Solenoid Parts

Replaced both hot and cold water inlet valves. Works like a charm, issue resolved. Read more

The tech sheet test 56 said the motor wouldn't return to zero. I ordered the "Ice Maker Assy-Lp, and the Valve Assy-Water Dual". On my particular model the ice maker is in the ceiling of the refrigerator box. After removing the water filter and two screws around the drop down water filter door, the right side panel drops down by pulling it apart from 3 plastic pop-ins. Two of them broke when the repair guy man handled it. Pulling easy and supporting the inside pieces is key. Then I unplugged... Read more

My husband fixed it, he took out the leaky valve and replaced it with the new valve, which we received in the mail from your company, which was only a short time after we ordered it. Thank you for being so prompt. Our washer is only a little over 2 years old and upon looking online, we found out this model has since been discontinued due to problems. The parts are no longer available from GE, so we were thrilled to find your company online which carried the part. It saved us a lot of money... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

I reseached these error codes and compared them to others problems. After deciding that I was gonna order the part and fix it myself I was at ease to find out it took 10min to fix! And it actually worked! The washer was pausing during cycles, cloths were soaking wet, spin cycle only worked on drain and spin at the end of the Ioad (it would spin slowly otherwise), soap dispenser still had the soap in it or it would be filled with water after the cycle was over. I watched videos on how to change... Read more

Check fan operation and was OK. Everything else worked except when microwave was started for a cycle. I looked around on internet and found someone had trouble with the door switches. I started to check door switches and found one shorted. I replaced both lower door switches and it took care of problem. Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Replaced the water valve. Easy repair. The repair video was spot-on. Tools needed: Slip joint pliers for removing and attaching the hoses and moving the hose clip. 5/16 nut driver. Phone to take a picture so I could get the wires put back right. Shut off the water and unplug from power. Remove the hoses. Using a 5/16 nut driver remove the single screw that holds the bracket, lift bracket slightly and pull from the washer. There is a little slack in wires and fill hose to work with. Take a... Read more

Replaced water inlet valve assembly Read more

Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more

Removed valve and replaced with new one. Read more

• Leaking

First I replaced the filter thinking it was the problem, but that was not the case. Next was replace water supply valve at the back of the refrigerator. It was very easy. The only thing that was in question was how to get the refrigerator side line off of the existing valve. There is a plastic slide clip that you remove and pull the line out and press the line back into the port it came out of. It was a very simple project and took about 20 minutes. Read more

• Will not fill with water
• overflowing
• Not cleaning dishes properly
• Noisy

Replaced the water supply valve and the drain dump valve. The drain hose had to be replaced also. Read more

• Not dispensing water
• Leaking

Being an ex maintainence. person, I went down and turned off the water supply. Then I started to try to find the leak by removing the rear covers for the compressor and valves. Once removing a couple of covers where the dual valve was, I spotted where the water was coming from.I then pulled the electrical plug from the wall. Between the solenoid and valve. I removed the screws that held the valve in place. Then disconnected the three hoses going into valve and removed the two electrical... Read more

• Will not fill with water

Ordered new inlet water valve and float switch kit. After repairs it now works fine. However the water inlet valve outlet end for fill hose (not water source) and wire connections (supposedly for this unit) were oriented 180 degrees opposite. I had to gently remove the blue plastic valve off the metal support bracket and turn it around and press back in place. Fortunately it appears it was designed for either orientation. Also the solenoid had to be unclipped and also rotated. Again it was... Read more

Remove the top panel by removing 3 hex nuts on the back of the washer. Inlet valve was located right underneath the panel towards the back. Remove one screw using a t20 bit and unplug the 2 plugs located on the valve. With a pair of pliers removed a tension clamp and the valve comes right off. Read more

Ordered conversion kit from Appliance Parts Pros.com and installed it myself. Most difficult part of the repair, was the removal of the front casing of the dryer to access the location of venturi tube to be changed out. The instructions were helpful, but not specific enough for my dryer. Once the casing was off, the job was not too difficult - you will need a set of short screwdrivers to remove the burner flange and close the pressure adjustment screw, normal length screw drivers will come into... Read more

Watched your repair video. Ordered the part. Fixed it! Read more