Magic Chef Door Lid Closing Propeller Parts

The Oven Inner Door Glass is an OEM part for Whirlpool ovens. The glass component is specially tempered to withstand high heat inside the oven cavity.

Size: 20 5/8 inches x 13 1/8 inches. For the glass measuring 22 3/8 inches x 14 inches order 74004857

Causes of a bad oven inner door glass can include small cracks or chips developing from regular door openings/closings, or microscopic defects that enlarge under repeated thermal cycling. Damage from accidental impacts is also possible.

Symptoms of a bad Oven Inner Door Glass include:

• Reduced visibility into the oven due to fogging, steam, or condensation buildup
• Cracks or fractures compromising the structural integrity of the glass
• Leaks or seal failure allowing heat to escape from around the door frame

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Latch Kit is an OEM replacement part for Whirlpool dishwashers. This kit includes all the necessary components to replace or repair the latch mechanism that secures the detergent and rinse aid dispenser during the wash cycles.

Causes of a faulty dispenser latch can include wear and tear over time, physical damage from impact or mishandling, or issues with the dispenser alignment or hinges.

Symptoms of a bad dispenser latch kit include:

• The dispenser door not closing or latching properly
• Leaks or drips from the dispenser area
• Detergent or rinse aid not being dispensed correctly during cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models. 

This replacement panel restores your appliance's original look while shielding internal components. Install a new panel to replace a dented, cracked, or missing piece and keep the assembly secure, aligned, and protected.

• Covers and protects internal parts while restoring the exterior finish and fit
• Provides the designed mounting surface for trim/handles; helps maintain alignment
• Replace when the panel is dented, cracked, warped, rusted, or mounting tabs are broken
• Helps resolve loose or rattling panels and visible gaps or misalignment

• Disconnect power; turn off water or gas supply if applicable
• Wear gloves and protect finished surfaces; handle carefully to avoid bending or scratching
• Transfer and reuse original screws, clips, insulation, and trim as directed by your service manual
• Fit and alignment before fully tightening fasteners

The Dairy Door is an OEM part for Whirlpool refrigerators. It serves as a cover for the dairy compartment, helping to keep dairy products like butter and cheese fresh by providing a separate, enclosed space within the refrigerator.

Causes of a bad dairy door can include wear and tear from regular use, accidental impacts causing cracks or breaks, or the hinge mechanism wearing out over time.  

Symptoms of a bad dairy door include:

• The door not closing properly or staying closed
• Cracks or visible damage on the door
• The hinge mechanism feeling loose or broken
• Dairy products not staying as fresh due to lack of proper enclosure

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Water Filter Cover is an OEM part for Whirlpool refrigerators. This cover encases and protects the water filter, ensuring it remains secure and clean while also blending seamlessly with the refrigerator's interior design.

You should replace the water filter cover if it becomes damaged or fails to secure the filter properly. Common causes of a bad water filter cover include physical damage from accidental impact, wear and tear from regular use, or warping due to temperature fluctuations.

Symptoms of a bad water filter cover include:

• Cracks or visible damage to the cover
• Difficulty securing the water filter
• The cover not fitting properly or coming loose
• Leaks around the water filter area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Lid Pin is an OEM part for Whirlpool dishwashers. This pin plays a crucial role in securing the detergent dispenser lid, ensuring that it opens and closes correctly during the washing cycle. This dishwasher detergent lid pin is also included in the cover kit 4387043.

Over time, the detergent lid pin can wear out or break due to regular use, exposure to harsh detergents, or accidental force. When the pin is damaged, it can cause the detergent lid to malfunction, leading to improper dispensing of detergent and reduced cleaning performance.

Symptoms of a bad detergent lid pin include:

• The detergent dispenser lid not staying closed
• Detergent not being dispensed correctly during the wash cycle
• Visible damage or wear on the pin
• The dispenser lid not opening or closing smoothly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dispenser Lid is an OEM replacement part for Whirlpool dishwashers. Located at the top of the dishwasher door, it provides access to add detergent and rinse aid to the internal dispenser compartment below.  This dishwasher soap dispenser lid is included in the dispenser cover kit 4387043.

Causes of a bad dispenser lid can include wear and tear of hinge points from years of repeated openings. Cracks may also arise in the plastic material.

Symptoms of a bad Dispenser Lid include:

• Difficulty fully opening or closing the lid securely
• Leaks or spills occurring from around the sealing edges
• Potential cracks that compromise lid integrity or function
• Hinges that are loose or fail to support the lid in position

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Amana, and some Kenmore models.

The Dispenser is an OEM part for Whirlpool dishwashers. It is responsible for dispensing detergent and rinse aid at appropriate times during the dishwashing cycle, ensuring optimal cleaning and drying performance.

Causes of a bad dispenser can include clogging or blockage in the dispenser mechanism, damage to the dispenser door or latch, or malfunctioning electronic components that control the dispensing process.

Symptoms of a bad dispenser include:

• Improper dispensing of detergent or rinse aid
• Insufficient cleaning or rinsing results
• Leaks or drips from the dispenser area
• The dispenser door not opening or closing correctly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rinse Aid Cap is an OEM part for Whirlpool dishwashers. It is designed to securely cover the rinse aid dispenser, ensuring the proper release of rinse aid during the wash cycle to improve drying performance and prevent water spots on dishes.

Causes of a bad rinse aid cap can include wear and tear over time, damage from accidental mishandling, or loss of the cap. Without a properly functioning cap, the rinse aid may not dispense correctly.

Symptoms of a bad rinse aid cap include:

• Rinse aid leaking or not dispensing
• Water spots or streaks on dishes after drying
• The cap not fitting securely or being visibly damaged
• The rinse aid compartment remaining full or not using rinse aid as expected

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Actuator is an OEM part for Whirlpool dishwashers. This actuator is responsible for releasing detergent from the dispenser at the appropriate time during the wash cycle, ensuring effective cleaning of the dishes.

Causes of a bad detergent dispenser actuator can include electrical malfunctions, wear and tear from frequent use, or physical damage to the actuator mechanism.

Symptoms of a bad detergent dispenser actuator include:

• The detergent not dispensing during the wash cycle
• The dispenser door not opening
• Dishes not being cleaned properly due to no detergent release
• Error codes related to the dispenser

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This acoustic fiber is the sound-absorbing insulation used in a refrigerator's machine compartment. Replacing a missing or damaged pad reduces operating noise from the compressor area and helps maintain the unit's intended sound levels.

• Absorbs and dampens compressor and condenser fan noise from the rear machine compartment
• Helps reduce vibration resonance transmitted through the cabinet
• Restores sound control when original insulation is torn, saturated, or missing
• Common symptoms: increased humming, buzzing, or rattling from the back or bottom of the refrigerator

• Disconnect power and pull the refrigerator forward for rear access
• Remove the lower rear access panel and note the insulation's placement/orientation
• Position the new pad in the same location; keep clear of coils, wiring, airflow paths, and moving parts
• Reinstall the access panel and restore power; verify no contact or obstruction

This wax motor is the actuator for the dishwasher's rinse aid dispenser, releasing rinse agent at the correct time in the cycle. Replacing a weak or failed unit restores consistent rinse aid dispensing and helps minimize spotting.

• Actuates the rinse aid dispenser by extending a plunger when energized
• Works with the control to meter rinse aid during the final rinse
• Failure symptoms can include rinse aid not dispensing, the level never dropping, and increased spotting/filming on dishes
• Dispenser may remain closed with no audible actuation during the cycle

• Disconnect power at the breaker and shut off water before servicing
• Remove the door panel to access the dispenser; label and disconnect wires
• Release the old motor and install the new one in the same orientation, ensuring it seats fully
• Run a test cycle to ensure the dispenser releases rinse aid

Note: Check Serial Number for correct part

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is the lower access panel for the appliance's base. It finishes the front opening and shields internal components, helping reduce noise and keep dust and debris away from the motor and wiring.

• Covers the lower service opening beneath the door to provide a clean, finished look
• Helps protect internal components from debris and accidental contact
• Can reduce vibration noise when properly secured
• Replace if the panel is bent, cracked, rusted, missing, or rattles/doesn't stay secured

• Disconnect power; also shut off the water supply
• Support the existing panel while removing mounting screws; retain hardware for reuse
• Position the new panel, align with mounting holes/slots, and reinstall screws—do not overtighten
• Confirm door clearance and that the panel sits flush without interference

This wet agent dispenser replaces the washer's liquid fabric softener dispenser to restore proper dispensing during the rinse cycle. It helps keep softener contained until the machine is ready to release it, improving rinse-time performance. What it does:

• Holds and releases liquid fabric softener (wet agent) into the rinse cycle
• Ensures softener is delivered at the correct time for even distribution
• Stops leaking or premature release when the dispenser housing is intact
• Commonly replaced when the dispenser cracks, clogs, or fails to dispense

• Disconnect power to the appliance before starting any repairs
• Access method varies by model; remove dispenser drawer or top panel per your model's service instructions
• Inspect surrounding seals and clips; replace if damaged to prevent leaks