Gasket & Seal

This horizontal oven door seal lines the top and bottom edges of the door opening to keep heat contained inside the cavity. Replacing a worn seal restores stable temperatures, more efficient preheating, and consistent baking results.

• Seals the oven opening along the top and bottom edges to reduce heat loss
• Helps maintain set temperature and overall cooking performance
• Replaces cracked, frayed, flattened, or brittle horizontal gasket
• Common signs include visible gaps, heat escaping around the door, longer preheat times, and temperature fluctuations

• Disconnect power and allow the oven to cool completely before servicing
• Open the door and carefully pull the old seal straight out of the retainer
• Note clip/retainer positions as you remove the old seal and reuse them as designed
• Press the new seal evenly into place without stretching; ensure corners are fully seated for a uniform seal

This freezer door gasket creates an airtight seal between the door and cabinet to keep cold air in and humidity out. A tight seal helps maintain proper temperatures and reduces frost buildup and energy loss.

• Seals the freezer door perimeter to prevent warm, moist air from entering
• Helps reduce frost/ice buildup and temperature swings
• Common failure signs: torn or warped gasket, gaps around the door, frost forming quickly, door not sealing unless pushed
• Restores proper door closure and sealing performance

• Unplug the appliance before service
• Soften the gasket in warm water or with a low-heat hair dryer to ease installation and improve fit
• Remove and reinstall retainer screws or press-in tabs as applicable; work evenly around the door
• Check door alignment and perform a dollar-bill test around the perimeter to confirm a uniform seal

This rear gasket cover helps seal and protect the rear edge of a refrigerator cover or panel, maintaining a proper barrier to keep cold air where it belongs and prevent moisture or debris intrusion.

• Seals the rear edge of the cover to reduce air leaks
• Helps maintain stable internal temperatures
• Can address issues like warm spots, excess frost, or condensation around the rear cover area
• Replaces a cracked, deformed, or missing rear gasket cover

• Unplug the refrigerator before servicing
• Remove any shelves, drawers, or panels blocking access to the rear cover
• Carefully release retaining tabs/screws, transfer the gasket cover, and seat evenly
• Verify the cover is fully engaged and sealing before restoring power

This oven door gasket forms a heat-resistant seal between the oven door and the front frame. Replacing a worn seal helps the oven reach and maintain set temperatures and keeps hot air and steam from leaking around the door.

• Seals the oven cavity perimeter to limit heat and steam escape
• Helps the oven preheat properly and hold a consistent temperature
• Can help with symptoms like heat leaking at the door, longer preheat times, and uneven baking
• Replace if the gasket is torn, flattened, brittle, or visibly frayed

• Disconnect power at the breaker; allow the oven to cool completely (shut off gas supply if applicable)
• Pull the old gasket straight out of the retainers/clips, noting orientation and clip locations
• Clean the mounting area; press the new gasket into the retainers without stretching, seating corners fully
• Close the door to check fit and adjust seating as needed, then run a short heat cycle to condition the seal

The Sealing is an OEM replacement part for Bosch brand dishwashers. Located on the perimeter of the small rinse aid compartment door, this resilient rubber piece forms an essential water-tight seal when the dispenser is closed.   

Symptoms of a potentially problematic rinse aid door sealing include:

• Leakage or spills within the rinse aid reservoir
• Mineral deposits or residue build up inside the compartment  
• Cracks, tears, or deformation of the sealing material

Causes of a faulty rinse aid door sealing can be repetitive opening/closing stress breaking down pliability long-term. Exposure to chemical vapors from the rinse aid may also degrade sealing properties.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

This thermistor seal is the grommet that seals the temperature sensor where it passes through the washing machine's outer tub. Replacing a worn seal restores a watertight fit and helps prevent leaks that can damage surrounding components. What it does

• Forms a watertight barrier around the tub temperature sensor (thermistor)
• Helps keep the sensor securely positioned in the mounting port
• Common failure symptoms: water leaking during cycles, puddles under the unit, visible cracking/hardening of the grommet, or a loose sensor fit

• 1 thermistor seal

• Disconnect power and water; drain any remaining water from the tub
• Access the thermistor on the outer tub, disconnect its harness, and remove the sensor
• Pull out the old seal, clean the opening, press in the new seal, and reinstall the sensor fully seated
• Run a brief test cycle and check for leaks before final reassembly

The Door Gasket Assembly is an OEM part for LG refrigerators. This part creates a tight seal around the refrigerator door, preventing warm air from entering and cool air from escaping. 

Common causes of a bad gasket include wear and tear over time, damage from frequent door opening and closing, or exposure to temperature fluctuations that cause the material to degrade. 

Symptoms of a bad door gasket assembly include:

• Visible cracks, tears, or deformities in the gasket
• The refrigerator door not closing properly
• Increased condensation or frost buildup inside the refrigerator
• Higher energy bills due to the refrigerator working harder to maintain temperature

This OEM LG part is also compatible with some Kenmore models.

This foam seal fits between mating parts to create a tight barrier that helps prevent leaks and rattling. Replacing a worn or missing seal restores proper sealing and helps keep your appliance running quietly. What it does:

• Creates a compliant gasket between components to limit air or moisture passage
• Helps dampen vibration and reduce rattling/buzzing where parts meet
• Helps maintain proper airflow or fluid routing as designed
• Typical symptoms include leaks, condensation/frost near a joint, or new vibration noises

• One foam seal

• Disconnect power; turn off the water supply before service
• Note the original seal's routing/orientation before removal
• Clean and dry all mating surfaces; remove old foam and residue
• Install without stretching or over-compressing; ensure even contact with no gaps

This freezer door gasket replaces the perimeter seal on the freezer door. It restores a tight closure that keeps cold air in and moisture out, helping maintain proper temperature and reduce frost and condensation around the door. What it does:

• Seals the gap between the freezer door and cabinet to contain cold air and block humid room air
• Replaces a cracked, torn, shrunken, or warped gasket that no longer seals properly
• Helps address frost or ice near the door opening, moisture on the gasket, rising freezer temps, or a door that won't stay fully closed
• Supports consistent cooling and reduces air leaks that can lead to longer run times

• One freezer door gasket

• Unplug the refrigerator before servicing
• Warm the new gasket with hot water or low heat to relax shipping folds; do not overheat
• Remove the old gasket and clean the sealing surfaces; seat the new gasket fully in the door channel, starting at the corners
• Close the door and check for uniform contact (paper/dollar-bill test); allow the gasket to conform over 24 hours

This replacement door gasket creates a tight seal between the refrigerator door and cabinet. It restores proper sealing to keep cold air in and moisture out when the original gasket is torn, warped, or leaking. What it does:

• Forms an airtight barrier around the door opening to prevent air leaks
• Helps maintain consistent temperatures and reduce frost or condensation
• Replaces gaskets that are cracked, brittle, misshapen, or not sealing
• Common fix for doors that won't close or seal properly

• 1 door gasket

• Unplug the refrigerator before servicing
• Warm the new gasket in hot water or with low heat to relax folds
• Start at the corners and press the gasket lip into the channel; tighten any retainers evenly
• Close the door and check for even contact all around; adjust hinges if necessary

This refrigerator door gasket seals the fresh food compartment door to keep cold air in and humid air out, helping maintain stable temperatures and efficiency. Replace a cracked, warped, or loose gasket to restore a reliable door seal.

• Forms an airtight seal around the fresh food door to prevent warm air intrusion
• Helps maintain proper temperature and reduce moisture/condensation near the door opening
• Common failure signs: tears, gaps, warping, brittleness, door not closing flush, persistent condensation
• Air leaks can lead to longer run times or warm spots in the refrigerator

• Disconnect power before servicing
• Soften the new gasket in warm water or with gentle heat to relax folds; do not overheat
• Clean the door surface and gasket channel; transfer any retainers/screws if your model uses them
• After installation, check the seal all around (dollar-bill test) and adjust door/hinges if needed

The Dishwasher Seal Duct Nozzle is essential for maintaining the optimal performance of your dishwasher. This genuine OEM part ensures a secure seal within your Samsung dishwasher, preventing leaks and enhancing overall efficiency. Designed specifically for Samsung dishwashers, the Seal Duct Nozzle helps regulate water flow and pressure, ensuring that your dishes are cleaned thoroughly and effectively. Its durable construction guarantees long-lasting performance, reducing the need for frequent replacements. Installing the Dishwasher Seal Duct Nozzle is straightforward, allowing you to restore your applianceGÇÖs functionality quickly and easily. By choosing this genuine OEM part, you ensure compatibility and reliability, keeping your dishwasher running smoothly and extending its lifespan. Trust the Dishwasher Seal Duct Nozzle to provide the quality and performance you need for a spotless and efficient kitchen experience.

This refrigerator door gasket creates a tight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn or torn gasket restores consistent cooling performance and helps prevent frost and condensation from air leaks.

• Forms an airtight seal around the door perimeter to contain cold air
• Helps maintain proper temperatures and humidity inside the refrigerator
• Reduces frost, condensation, and warm spots caused by leaking seals
• Typical signs of failure: tears, gaps, hardened/warped corners, or doors not sealing firmly

• Unplug the appliance before servicing
• Let the new gasket warm to room temperature; use warm water or a hair dryer on low to relax bends
• Press the gasket fully into the door channel and seat the corners evenly
• Close the door and check for uniform contact all around; allow time for the gasket to conform

This oven door gasket seals the perimeter of the door to keep heat inside the cavity. Replacing a worn seal helps maintain consistent temperatures and proper preheat, improving baking performance and preventing heat from leaking around the door.

• Creates a heat-resistant seal between the oven door and front frame
• Helps maintain set temperature and stable preheat times
• Reduces heat loss and air leaks around the door
• Common symptoms: visible tears or fraying, flattened/hardened gasket, gaps around the door, longer preheat or cook times

• Disconnect power or gas and allow the oven to cool completely before starting.
• Open the door and carefully remove the old gasket; note the orientation of ends/clips for reinstallation.
• Clean the gasket channel/retainer of debris for a proper fit.
• Install without stretching; seat corners fully and ensure the ends meet snugly for a continuous seal.

This refrigerator door gasket forms an airtight seal between the door and cabinet to keep cold air in and humid air out. Replacing a worn gasket helps stabilize temperatures, reduce frost and condensation, and improve overall cooling performance.

• Seals the door perimeter to prevent air leaks
• Helps maintain set temperatures and humidity levels
• Reduces frost buildup and condensation around the door
• Common symptoms include rips/tears, warping, gaps, poor door seal, or visible moisture/frost at the door

• Disconnect power; let the interior warm slightly to soften the old gasket (or warm the new gasket in hot water)
• Pull the old gasket from the retainer/groove and clean mating surfaces
• Press the new gasket fully into the retainer, seating the corners first and working evenly around the door
• Use warm water or low heat to relax wrinkles; adjust door/hinges if needed