Parts for Kenmore 110.75212610 (11075212610, 110 75212610): Cabinet Parts

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

10 - 16 x 1/2

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Color: White.

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

The Dryer Door Switch is an OEM replacement part for Whirlpool dryers. It is a crucial safety component that monitors the opening and closing of the dryer door, preventing the dryer from operating when the door is open.

Symptoms of a faulty Dryer Door Switch include:

• The dryer failing to start or operate with the door closed
• The dryer continuing to run or heat even when the door is open
• Error codes or warning lights related to the door switch sensor

Causes of a bad door switch can include normal wear and tear over time, physical damage from mishandling or impact, or electrical malfunctions.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

This electrical plug connects an appliance wiring harness to its mate, restoring a secure electrical connection to enable normal operation. Fits specific Whirlpool-designed connectors for targeted replacement when a connector is damaged or corroded. What it does

• Provides a secure mating point for a wiring harness to restore an interrupted circuit.
• Replaces cracked, melted, corroded, or loose connector ends that can cause intermittent power or component failures.
• Helps prevent arcing and poor contact that lead to overheating or erratic operation.
• Use when visual damage, burned contacts, or broken retaining features are found on the original plug.

• One replacement plug.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing electrical connectors.
• Verify connector orientation and seating; ensure mating terminals are clean and undamaged before installation.
• Use proper crimping or soldering and insulation methods per OEM guidance; avoid exposed conductors.

The Door Catch Bezel is an OEM replacement part for Whirlpool electric and gas dryers. It is located on the inner door frame and acts as the latching mechanism.  

Causes of a bad door catch can include wear and tear of the plastic tang and spring from years of repeated opening and closing of the dryer door. Over time, this limits its ability to fully engage and latch securely.

Symptoms of a bad dryer door catch include:

• Doors that do not fully close or seem loose when shut  
• Difficultly keeping the door tightly closed during cycles
• Unexpected opening of the door while running 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, and Admiral electric and gas dryers.

The Dryer Clip is an OEM component for Whirlpool electric and gas dryers. It securely fastens critical ductwork attached to the dryer cabinet. Over extended periods, the constant vibrations produced during tumbling cycles cause microscopic fractures or loosening within the clip material where it grips duct joints. 

Causes relate to ordinary fatigue from long-term resonance vibrations concentrated at anchoring points.

Symptoms involve:

• Loose or detached venting/ductwork affecting airflow
• Noticeable leaks emerging at separation interfaces
• Reduced drying effectiveness due to compromised ventilation

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This leveling leg threads into the base of the appliance to set height and keep it stable. Replacing a worn or missing leg helps eliminate rocking and vibration for quieter, smoother operation and proper alignment. What it does:

• Threads into the base to adjust height and level the appliance
• Stabilizes the cabinet to reduce rocking, vibration, and noise
• Helps maintain proper door alignment and smooth operation
• Replaces stripped, damaged, or missing leveling hardware

• 1 leveling leg

• Disconnect power; shut off water or gas supply if applicable
• Protect floors and use assistance to safely tip or lift the appliance
• Remove the old leg; thread the new leg by hand to avoid cross-threading, then adjust to level
• Ensure all legs contact the floor and the unit is stable after positioning

This gas surface burner head distributes fuel through its ports to create an even, reliable flame on your cooktop. Replace a clogged, damaged, or warped head to restore consistent ignition and proper heat on the affected burner.

• Channels gas through precision ports to produce a steady, even flame
• Interfaces with the surface igniter/electrode for quick, reliable ignition
• Replaces worn or clogged heads that cause weak, uneven, or yellow flames
• Helps resolve delayed ignition or a burner that won't light

• Disconnect electrical power and shut off gas supply before servicing
• Remove grate and burner cap, lift off the old head, and clean the mating surface
• Align the new head with the igniter and locating features; seat it fully before replacing the cap
• Restore gas and power; test ignition and verify proper flame pattern

Includes two bumpers and two locking clips. You will use one or the other depending on hole size.

The Dryer Door Catch is an OEM part for Whirlpool dryers. It keeps the dryer door securely closed during operation.

A bad door catch can occur due to regular use, wear and tear, or accidental damage. If you notice that the dryer door is not staying closed or is popping open during the drying cycle, it may indicate a problem with the door catch.

Symptoms of a bad door catch include:

• The dryer door not staying closed  
• Difficulty in properly latching the door shut
• Loud banging noises or vibrations 

Replace your faulty dryer door catch with this genuine OEM part to restore your dryer door. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This replacement door strike provides the solid catch point the latch/lock grabs so the appliance recognizes the door or lid is closed and can run safely. A worn, bent, or broken strike can interrupt operation. What it does

• Forms the fixed catch for the door/lid latch or lock
• Helps actuate the interlock/safety switch so a cycle can start
• Misalignment or damage can keep the door from latching and stop cycles
• Common symptoms: door/lid won't latch or stay closed, unit won't start, "Door/Lid" or "Lock" message, needing to hold the door shut, visible cracks or wear on the strike

• 1 strike

• Disconnect power to the appliance before servicing
• Open the door/lid and remove the mounting screws securing the old strike; retain hardware if it is reused
• Position the new strike in the same orientation and tighten screws snugly; avoid over-tightening to prevent damage
• Close and open the door/lid to confirm smooth latch engagement, then run a brief test cycle

This inner door panel replaces a damaged or worn interior door surface to restore the door's appearance and structural support. It helps protect internal components and provides a clean interior finish for the appliance door. What it does:

• Covers the inside surface of the appliance door and protects inner components
• Restores a solid mounting surface for door glass or trim pieces
• Eliminates visible dents, cracks, or ripped liners that can trap debris
• Reduces rattling or movement caused by a compromised inner panel

• One inner door panel

• Disconnect power (and gas if applicable) before starting any repair
• Handle with care to avoid damaging paint or trim; glass may be attached—support it if present
• Remove door screws/fasteners to replace the inner panel; retain hardware for reassembly

This outer door panel replaces a damaged or worn refrigerator/freezer door outer shell to restore appearance and protect internal components. It fits the appliance's front and provides a finished surface for handles and trim. What it does:

• Replaces a dented, cracked or rusted outer door surface to improve appearance
• Protects inner liners, insulation and door-mounted components from damage
• Restores a proper mounting surface for handle, trim and hinge hardware
• Helps maintain door alignment and sealing when used with correct internal parts

• Some disassembly of trim, handle and hinge hardware is required; keep fasteners organized
• Follow OEM service manual steps for removing and reinstalling the door to avoid damage
• Disconnect power and empty door-mounted items before starting work
• If internal liners, insulation, or mounting hardware are damaged, replace those parts as needed for proper fit

The Dryer Door Handle is an OEM replacement part for Whirlpool dryers. This component serves as the primary point of contact for opening and closing the dryer door, allowing easy access to load and unload laundry.

Symptoms of a faulty dryer door handle include:

• Difficulty in opening or closing the dryer door
• Loose or wobbly handle movement
•  Handle becoming detached or falling off

Causes of needing to replace the dryer door handle can include normal wear and tear over time, physical damage from impact or mishandling, or issues with the handle's mounting points or attachment mechanisms.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

Note: If your original door seal was rubber, please note that the factory has changed this to a fiberglass seal. The factory also recommends adhesive part# WPY055980 to install. 

The Dryer Door Seal is an OEM part for Whirlpool dryers. It forms a tight seal around the dryer door, preventing heat and moisture from escaping during the drying cycle. This helps maintain optimal drying efficiency and protects the surrounding components from excess moisture.

Causes of a bad dryer door seal can include wear and tear from regular use, damage from repeated opening and closing of the door, or degradation due to exposure to high temperatures over time.

Symptoms of a bad dryer door seal include:

• Heat escaping from the dryer
• Longer drying times
• Moisture buildup around the dryer door
• Visible cracks or gaps in the seal

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

The Idler Pulley is an OEM part for Whirlpool dryers, responsible for maintaining the correct tension on the drive belt, allowing it to remain tight and aligned, preventing slipping and contributing to the consistent rotation of the drum during cycles.  

Symptoms of a bad Idler Pulley include:

• Squealing or squeaking noises  
• The dryer drum failing to turn 
• Excessive vibration or unusual sounds 

Causes of failure can range from normal wear and tear, which can lead to the pulley's bearing wearing out, to the accumulation of lint and debris causing the pulley to seize or function improperly. Additionally, a cracked or damaged pulley can lead to belt misalignment and slippage.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Fits all Whirlpool-made dryers (Whirlpool, Kenmore with prefix 110, Roper, KitchenAid, and Estate). Matching belt 341241 and rear support rollers 349241T. Whirlpool dryer repair manual 677818L.

The Drive Belt is an OEM replacement part for Whirlpool dryers. This essential component is responsible for transferring power from the dryer's motor to the drum, allowing it to spin and tumble the clothes during the drying cycle.

Symptoms of needing to replace the drive belt include:

• The dryer drum not spinning or rotating
• Loud squeaking or grinding noises during the drying cycle
• Excessive vibration or shaking from the dryer
• Clothes taking longer to dry or remaining damp

Causes of a faulty drive belt can include normal wear and tear over time, exposure to excessive heat or lint buildup, or physical damage due to impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

This 5/16-18 x 3/4 machine bolt replaces a missing or damaged fastener used to secure panels, brackets and components in many home appliances. It restores proper fit and helps stop rattling or loose parts. What it does:

• Secures panels, brackets or assemblies to maintain proper alignment and safe operation
• Restores clamping force where a stripped or missing bolt lets parts shift or vibrate
• Helps eliminate rattling, scraping or movement caused by loose fasteners
• Matches standard 5/16-18 coarse threads for direct replacement of the OEM bolt

• Disconnect power to the appliance before servicing to reduce shock and injury risk
• Start threads by hand to avoid cross-threading; tighten using the correct socket or wrench
• Do not overtighten; snug to manufacturer torque or until secure to avoid stripping threads
• If the original mating threads are damaged, inspect the receiving part and repair or replace as needed

The Motor Pulley is an OEM part for Whirlpool dryers, connects the dryer motor to the drum belt, enabling the drum to turn and efficiently dry your clothes. This pulley is crucial for the smooth operation of the dryer, ensuring that the belt is tensioned correctly and runs smoothly without slipping or causing wear.  

Causes of a bad Motor Pulley include wear and tear from regular use, a buildup of lint and debris that can interfere with its operation, or a malfunctioning dryer motor that puts undue stress on the pulley.

Symptoms of a bad Motor Pulley include:

• Unusual noises coming from the dryer, such as squeaking or grinding
• The dryer drum failing to turn even though the motor is running
• The dryer taking longer than normal to dry clothes, which can occur if the pulley is not providing proper tension to the belt

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A direct-replacement motor-drive assembly that powers the appliance's drive system to restore rotation and mechanical motion. Designed to return reliable drive performance and reduce symptoms caused by a failed motor. What it does

• Turns the drive shaft or agitator so the unit can rotate, agitate or circulate as designed
• Restores motor-driven functions when the original motor has failed or stopped running
• Stops common symptoms such as no rotation, no agitation, intermittent motor operation, or a motor that only hums
• Works as the core mechanical drive component for affected cycles that rely on motor power

• Disconnect power before servicing to avoid electrical shock.
• Access may require removing panels or covers; keep track of screws and mounting hardware.
• Inspect wiring connectors and mounts; replace damaged fasteners or wiring as needed.

This motor mount clamp secures the dishwasher's pump/motor assembly to its housing, keeping the motor stable and the seal tight. Replace a damaged clamp to help prevent leaks and reduce vibration or rattling noise.

• Secures the pump/motor assembly at the mount to prevent movement
• Helps maintain a watertight seal at the motor connection
• A failed clamp can lead to leaking from the base area
• May cause excessive vibration or rattling during operation

• Disconnect power and turn off the water supply before servicing
• Access the pump/motor from beneath; support the assembly to relieve tension
• Note clamp orientation; ensure the existing seal is properly seated and tighten the new clamp evenly
• After reassembly, run a short cycle and check for leaks

This belt shield assembly is a molded protective cover that helps guard the dryer's drive belt and pulley area from debris and accidental contact, keeping moving parts enclosed for safer, more reliable operation. What it does:

• Protects the drive belt and pulley from lint, clothing snags and foreign objects
• Helps prevent accidental contact with rotating parts that can cause wear or injury
• Can reduce rubbing or scraping noises caused by a damaged or shifted belt cover
• Visible cracks, breaks or a missing shield are common signs this part needs replacement

• Always unplug the appliance or disconnect power before servicing
• Basic hand tools are typically required; follow the OEM service manual for step-by-step removal and reinstallation
• Inspect the drive belt and pulley while the cover is removed and replace any worn components

This foam seal cushions and seals the icemaker area to reduce vibration and prevent air leaks that can affect ice quality and efficiency. It's a direct-fit replacement designed to restore proper sealing around the icemaker housing. What it does:

• Cushions the icemaker assembly to reduce noise and movement
• Helps seal gaps to limit warm air intrusion that can cause icemaking issues
• Supports consistent ice production by maintaining the intended airflow path
• Resists compression set for reliable sealing over time

• One foam seal for the icemaker housing

• Basic installation; remove power to the appliance before starting
• Align the seal to the icemaker housing, pressing into place until fully seated
• Inspect surrounding surfaces for debris or damage and clean before installing

This idler bracket supports the dryer's idler pulley and helps maintain proper belt tension so the drum turns smoothly. Replacing a worn bracket restores stable pulley alignment and reduces belt wear and noise. What it does:

• Holds the idler pulley in correct position to maintain belt tension and routing
• Prevents the idler from shifting or collapsing under load, which can cause belt slipping
• Helps eliminate squealing, rubbing, or uneven drum movement caused by a failed bracket
• Works with the idler pulley and belt to keep the dryer drum rotating efficiently

• Disconnect power before beginning any repair to avoid electrical shock.
• Access may require removing the dryer front or lower panel; support the drum/belt when removing tension.
• Inspect the idler pulley and belt for wear and replace if needed—bracket replacement alone may not fix pulley or belt issues.
• Use care around sheet metal edges and fasteners; follow OEM diagram for correct bracket orientation.

This poly-V blower belt links the motor to the blower wheel to move air through the appliance. Replacing a worn or broken belt restores proper airflow and helps maintain reliable drying/venting performance. What it does:

• Transfers motor rotation to the blower/impeller to circulate air
• Helps maintain proper airflow through the cabinet and exhaust
• Common failure signs include weak or no airflow at the vent, longer run times, or safety shutdown from poor airflow
• Physical clues: belt broken, frayed, glazed, stretched, or squealing from the blower area

• 1 poly-V blower belt

• Disconnect power and, if applicable, shut off gas supply before servicing
• Access varies by model; remove panels or blower cover to reach the belt
• Note routing; seat belt ribs in pulley grooves and ensure correct tracking
• Rotate the blower by hand to confirm alignment before reassembly and test run

The Dryer Leveling Foot is an OEM part for Whirlpool dryers. It is designed to support and stabilize the dryer by allowing adjustments to the height and leveling of the unit. Proper leveling ensures the dryer operates smoothly and efficiently, reducing vibrations and preventing unwanted movement during cycles.

Causes of a bad leveling foot can include wear and tear from regular use, damage from moving the dryer, or breakage due to heavy loads and stress. Over time, the threads on the leveling foot can wear out, or the foot itself can become cracked or deformed.

Symptoms of a bad leveling foot include:

• Dryer rocking or wobbling during operation
• Unusual noises or vibrations
• Difficulty in adjusting the dryer's height
• Visible damage or wear on the leveling foot

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.