Turn Line Mover Carburetor Gasket Parts

• Leaking

The dishwasher is 4 years old, so I figured since it was leaking from the bottom, replacing the Tub Gasket PN: AP5690109, Splash Shield Kit PN: AP4338941 , and the bottom Door Seal/Gasket PN: AP5809675 was a good idea; the machine probably has around 1200 cycles in 4 years. There's no telling how much the door had opened and closed!? The bottom Door Seal/Gasket was badly worn, and the entire job took me around 30 minutes which included the detailed cleaning of the mating flanges. Take your... Read more

We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more

This door gasket presses into slot around door pull off old and press in new a five minute repair Read more

We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more

• Frost buildup

Frost & ice were building up inside the top of our upright freezer, so I replaced the door gasket. First I'll make my long story short, then I'll tell the longer story for those who might be interested and might benefit from my experience. Short version - The whole project took about three hours, but less than an hour of that would have been required if I were more of a handyman and if the freezer hadn't had prior work done on the door for the same frost buildup problem. Long version - When... Read more

The dishwasher is 4 years old, so I figured since it was leaking from the bottom, replacing the Tub Gasket PN: AP5690109, Splash Shield Kit PN: AP4338941 , and the bottom Door Seal/Gasket PN: AP5809675 was a good idea; the machine probably has around 1200 cycles in 4 years. There's no telling how much the door had opened and closed!? The bottom Door Seal/Gasket was badly worn, and the entire job took me around 30 minutes which included the detailed cleaning of the mating flanges. Take your... Read more

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

I went to your web sight. I entered the GE dishwasher model # and found the gasket was available. While looking up the needed gasket I happened to see an applicable how-to replace the gasket video and watched it. It was easy to follow and VERY helpful. As I watched, I wrote down the gasket replacement procedure step-by-step. I ordered the needed gasket and received it in 2 days (AMAZING). The replacement entailed disconnecting the water supply, the power supply and the discharge hose. I removed... Read more

Very easy to do. Read more

Thanks to Jason and his tech people at Appliance Parts Pro, I was able to remove and replace the seal and eliminate all leaks at the bottom of the door. I have a Kitchenaide (Whirlpool) dishwasher model KUDC10IXBL1. Here is how to replace the bottom door seal. 1) Shut off breaker to dishwasher on the electrical panel. 2) Open the dishwasher door completely, and while supporting the door, remove the hex head screws that hold the outside cover. 2) Close the door carefully and slip the outside... Read more

I ordered door seal and bottom strip seal: GASKET TUB PLASTIC Number: WD08X22094 GASKET BEACH PLASTIC: WD08X21894 I had done this once previously and removed the door. That was not too bad but trying to put the door back on the hinges by myself was a bit of work. This time I: 1) removed the 2 screws at the bottom of the door. 2) opened the door all the way 3) slowly pulled the door back on the hinges till I could pull out the bottom gasket 4) slid the new gasket back in place 5) pushed the... Read more

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

• Marks left on clothes

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

Walk into the kitchen on 21 Sep. Eight year old Frigidaire refrigerator appears to be short cycling, controls are nonfunctional. Unplug it for a few minutes, plug it back in, appears to return to normal function. Return to kitchen half hour 45 minutes later it's short cycling again. Panel has codes on it (S or 5 E CE, later that changes to S or 5 Y CE). Research of codes says replace main board and control board. Not sure where this main board is. 22 Sep call appliance repair. "Soonest... Read more

A quick google search lead me to the problem - the plastic door gasket had become loose and broken. Received the part very quickly and installed it that night after a little trial and error. What the videos don't tell you is that to properly 'seat' the gasket you need to angle it UP when you push it into the little gap. If you angle it up, it will catch and seat properly, if you just push it in normally, it won't catch on the right part and it'll just hang loose at the bottom of the door and... Read more

Found the entire top bearing support plastic piece was completely worn through, the bearing slides had all disappeared some time ago. So it was obviously the problem. The felt trap duct (which is actually a drum seal along bottom front of drum so I don't know why they call it felt trap duct) had also disappeared, so a lot of lint was getting inside the front panel too. It's a very easy repair to change the bearing support; everything just pops out just like the video shows. Make sure you... Read more