By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
Need Help?
Call
Dryer won't start, advance through cycles, or shut off? A faulty timer is often the cause. This mechanical control selects and advances drying programs.
But the new part and installed it. It was super easy. Read more
Fridge not cooling or excessive frost buildup? A faulty defrost timer may be cycling incorrectly. Straightforward DIY replacement restores automatic defrost.
I replaced the defrost timer and the defrost heater and this fixed the problem. The freezer does not ice up the intake holes to the fridge anymore. Read more
If your range won't heat, the display is blank, or temperature is incorrect, this control board regulates baking, broiling, and timer functions. Moderate DIY.
I worked with Bud and he was most helpful. I was very happy with the service that was offered. I liked the quick shipment, good packing and only paying ONE time for shipping. I would recommend your company again and would ask to deal with Bud again. Thanks for you service. Read more
Dishwasher not responding or display has no lights? This control assembly manages cycle selection and status display. Replaces worn or damaged controls.
Replaced the control board. Excellent response and delivery on the part! Thanks again! Read more
Dishwasher won't start, stops mid-cycle, or shows error codes? This electronic control board manages all cycles and functions. Moderate DIY repair.
All of the repairs were incredibly easy, however the experience might be different for everyone. My skills and background experience make troubleshooting and repairing fairly easy for me. I began the journey by troubleshooting out some of the peripherals such as the float mechanism and door latch switch by using a multimeter to ohm them out. I then moved towards the thermostat and turbinator. I measured the resistance on the thermostat and it seemed to be fine. I then cleaned the turbinator... Read more
If your mixer won't start smoothly or speed settings aren't accurate, this speed control board regulates motor power. DIY-friendly replacement.
Fixed with your replacement Read more
Fix a washer that won't advance cycles, stops mid-cycle, or repeats steps. This timer controls fill, wash, rinse, drain, and spin sequences.
Was most pleased that you sent an authentic GE part as promised since another company, who advertised same, sent me a refurbished piece that was totally unusable. You also saved us a considerable amount of money. Since we are not knowledgeable about installing electrical pieces, we had the condo handyman do it. It was done quickly and efficiently and works just fine. Thank you for your good and honest service.------Phyllis Wolpow Read more
Electronic clock control for the oven/range. This board drives the display and manages bake/broil commands, restoring accurate timekeeping and dependable oven controls when the original control has failed.
Ordered oven control board. easy fix, less than 15 minutes. works great! Read more
Oven not heating or display not responding? This electronic control board manages temperature, timing, and keypad functions. Moderate DIY repair.
My 15 year old son and I examined the new parts and made a plan for how we were going to take the front off of the oven. Turns out it was fairly simple. We removed the knobs, the knob shrouds, two philip screws on the side of the head and about 6, 6mm hex sheet screws. Voila! It came apart. We carefully looked at how the old parts were assembled and simply reversed the assembly with the new parts. Since one of our parts was the entire front head, it went together quickly and it was a perfect... Read more
Washer stops mid-spin or shows F6E1 error? The motor control board regulates drive motor speed and direction. Most DIYers replace it in 15-30 minutes.
On-line chat with AppliancePartsPros told me the error code was was for motor speed and they sent me a .pdf file on what to do to T/S it. Following the sheet I checked motor and Tack resistance and wiring - all OK, so I ordered a Motor Controller Ckt board assy. It arrived in 24 hours, during that time i watched the replacement videos and removed the old part. Upon receiving the new part I installed it (15 min), tested the washer (it worked), then put all the panels back on, pushed the washer... Read more
Fix a dryer that won't turn off or advance through cycles with a new timer. Controls cycle duration and automatic shutoff. Moderate DIY repair.
Changed the thermostat Read more
Microwave not heating or showing F1 E5 error? This inverter board converts voltage to power the magnetron. Requires tech sheet for testing procedures.
Fix a washer with no lights or unresponsive controls by replacing the encoder control board. Moderate difficulty repair requiring panel removal.
Refrigerator not cooling or door alarm won't stop? The control board regulates cooling cycles. Moderate DIY difficulty—disconnect power and match wires.
Purchased a new Control Board, as well as a new Thermister. Thermister was not absolutely necessary and could have been tested but it was simple enough to just replace during the control board replacement. Since it was a good time to replace the carbon air filter, I included that in the order too. Ordering the parts was very easy and completing the order the same. Parts arrived within a couple of days, which is good to know if you are depending on an appliance working. Impressed that... Read more
This is a Whirlpool range control board. It manages and monitors temperatures for the range and features a digital display and user interface buttons. The control board can short out due to power surge or exposure to excessive heat. For example, if the oven's self clean function is run too long or too frequently, parts of the control board could melt or otherwise malfunction.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the control panel in place. Remove the screws from each side of the control panel to gain access to the old control board. Disconnect any wire harnesses connected to it and remove any screws mounting it in place before installing the new part.This is a genuine OEM part compatible with ranges manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.
After trouble shooting, ordered electronic board from appliance parts pros.com I received it the next day and installed it. works find. Read more
Distributes power to control and heating circuits. Replace when board is damaged, failed, or non-responsive. Installs at bottom of cooktop unit.
I repaired the problem by replacing the Power Board assembly and the daughter relay board. Not sure which one was the problem. Since I had it apart I replaced both. So far the unit is working like new. Everything was plug in, so I didn't have to worry about complex wiring. I took pictures prior to disassembly to make sure I got the reassembly right. Worth the effort to fix it- very satisfying. Read more
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.