Parts for Whirlpool 7EWTW1509YM0: 03 - Basket And Tub Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This fabric softener cup snaps into the washer dispenser assembly to hold and release liquid softener during the rinse cycle, helping fabric softener dispense where and when it's needed for cleaner, softer laundry. What it does:

• Holds liquid fabric softener until the washer's rinse cycle
• Releases softener at the correct time so it mixes with rinse water
• Prevents softener from dispensing during the wash cycle
• Helps reduce staining or over-dispensing when installed correctly

• Turn off and unplug the washer before servicing to avoid shock or injury
• Remove the dispenser drawer or access panel per your model's service instructions to replace the cup
• Inspect surrounding seals and guides; replace any damaged clips or gaskets for proper fit

This Inner Cap is an OEM replacement part for Whirlpool washers that is responsible for keeping water, fabric softener, and debris from getting into the agitator assembly. The cap is located at the top of the agitator to protect the agitator's internal parts. Fabric softener dispenses through the holes in the agitator above the cap.

Description- For the O ring seal only order WPW10072840.

This part fixes the following symptoms-

• Water leakage from the agitator.
• Fabric softener not dispensing correctly.
• Poor washing performance.
• Unusual noises during agitation.
• Excessive wear on clothes.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Whirlpool top load washer agitator inner cap seal is an OEM replacement part responsible for providing a tight seal and preventing water from leaking in to the agitator. The inner cap seal is located underneath the agitator cap at the top of the agitator assembly.

Over time, the Inner Cap Seal can become worn, cracked, or damaged due to repeated exposure to water, detergents, and the high-speed spinning of the tub. A faulty seal can lead to water leaks, excessive noise, and potential damage to other components.

This part fixes the following symptoms:

• Water leaking from the agitator assembly during operation
• Excessive splashing or spraying of water during the wash cycle
• The agitator not moving or agitating properly
• Visible wear, tears, or damage to the inner cap seal
• Difficulty in removing or reattaching the agitator assembly

The Whirlpool inner cap seal can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Washplate Bolt is an OEM part for Whirlpool washing machines. This bolt is designed to secure the washplate to the washer's drive shaft, ensuring stable and effective agitation during the wash cycle.

Causes of a bad washplate bolt can include stripping or wearing out from regular use, corrosion from exposure to water and detergents, or damage due to over-tightening or improper installation. A faulty bolt can compromise the washplate's stability and affect the washing machine's performance.

Symptoms of a bad washplate bolt include:

• The washplate being loose or wobbling during operation
• Unusual noises such as rattling or clunking during the wash cycle
• Poor cleaning performance due to ineffective agitation
• The washplate detaching from the drive shaft

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Agitator Bolt Washer is an OEM part for Whirlpool washing machines. It sits beneath the agitator bolt, providing a secure and tight seal to ensure the agitator remains firmly attached to the drive shaft. This washer plays a crucial role in the smooth and effective operation of the agitator during the wash cycle.

You should replace this agitator bolt washer if it becomes worn out, cracked, or lost. Causes of a bad washer can include regular wear and tear, exposure to harsh detergents, or high levels of agitation that can degrade the material over time.

Symptoms of a bad agitator bolt washer include:

• The agitator being loose or wobbling during the wash cycle
• Unusual noises coming from the agitator area
• Ineffective washing performance
• The agitator not staying in place

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is the upper agitator (auger) assembly for top-load washers. It restores the one-way ratcheting action that pulls laundry downward during the wash stroke for proper rollover and cleaning performance. What it does:

• Drives the top half of a dual-action agitator to move clothes down in the tub
• Replaces a worn or stripped auger that lets the top agitator stop or slip
• Helps resolve weak agitation or poor clothes rollover
• Addresses clicking/grinding from worn internal ratchet components

• 1 agitator auger assembly

• Disconnect power before servicing
• Remove the fabric softener dispenser and agitator cap, then the agitator bolt
• Lift off the old auger, align splines, and seat the new auger on the lower agitator
• Reinstall the bolt and caps; run a short wash to confirm proper agitation

This dishwasher cam assembly is a precision-molded drive component that converts rotation into the timed movement the mechanism needs. Replacing a worn cam helps restore smooth, reliable actuation during the cycle and reduces sticking or misalignment.

• Converts rotational input into precise motion for the linked latch/actuator mechanism
• Maintains proper timing and engagement so the mechanism operates when commanded
• Wear or cracking can lead to slipping, binding, or incomplete travel
• Typical symptoms: associated action fails to engage/release at the right time, intermittent operation, or clicking/grinding noises from the mechanism

• Disconnect power at the breaker and shut off water before servicing
• Access the mechanism; note cam orientation and linkage positions
• Transfer any reusable pins/springs; install the new cam in the same orientation
• Run a test cycle to ensure proper operation and check for leaks or abnormal noises

The Washer Agitator Dog set is a set of 4 OEM replacement parts for Whirlpool and Kenmore washing machines, designed to engage the agitator, allowing it to move in one direction and lock in the opposite direction. The agitator dogs also come available in the agitator repair kit WP8537433. Check your model number for compatibility.

Symptoms of failing Agitator Dogs include:

• The agitator not moving
• Only moving in one direction
• Clothes not getting cleaned due to lack of agitation
• Clothes becoming tangled

Causes of bad Agitator Dogs can range from normal wear and tear, which gradually erodes their teeth, making them too smooth to engage the agitator properly, to overloading the washing machine, which puts extra stress on the agitator and accelerates the wear of the dogs.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This driven cam bearing supports the cam in the compactor's drive assembly, reducing friction and keeping components aligned so the ram moves smoothly and the unit completes and reverses cycles reliably.

• Supports and centers the driven cam/gear for proper alignment
• Reduces friction and wear for smoother cam rotation
• Helps ensure correct switch timing so the ram reverses at end of travel
• Symptoms of wear include squealing/grinding, binding or jerky ram movement, or failure to complete a cycle

• Disconnect power at the breaker or unplug the unit before servicing
• Secure the drawer/ram to prevent unintended movement while working
• Access the drive mechanism and note the bearing's orientation on the cam before removal
• Seat the new bearing fully and hand-rotate the cam to verify smooth movement before reassembly and restoring power

This auger agitator moves ice through the refrigerator dispenser so cubes and crushed ice flow smoothly to the user. It replaces a worn or damaged auger to restore normal dispensing performance. What it does:

• Rotates inside the dispenser chute to push ice toward the dispenser outlet
• Helps prevent ice clumping and improves consistent dispensing
• Commonly replaced when ice won't dispense, dispenses slowly, or makes grinding noises
• Compatible with models that use a motor-driven auger assembly

• Disconnect power to the refrigerator before starting any repairs
• Remove the dispenser cover and ice bucket per your model's service instructions to access the auger
• Inspect for ice jams or broken plastic fragments before installing the new auger

This thrust spacer positions and supports the washer tub assembly, keeping rotating parts aligned to reduce wear and maintain smooth operation. It's a small but important part for proper drivetrain alignment in top-load washers. What it does:

• Centers and spaces the tub or agitator relative to the gearbox/shaft to prevent metal-on-metal contact
• Helps maintain correct clearance for smooth spin and agitation
• Can reduce noise and vibration caused by misalignment
• Commonly replaced when wear or damage causes rubbing, grinding, or poor spinning performance

• One thrust spacer

• Designed for use with compatible washer assemblies; follow your model's service manual for fitment and orientation
• Disconnect power and water supply before servicing the washer
• Inspect adjacent seals, bearings, and shaft components while replacing the spacer; replace any worn parts

This is the central agitator that fits over the drive shaft in a top-load washer to move clothing through the wash water. Replacing a worn agitator restores proper wash action, improving turnover and cleaning performance.

• Rotates and oscillates to circulate laundry, lifting and rolling items through detergent and water
• Common failure signs include poor or no agitation, clothes not moving, or longer-than-normal wash times
• Built with a durable poly/TPE body for consistent grip on fabrics and smooth operation

• Disconnect power and water; use proper PPE
• Remove the fabric softener cap and agitator bolt to lift the old agitator straight off
• Inspect splines and drive components; transfer or replace fasteners as required
• Seat the new agitator fully and tighten the bolt to manufacturer guidance; test for secure engagement

This washer tub ring, sometimes called a tub cover, snaps onto the outer tub to contain splashing and guide water back into the basket. Replacing a cracked or loose ring helps reduce top-side leaks and protects fabrics at the tub opening. What it does:

• Forms the molded upper edge of the outer tub and acts as a splash guard
• Helps direct water back into the basket during wash and spin
• Maintains proper clearance at the tub rim to prevent fabric snags
• Common signs of failure: visible cracks/broken tabs, loose fit, or water splashing/leaking from under the lid/top

• 1 tub ring

• Disconnect power and turn off water; wear cut-resistant gloves
• Raise or open the top to access the tub opening
• Release the retaining clips/tabs and detach any connected hoses from the old ring
• Align and press the new ring evenly until all tabs fully engage; verify an even, secure fit before reassembly

The Spanner Nut is an OEM part for Whirlpool washing machines. This nut secures the washer tub to the drive shaft, ensuring that the tub remains stable during the wash and spin cycles. Properly securing the tub is crucial for the machine's performance and longevity, as it helps maintain balance and reduce vibrations.

You should replace the spanner nut if it becomes loose or stripped. Causes of a bad spanner nut can include over-tightening, regular wear and tear, or damage from heavy loads. Exposure to moisture and detergent over time can also lead to corrosion, compromising the nut's ability to secure the tub effectively.

Symptoms of a bad spanner nut include:

• Excessive vibrations or shaking during the wash cycle
• Loud banging or knocking noises
• The washer tub being loose or misaligned
• Leaks around the tub area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Tool for removing the spanner nut - TB123B.

This silverware basket replaces a cracked, broken, or rusted utensil holder so forks, knives and spoons stay upright and separate for better cleaning and safe unloading. Easy to snap into the dishwasher lower rack. What it does

• Holds silverware and small dishwasher-safe items securely during wash cycles.
• Keeps utensils separated to reduce nesting and improve water circulation and cleaning.
• Replaces baskets with broken tabs, holes, or rust that allow utensils to fall through.
• Helps prevent scratches by keeping metal utensils contained and away from delicate items.

• Disconnect the dishwasher from power before servicing.
• Slides into the lower rack location; no tools usually required.
• Inspect rack tracks and support clips; replace if damaged to ensure proper fit.
• Handle edges carefully if basket is damaged to avoid cuts; dispose of failed basket properly.

The Washer Drive Block is an OEM part for Whirlpool washing machines. This component is situated between the washer's transmission and the inner tub, playing a key role in transferring the rotational motion from the motor to the tub. 

Causes for replacement often stem from normal wear and tear, which can lead to the drive block becoming worn or damaged. This wear can prevent the drive block from properly engaging with the tub, leading to inefficient cycles and potential damage to other parts of the washing machine.

Symptoms of a bad Washer Drive Block include:

• The washer tub has difficulty agitating or spinning.
• A loud noise during the spin cycle, indicating that the tub is not engaging correctly with the transmission.
• The machine vibrates excessively or seems off-balance, even with a balanced load.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This outer tub is the main water-holding housing for a top-load washing machine. It supports the inner basket and seals the wash chamber, helping the washer contain water and direct proper wash action. What it does:

• Holds wash water and surrounds the inner basket during fill, wash, and rinse cycles
• Supports the inner tub and transmission/agitator assembly for stable operation
• Prevents leaks by maintaining the sealed wash chamber; a cracked tub can cause visible water under the machine
• Helps reduce noise and vibration by keeping the wash components aligned

• One outer tub

• Disconnect power and water supply before beginning any repair
• Drain any remaining water from the tub and remove the washer cabinet or top to access the tub
• Transfer any components (basket, agitator, seals, mounting hardware) only if explicitly listed in your parts list; replace worn seals and gaskets when reinstalling

The Tub Seal is an OEM part for Whirlpool washing machines. Located between the outer tub and inner basket, it forms a barrier preventing leaks that could damage surrounding components and structures.

Causes of a bad tub seal can be cracks or compression failures due to repetitive impacts and stresses from continual clothes tumbling. Detergents and temperature fluctuations also break down rubber over decades when exposed to laundry environments.

Symptoms of a bad tub seal include: 

• Water leakage noticed around the base of the washer cabinet
• Reduced or inefficient cleaning from leaking wash water 
• Potential water damage risks to floors and home infrastructure

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

The Suspension Rod Kit is an OEM replacement part for Whirlpool washing machines, designed to provide support and stability to the washer drum. This kit includes four suspension rods that connect the washing machine drum to the frame, allowing for controlled movement and reducing vibration during the spin cycle. These rods play a critical role in absorbing the motion of the washer drum, ensuring smooth operation and preventing excessive noise or movement that could damage the machine or affect its performance.

Causes of these issues often stem from normal wear and tear, as the suspension rods can become worn out or damaged over time. Heavy or uneven loads can also put extra stress on the rods, leading to premature failure.

Symptoms of a bad part:

• Excessive noise or vibration during operation
• Shaking or movement of the washer
• Unevenly washed clothes or excessive wrinkles

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Suspension Bearing Kit is an OEM part for Whirlpool washing machines. It is designed to support the tub assembly and ensure smooth, stable operation during the wash cycle. The kit includes bearings and other components that help absorb vibrations and reduce noise, contributing to the longevity and efficiency of the machine. The 8-piece set has 4 types of suspension rod supports made of strong plastic and about 1.5 inches in diameter. 

Symptoms of a bad Suspension Bearing Kit include:

• Unusual noise during the spin cycle,
• Excessive vibration or "walking" of the washer,
• The washing machine drum sagging or appearing off-balance.

Causes of suspension bearing failure often involve wear and tear from regular use, overloading of the machine, or inadequate maintenance leading to deterioration of parts.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Suspension Bearing Kit is an OEM part for Whirlpool washing machines. It is designed to support the tub assembly and ensure smooth, stable operation during the wash cycle. The kit includes bearings and other components that help absorb vibrations and reduce noise, contributing to the longevity and efficiency of the machine. The 8-piece set has 4 types of suspension rod supports made of strong plastic and about 1.5 inches in diameter. 

Symptoms of a bad Suspension Bearing Kit include:

• Unusual noise during the spin cycle,
• Excessive vibration or "walking" of the washer,
• The washing machine drum sagging or appearing off-balance.

Causes of suspension bearing failure often involve wear and tear from regular use, overloading of the machine, or inadequate maintenance leading to deterioration of parts.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This washer water level pressure switch senses air pressure from the tub and signals the control to stop the fill at the correct point, helping prevent overfilling and ensuring each cycle uses the right amount of water. What it does:

• Monitors tub water level via the air dome hose and internal diaphragm
• Sends signals to the control to open/close the inlet valves during fill
• Helps match water level to the selected or programmed setting
• Failure symptoms include overfilling/overflow, continuous filling, low or no fill, or cycles not advancing from the fill stage

• One pressure switch

• Disconnect power and turn off the water supply before servicing
• Access the console/control area; note wire and hose positions before removal
• Transfer the air tube and wiring to the new switch; seat the tube fully and ensure it isn't kinked, cracked, or clogged
• Reassemble and run a quick fill test to ensure the valve shuts off at the proper level

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This spring retainer secures a tension spring within the mechanism so it stays aligned and under proper tension. Replacing a damaged retainer restores smooth, reliable movement and helps prevent the spring from detaching or wearing nearby parts. What it does:

• Anchors and guides the spring to maintain correct tension and alignment
• Helps prevent the spring from popping loose or chafing nearby components
• Can address issues like weak return action, uneven movement, or a mechanism that won't stay in position
• Direct replacement for a broken, cracked, or missing retainer

• 1 spring retainer

• Disconnect power; for water-bearing appliances, also turn off the water supply
• Carefully release spring tension; wear gloves and eye protection
• Note spring routing/orientation before removal for accurate reassembly
• Ensure the retainer is fully seated before restoring tension and testing operation

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.