Parts for Roper RTW4740YQ0: 03 - Basket And Tub Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Agitator Cap is an OEM part for Whirlpool washing machines. It fits on top of the agitator and helps secure the agitator components, ensuring proper functioning during the wash cycle. This cap is essential for maintaining the agitator's efficiency and preventing water from entering the agitator assembly.

Causes of a bad agitator cap can include wear and tear from regular use, cracking or damage from impacts, or degradation due to exposure to detergents and water over time.

Symptoms of a bad agitator cap include:

• The cap being loose or not fitting properly
• Water leaking into the agitator assembly
• Excessive noise during the wash cycle
• Reduced agitation performance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This Inner Cap is an OEM replacement part for Whirlpool washers that is responsible for keeping water, fabric softener, and debris from getting into the agitator assembly. The cap is located at the top of the agitator to protect the agitator's internal parts. Fabric softener dispenses through the holes in the agitator above the cap.

Description- For the O ring seal only order WPW10072840.

This part fixes the following symptoms-

• Water leakage from the agitator.
• Fabric softener not dispensing correctly.
• Poor washing performance.
• Unusual noises during agitation.
• Excessive wear on clothes.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Whirlpool top load washer agitator inner cap seal is an OEM replacement part responsible for providing a tight seal and preventing water from leaking in to the agitator. The inner cap seal is located underneath the agitator cap at the top of the agitator assembly.

Over time, the Inner Cap Seal can become worn, cracked, or damaged due to repeated exposure to water, detergents, and the high-speed spinning of the tub. A faulty seal can lead to water leaks, excessive noise, and potential damage to other components.

This part fixes the following symptoms:

• Water leaking from the agitator assembly during operation
• Excessive splashing or spraying of water during the wash cycle
• The agitator not moving or agitating properly
• Visible wear, tears, or damage to the inner cap seal
• Difficulty in removing or reattaching the agitator assembly

The Whirlpool inner cap seal can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Washplate Bolt is an OEM part for Whirlpool washing machines. This bolt is designed to secure the washplate to the washer's drive shaft, ensuring stable and effective agitation during the wash cycle.

Causes of a bad washplate bolt can include stripping or wearing out from regular use, corrosion from exposure to water and detergents, or damage due to over-tightening or improper installation. A faulty bolt can compromise the washplate's stability and affect the washing machine's performance.

Symptoms of a bad washplate bolt include:

• The washplate being loose or wobbling during operation
• Unusual noises such as rattling or clunking during the wash cycle
• Poor cleaning performance due to ineffective agitation
• The washplate detaching from the drive shaft

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Agitator Bolt Washer is an OEM part for Whirlpool washing machines. It sits beneath the agitator bolt, providing a secure and tight seal to ensure the agitator remains firmly attached to the drive shaft. This washer plays a crucial role in the smooth and effective operation of the agitator during the wash cycle.

You should replace this agitator bolt washer if it becomes worn out, cracked, or lost. Causes of a bad washer can include regular wear and tear, exposure to harsh detergents, or high levels of agitation that can degrade the material over time.

Symptoms of a bad agitator bolt washer include:

• The agitator being loose or wobbling during the wash cycle
• Unusual noises coming from the agitator area
• Ineffective washing performance
• The agitator not staying in place

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Complete Agitator Assembly is an OEM part for Whirlpool washing machines. This assembly includes the central vertical agitator component along with the retainer ring. Together they are responsible for the agitation and rubbing motions that work to remove soils and stains from clothing during wash cycles.

Causes of a bad agitator assembly can include wear and tear leading to wobbly or loose motions, cracks in plastic components from repeated impacts, or corrosion of metal components.

Symptoms of a bad complete agitator assembly include:

• Vibration or shaking issues during agitation
• Improper or lack of agitating of clothes
• An agitator that is difficult to rotate by hand
• Cracks, missing pieces or corrosion visible upon inspection

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The medium cam agitator repair kit is an OEM part for Whirpool washers. It includes 4 agitator dogs, a medium length cam, a cap seal, a washer for the agitator bolt, and a thrust washer.

Symptoms of a bad part:

• The agitator not working or turning
• Loud grinding or clicking noises during the wash cycle
• Clothes not being thoroughly cleaned or rinsed

Causes of a faulty agitator system can include normal wear and tear over time, exposure to excessive loads or unbalanced loads, or physical damage due to impact or mishandling.

Whirlpool recommends using a small amount of grease with this kit (if no grease is present on the old thrust washer). For the Whirlpool agitator grease, order 350849. For the long cam, order 285748. For the short cam, order 285809. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Washer Agitator Dog set is a set of 4 OEM replacement parts for Whirlpool and Kenmore washing machines, designed to engage the agitator, allowing it to move in one direction and lock in the opposite direction. The agitator dogs also come available in the agitator repair kit WP8537433. Check your model number for compatibility.

Symptoms of failing Agitator Dogs include:

• The agitator not moving
• Only moving in one direction
• Clothes not getting cleaned due to lack of agitation
• Clothes becoming tangled

Causes of bad Agitator Dogs can range from normal wear and tear, which gradually erodes their teeth, making them too smooth to engage the agitator properly, to overloading the washing machine, which puts extra stress on the agitator and accelerates the wear of the dogs.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This small bearing supports the driven cam within the mechanism, ensuring smooth rotation and consistent actuation. Replace it if the original bearing wears, cracks, or binds to restore reliable, quieter operation.

• Provides a low-friction pivot point for the driven cam
• Keeps the cam aligned for accurate, repeatable actuation
• Reduces friction, wear, and squeaking/grinding noises from the cam assembly
• Common symptoms include sticking/binding motion, noisy operation, inconsistent actuation, or visible bearing damage

• Disconnect power to the appliance; turn off water supply if applicable
• Access the cam assembly and note the orientation of parts
• Seat the new bearing fully and reuse any original retainers/spacers as required
• Manually rotate the cam to verify smooth movement before reassembly and testing

This upper agitator—also called the clothes mover—is the top section of the agitator in select top-load washers. It works with the agitator cam and dogs to roll laundry over during wash strokes. Replace if cracked, stripped, or no longer engaging. What it does:

• Provides the upper vanes that lift and roll clothes for proper turnover during agitation
• Transfers one-way motion from the cam/dogs to the top section of the agitator
• Helps address symptoms like the top section free-spinning, poor turnover/cleaning, rattling/loose feel, or visible cracks/broken fins

• 1 upper agitator (clothes mover)

• Unplug the washer and turn off water before servicing
• Remove the dispenser and cap to access the center fastener; lift out the agitator assembly
• Separate the old upper section from the cam, seat the new clothes mover fully on the splines, and reassemble
• Hand-check for one-way engagement of the top section before running a test cycle

The Thrust Washer is an OEM part for Whirlpool washing machines, specifically designed to reduce friction between the moving parts of the washer's transmission system. This small but crucial component is placed between the rotating and stationary parts, allowing for smooth movement and preventing wear and tear on the transmission.  

Causes for a Thrust Washer to fail include regular wear and tear from the mechanical stress of washing cycles, improper alignment or installation that can lead to uneven wear, and the accumulation of debris or corrosion that can interfere with its function. 

Symptoms of a bad Thrust Washer include:

• The washing machine makes unusual noises during operation 
• The washer struggles to switch between cycles or fails to spin at the correct speed.
• Increased vibration or shaking of the washing machine

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Agitator Base is an OEM part for Whirlpool washing machines. This component is located at the bottom of the agitator assembly and is responsible for supporting the agitator while it moves clothes during the wash cycle. This is the bottom half of the agitator. For a complete agitator search by your model. If your model does not list one you can order 285565

Over time, the agitator base can wear out or become damaged due to constant use, heavy loads, or exposure to harsh detergents. A compromised agitator base can lead to inefficient washing and potential damage to other parts of the washer.

Symptoms of a bad agitator base include:

• The agitator not moving properly or becoming loose
• Unusual noises during the wash cycle
• Clothes not being cleaned effectively
• The washer shaking or vibrating excessively

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This washer tub ring, sometimes called a tub cover, snaps onto the outer tub to contain splashing and guide water back into the basket. Replacing a cracked or loose ring helps reduce top-side leaks and protects fabrics at the tub opening. What it does:

• Forms the molded upper edge of the outer tub and acts as a splash guard
• Helps direct water back into the basket during wash and spin
• Maintains proper clearance at the tub rim to prevent fabric snags
• Common signs of failure: visible cracks/broken tabs, loose fit, or water splashing/leaking from under the lid/top

• 1 tub ring

• Disconnect power and turn off water; wear cut-resistant gloves
• Raise or open the top to access the tub opening
• Release the retaining clips/tabs and detach any connected hoses from the old ring
• Align and press the new ring evenly until all tabs fully engage; verify an even, secure fit before reassembly

The Spanner Nut is an OEM part for Whirlpool washing machines. This nut secures the washer tub to the drive shaft, ensuring that the tub remains stable during the wash and spin cycles. Properly securing the tub is crucial for the machine's performance and longevity, as it helps maintain balance and reduce vibrations.

You should replace the spanner nut if it becomes loose or stripped. Causes of a bad spanner nut can include over-tightening, regular wear and tear, or damage from heavy loads. Exposure to moisture and detergent over time can also lead to corrosion, compromising the nut's ability to secure the tub effectively.

Symptoms of a bad spanner nut include:

• Excessive vibrations or shaking during the wash cycle
• Loud banging or knocking noises
• The washer tub being loose or misaligned
• Leaks around the tub area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Tool for removing the spanner nut - TB123B.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Washer Drive Block is an OEM part for Whirlpool washing machines. This component is situated between the washer's transmission and the inner tub, playing a key role in transferring the rotational motion from the motor to the tub. 

Causes for replacement often stem from normal wear and tear, which can lead to the drive block becoming worn or damaged. This wear can prevent the drive block from properly engaging with the tub, leading to inefficient cycles and potential damage to other parts of the washing machine.

Symptoms of a bad Washer Drive Block include:

• The washer tub has difficulty agitating or spinning.
• A loud noise during the spin cycle, indicating that the tub is not engaging correctly with the transmission.
• The machine vibrates excessively or seems off-balance, even with a balanced load.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This outer tub is the main water-holding housing for a top-load washing machine. It supports the inner basket and seals the wash chamber, helping the washer contain water and direct proper wash action. What it does:

• Holds wash water and surrounds the inner basket during fill, wash, and rinse cycles
• Supports the inner tub and transmission/agitator assembly for stable operation
• Prevents leaks by maintaining the sealed wash chamber; a cracked tub can cause visible water under the machine
• Helps reduce noise and vibration by keeping the wash components aligned

• One outer tub

• Disconnect power and water supply before beginning any repair
• Drain any remaining water from the tub and remove the washer cabinet or top to access the tub
• Transfer any components (basket, agitator, seals, mounting hardware) only if explicitly listed in your parts list; replace worn seals and gaskets when reinstalling

The Tub Seal is an OEM part for Whirlpool washing machines. Located between the outer tub and inner basket, it forms a barrier preventing leaks that could damage surrounding components and structures.

Causes of a bad tub seal can be cracks or compression failures due to repetitive impacts and stresses from continual clothes tumbling. Detergents and temperature fluctuations also break down rubber over decades when exposed to laundry environments.

Symptoms of a bad tub seal include: 

• Water leakage noticed around the base of the washer cabinet
• Reduced or inefficient cleaning from leaking wash water 
• Potential water damage risks to floors and home infrastructure

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

The Suspension Bearing Kit is an OEM part for Whirlpool washing machines. It is designed to support the tub assembly and ensure smooth, stable operation during the wash cycle. The kit includes bearings and other components that help absorb vibrations and reduce noise, contributing to the longevity and efficiency of the machine. The 8-piece set has 4 types of suspension rod supports made of strong plastic and about 1.5 inches in diameter. 

Symptoms of a bad Suspension Bearing Kit include:

• Unusual noise during the spin cycle,
• Excessive vibration or "walking" of the washer,
• The washing machine drum sagging or appearing off-balance.

Causes of suspension bearing failure often involve wear and tear from regular use, overloading of the machine, or inadequate maintenance leading to deterioration of parts.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This tie wire secures wiring and small components to a tree-style mounting post, helping keep harnesses organized and preventing chafing or loose connections. Durable metal construction holds wiring in place for reliable operation. What it does:

• Secures wiring bundles and small components to a tree-style mount or post
• Helps prevent wires from rubbing against sharp edges or vibrating loose
• Reduces risk of intermittent electrical connections caused by loose harnesses
• Keeps internal wiring organized for safer, cleaner repairs

• Tie wire

• Disconnect power and unplug the appliance before servicing
• Position wires on the tree mount and wrap or fasten the tie wire
• Trim or bend any sharp ends to avoid contact with other parts or wiring
• Replace if damaged, corroded, or no longer holds wiring securely

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.