closes to control incoming water flow as commanded by the control system
• Directs water to the appliance's water circuit for proper operation
• Common symptoms: no water entering, weak/slow flow, water seeping in when off
• Physical clues: cracked housing, mineral buildup, or a valve that hums but doesn't pass water

• Disconnect power and shut off the water supply before servicing
• Keep towels handy; relieve line pressure before disconnecting tubing/fittings
• Transfer connectors and any mounting hardware one-for-one; ensure tubing is fully seated and use appropriate thread sealant if your model uses threaded fittings
• Restore water, check all joints for leaks, then restore power and run a test cycle

This vacuum break is the washer's water-inlet anti-siphon fitting. It maintains a required air gap so the tub fills properly without drawing used water back into the supply, helping prevent leaks and backflow issues.

• Maintains an air gap at the inlet to prevent backflow/siphoning into household water lines
• Helps ensure consistent, unobstructed water flow into the tub
• Replaces a cracked, clogged, or leaking vacuum break at the fill area
• Common symptoms include leaks from the rear/top during fill, visible cracks, or restricted/noisy fill

• Unplug the appliance and shut off both water supplies before servicing
• Access the fill/inlet area; note hose routing and part orientation
• Remove hose clamps/hoses and the old vacuum break; install the new part and secure clamps
• Restore water and power, then run a fill test and check carefully for leaks

This refrigerator water inlet valve controls the incoming household water supply to the dispenser and icemaker. When energized, it opens to allow water flow, helping restore reliable dispensing and proper ice production.

• Regulates water flow to both the dispenser and the icemaker
• Common failure signs: no or slow water dispensing, no ice production, small/hollow ice cubes, valve humming but no water, or water leaking from the valve body
• Electrical solenoid-operated design opens only when signaled by the control system
• Helps maintain consistent water delivery and ice fill levels

• Disconnect power and turn off the household water supply before servicing
• Place a towel or pan to catch residual water; relieve line pressure carefully
• Transfer tubing and wire connectors one at a time to the new valve to avoid mix-ups
• Check for leaks after installation; do not overtighten compression fittings

This assembly includes the refrigerator's water inlet valve mounted on its bracket. It regulates water flow from the household supply into the refrigerator's water system to restore reliable filling for the ice maker and/or dispenser.

• Controls water flow by opening/closing the valve when the refrigerator calls for water
• Helps deliver proper water during fill cycles and shuts off cleanly after
• Common symptoms: no ice production, no water from dispenser, slow/weak flow, leaks at the valve, or loud buzzing/chattering during fill
• Mounts in the original location using the included bracket for secure fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure (dispense water if equipped) and keep a towel handy for residual water
• Move tubes and wire connectors to the new valve one at a time to maintain placement
• Restore water and power, then check all connections for leaks and proper operation

This gas surface burner head distributes fuel through its ports to create an even, reliable flame on your cooktop. Replace a clogged, damaged, or warped head to restore consistent ignition and proper heat on the affected burner.

• Channels gas through precision ports to produce a steady, even flame
• Interfaces with the surface igniter/electrode for quick, reliable ignition
• Replaces worn or clogged heads that cause weak, uneven, or yellow flames
• Helps resolve delayed ignition or a burner that won't light

• Disconnect electrical power and shut off gas supply before servicing
• Remove grate and burner cap, lift off the old head, and clean the mating surface
• Align the new head with the igniter and locating features; seat it fully before replacing the cap
• Restore gas and power; test ignition and verify proper flame pattern