Parts for Lg DLEY1901WE: Other Parts

The Heater Assembly is an OEM replacement part for LG dryers. It is a critical component responsible for generating the heat necessary for drying clothes efficiently and effectively.

Symptoms of a bad heater assembly:

• Dryer not producing enough heat or failing to dry clothes completely
• Excessive drying times or inconsistent drying performance
• Visible damage or breaks in the heating element coil
• Burning odors or smoke emanating from the dryer during operation

Causes of a bad dryer heater assembly can include mechanical failure, electrical malfunctions, or simply reaching the end of its lifespan due to repeated heating and cooling cycles.

This OEM LG part is also compatible with Sears/Kenmore dryer models.

The Dryer Drum Baffle is an OEM part for LG dryers. This baffle is attached to the inside of the dryer drum and is designed to help lift and tumble clothes during the drying cycle. 

Causes of a bad dryer drum baffle can include wear and tear from regular use, physical damage from heavy or sharp objects, or becoming loose due to vibration over time. 

Symptoms of a bad dryer drum baffle include:

• Thumping or banging noises during the drying cycle
• Clothes not tumbling properly, leading to uneven drying
• Loose or rattling baffle inside the drum
• Visible damage or breakage on the baffle

This OEM LG part is also compatible with some Kenmore models.

This main control board is the appliance's primary power and logic module, replacing a failed control assembly to restore normal operation and control. Use when the unit loses power, won't respond, or shows control/display errors. What it does:

• Regulates power distribution and control signals to the appliance's motors, valves, and user interface
• Handles user inputs and runs appliance cycles via onboard logic
• Common symptom: appliance won't start or intermittently loses power/control
• Common symptom: touchpad/buttons, lights, or display are unresponsive or show error codes
• Common symptom: unit cycles on/off or behaves unpredictably due to faulty control logic

• One main control board

• Disconnect power to the appliance before accessing the control board
• Handle the board by its edges and avoid static discharge; use ESD protection if available
• Panel removal and wiring unplugging are typically required; note connector locations before disconnecting

The Belt is an OEM replacement part for LG dryers that is responsible for connecting the motor to the drum to allow it to tumble. Over time, dryer belts can stretch, wear out, or even break, leading to a drum that won't turn and clothes that don't dry properly.

Symptoms of a bad Dryer Belt include:

• The dryer motor running but the drum not turning.
• A squealing or thumping noise coming from the dryer.
• The dryer not starting at all.

Causes of failure can include regular wear and tear from the dryer's operation, overloading the dryer beyond its capacity, which puts extra strain on the belt, or a misalignment that causes uneven wear. A damaged belt can prevent your dryer from functioning correctly, leading to inefficiency in drying clothes and potential motor damage due to unnecessary strain.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Hi Limit Thermal Fuse is an OEM part for LG dryers. This fuse is a safety device that protects the dryer from overheating by cutting off power to the heating element if the dryer’s temperature exceeds a safe limit. It ensures that the dryer operates within safe temperature ranges, preventing potential fire hazards.

Replace the hi limit thermal fuse if it becomes faulty due to wear and tear, a buildup of lint, or exposure to high temperatures over time. A malfunctioning fuse can compromise the dryer’s ability to regulate heat properly.

Symptoms of a bad hi limit thermal fuse include:

• The dryer not heating
• The dryer shutting off unexpectedly during a cycle
• No response from the dryer when attempting to start a cycle
• Extended drying times due to lack of heat

This OEM LG part is also compatible with Sears/Kenmore models.

The Drum Seal is an OEM part for LG dryers. This part ensures a tight seal between the dryer drum and the dryer body, preventing hot air from escaping and maintaining the efficiency of the drying process. A well-functioning drum seal is important for the best dryer performance, contributing to energy efficiency and the prevention of unnecessary wear on clothing during the drying cycle.

Causes of a bad drum seal can range from natural wear and tear over time to overloading the dryer, which can strain and stretch the seal, leading to a poor fit.  

Symptoms of a bad Drum Seal include:

• Clothes taking longer to dry
• Increased energy usage due to loss of heat
• Excessive lint and debris outside of the lint filter area
• A noticeable gap between the dryer drum and the dryer body

This OEM LG part is also compatible with some Kenmore models.

The Hi Limit Thermostat Assembly is an OEM part for LG dryers. This thermostat monitors and regulates the temperature within the dryer to prevent overheating, ensuring safe and efficient operation. It acts as a safety device that shuts off the heating element if the dryer exceeds a certain temperature, protecting the appliance and your home from potential fire hazards.

Over time, the hi limit thermostat can fail due to wear and tear, electrical issues, or repeated exposure to high temperatures. If the thermostat becomes faulty, it can lead to improper temperature regulation within the dryer.

Symptoms of a bad hi limit thermostat include:

• The dryer overheating
• The dryer not heating at all
• The dryer shutting off mid-cycle
• Extended drying times due to inconsistent heating

This OEM LG part is also compatible with Sears/Kenmore models.

The LAMP, LED is an OEM component specifically designed for LG dryers. It provides illumination inside the dryer drum, a crucial safety feature for easily viewing clothes during operation. Proper lighting allows users to monitor drying progress without hindering efficiency.

Causes of a bad LED lamp can include regular wear and tear over extended use, as well as potential electrical issues disrupting current flow to the lighting source.

Symptoms of a bad LED lamp include:

• Dim or completely absent lighting inside the dryer drum
• Inability to visually inspect clothes without opening the dryer door
• Premature ending of cycles due to detection of insufficient light  

The high-efficiency LED technology in this OEM part helps maximize useful life. Replace yours today to restore optimal usability. This LG replacement part is also compatible with Sears/Kenmore models.

This connector nozzle is the small channeling fitting that routes fluid or air where needed in the appliance, restoring correct flow and reducing leaks or poor dispensing when the original is damaged. It's a direct-fit service part designed for straightforward replacement. What it does

• Directs fluid/air through the appliance plumbing or dispenser pathway to ensure proper flow.
• Replaces cracked, broken, or worn nozzle connectors that can cause leaks or reduced dispensing performance.
• Helps restore normal operation when the nozzle is visibly damaged, loose, or obstructed.
• Works as the mating piece between tubing and the appliance's internal assembly to maintain a sealed connection.

• One connector nozzle

• Disconnect power and shut off water supply before servicing.
• Inspect adjoining seals, gaskets, and tubing; replace any damaged components.
• Seat the nozzle fully and secure per OEM torque/fastening guidance to avoid leaks; do not overtighten.

The Roller Kit is an OEM part for LG dryers. This 4 roller kit includes replacement drum support rollers, which are essential for allowing the dryer drum to rotate smoothly during operation. The rollers are designed to provide stable support for the drum, minimizing noise and ensuring efficient drying performance. 

Over time, drum rollers can wear out due to continuous use, exposure to heavy loads, or lack of proper lubrication. When the rollers become damaged or worn, they may develop flat spots, lose their smooth surface, or begin to squeak. These issues can lead to improper drum rotation or increased strain on other dryer components.

Symptoms of a bad Roller Kit include:  

• Loud squeaking, rumbling, or thumping noises during operation  
• The dryer drum not spinning or rotating unevenly  
• Excessive vibrations while the dryer is running  

This OEM LG part is also compatible with Sears/Kenmore.

This is an authentic OEM drum support roller sourced directly from the manufacturer for use in clothes dryers. During the drying cycle, the drum turns and tosses the clothes around to distribute heat. This drum support roller holds the drum in place as it rotates. Over time, the heat from the dryer can lead to the roller becoming worn. If the dryer is making squealing sounds or thumping when operating, the support roller is worn out and should be replaced. Before replacing the drum support roller, make sure the power is disconnected from the dryer. Remove the top and front panel of the dryer to reach the drum. The idler pulley and dryer belt are underneath the drum; remove these and then take the drum out of the unit and set it aside. Remove the mounting bracket holding the worn drum support roller. Remove and replace the worn roller. While the dryer is apart, inspect the remaining support rollers. Reverse the steps used and put the dryer back together. Power the dryer and make sure the drum turns.This is a black and white, rubber and metal part that is individually sold. It does not come with assembly hardware. This drum support roller is designed for dryers manufactured by LG, Kenmore, and General Electric.

The Hinge is an OEM part for LG dryers, designed to enable smooth door operation. This critical component ensures proper alignment and efficient sealing to prevent heat loss and noise. Continuous use may cause wear, affecting alignment, sealing, and dryer safety and efficiency.

Causes of a bad hinge can include physical wear from regular use, leading to loosening or deformation, corrosion or rust weakening the hinge and affecting its movement, and accidental damage like bending due to impact, impairing the door's ability to close properly.

Symptoms of a bad Hinge include:

• The dryer door hangs unevenly or won't close tightly.
• Increased difficulty in opening or closing the door.
• Squeaking, grinding, or other noises when the door is moved.
• Visible wear or damage, such as bending or breaking.

This OEM LG part is also compatible with some Kenmore models.

Restore smooth, aligned door movement with this refrigerator door hinge assembly. A worn or bent hinge can cause sagging and poor sealing; replacing it helps the door close properly so your fridge maintains consistent performance. What it does:

• Allows the door to pivot smoothly on the cabinet
• Helps keep the door aligned for proper gasket contact and sealing
• Replaces worn or bent hinge components to restore correct door operation
• Typical symptoms: door sagging or rubbing, difficulty closing, uneven gasket contact, squeaks/clicks when opening or closing

• One hinge assembly

• Unplug the refrigerator; shut off water supply to the unit
• Support the door and use a second person to prevent dropping or misalignment
• Note/mark hinge positions and transfer any spacers or caps from the original hinge as needed
• After installation, verify even gasket contact and adjust leveling before tightening fasteners fully

The Lint Filter is an OEM part for LG dryers. It serves a critical function in trapping lint and debris from clothes during the drying process. Located in the door or top of the dryer, depending on the model, this filter ensures efficient airflow and heat distribution by preventing lint from clogging the dryer vent. 

These issues typically arise from normal wear and tear or from not regularly cleaning the filter, which can cause it to become brittle or damaged over time.  

Symptoms of a bad Lint Filter include:

• Reduced drying efficiency, leading to longer drying times
• Excessive lint or debris escaping into the dryer vent, which can pose a fire risk
• Visible wear or damage to the filter, such as tears or holes, which can allow lint to pass through

This OEM LG part can also be used on Kenmore/Sears appliances. 

This locker assembly secures the washer door and completes the latch housing so cycles can run safely. Replacing a worn or damaged locker helps restore proper door closure and reliable start/stop operation. What it does:

• Secures and aligns the washer door/boot so the machine can operate without the door opening during a cycle.
• Engages the door latching mechanism so the washer can detect a closed door and start.
• Replaces a damaged or cracked lock housing that can prevent the door from staying closed.
• Common symptoms this part can address: washer won't start, door won't latch or stays open, or the door pops open during a cycle.

• Disconnect power (and water, if applicable) before starting any repair to avoid shock or injury.
• Basic hand tools are typically required; follow the OEM service manual for panel and door removal.
• Handle door glass and trim carefully to avoid damage; transfer any mounting brackets or strike plates only if needed.
• After installation, restore power and run a short test cycle to verify the door latches and the washer starts normally.

Note: Does not include moisture sensor bars. For the moisture sensor bars, order 2 of part# 6500EL3001A.

The Guide Cover is an OEM part for LG dryers. The part allows dust and debris to exit the dryer drum while preventing small clothing items from slipping through.

Causes of a bad Guide Cover can include accumulation of lint and debris that can restrict airflow, physical damage from handling or excessive use, and general wear that can compromise the fit and effectiveness of the cover.

Symptoms of a bad Guide Cover include:

• Increased drying times due to poor airflow.
• Unusual noises from lint hitting the fan or other components.
• Overheating of the dryer.
• Visible damage or misalignment of the cover that affects performance.

This OEM LG part is also compatible with Sears/Kenmore.

This precision fastener is designed for specific locations on the appliance. Replacing a missing or damaged screw restores secure mounting and reduces vibration or rattling, helping panels and components stay properly aligned.

• Secures brackets, panels, and internal assemblies where this screw is specified
• Replaces stripped, rusted, or lost hardware
• Helps eliminate looseness, vibration, and noise
• Maintains proper fit and alignment of parts

• Disconnect power and shut off water/gas before servicing
• Use the correct driver; keep removed hardware organized for reassembly
• Do not overtighten; install into clean, undamaged threads
• Confirm location and quantity using your model's parts diagram

This safety interlock assembly secures the washer door and signals the control when it's safe to run a cycle. Replacing a faulty unit helps restore proper locking and start functions to prevent interruptions and error codes.

• Locks the washer door and confirms it is closed to allow the cycle to start
• Sends door-closed/locked status to the control throughout the cycle
• Helps prevent the door from opening during spin or when water is present
• Common symptoms: won't start, won't lock/unlock, door error (dE) messages, cycle stops mid-wash

• Disconnect power before servicing; wear cut-resistant gloves
• Access the lock at the door opening; remove the mounting screws and disconnect the harness
• Transfer connectors to the new assembly, align, and secure without overtightening
• Ensure the door strike aligns smoothly with the new lock before testing

The Filter Guide is an OEM part for LG dryers. It plays a pivotal role in guiding and securing the lint filter in place within the dryer. This ensures that lint and other debris are effectively captured during the drying cycle, preventing them from clogging the vent or damaging internal components. 

Causes for replacement include physical damage, such as cracks or warping, which can occur from frequent use or accidental mishandling. A malfunctioning filter guide can compromise the dryer's ability to trap lint, potentially leading to overheating, decreased efficiency, or even a fire hazard.

Symptoms of a bad filter guide include:

• Difficulty in inserting or removing the lint filter
• Excessive lint accumulation outside the filter area
• The dryer taking longer to dry clothes or not drying effectively
• Unusual noises or vibrations indicating that debris is bypassing the filter

This OEM LG part is also compatible with some Kenmore models.

The Filter Guide is an OEM part for LG dryers. It plays a pivotal role in guiding and securing the lint filter in place within the dryer. This ensures that lint and other debris are effectively captured during the drying cycle, preventing them from clogging the vent or damaging internal components. 

Causes for replacement include physical damage, such as cracks or warping, which can occur from frequent use or accidental mishandling. A malfunctioning filter guide can compromise the dryer's ability to trap lint, potentially leading to overheating, decreased efficiency, or even a fire hazard.

Symptoms of a bad filter guide include:

• Difficulty in inserting or removing the lint filter
• Excessive lint accumulation outside the filter area
• The dryer taking longer to dry clothes or not drying effectively
• Unusual noises or vibrations indicating that debris is bypassing the filter

This OEM LG part is also compatible with some Kenmore models.

This factory fastener is the customized screw used to secure components on compatible LG appliances. It replaces missing or damaged screws to keep brackets, panels, and covers tight so parts stay aligned and rattle-free.

• Secures brackets, panels, trim, or covers at their mounting points
• Helps maintain alignment and reduce looseness, gaps, squeaks, and rattling
• Replaces stripped, rusted, or missing screws caused by vibration or wear
• Restores proper hold so components stay in place during normal use

• Disconnect power; shut off water to the appliance if applicable
• Use the correct driver bit and apply straight, firm pressure to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

The Moisture Sensor Holder is an OEM part for LG dryers. It is designed to securely house the moisture sensor, which detects the moisture level in clothes during drying cycles to adjust drying time and ensure efficient operation.

Causes of a bad moisture sensor holder can include wear and tear from regular use, damage from physical impact, or warping due to exposure to high temperatures.

Symptoms of a bad moisture sensor holder include:

• Inaccurate drying times
• Clothes remaining damp after a cycle
• Dryer running longer than necessary
• Sensor falling out of place

This OEM LG part is also compatible with some Kenmore models.

This moisture sensor connector assembly links the dryer's sensor bars to the control to monitor fabric dryness and adjust cycle time. Replacing a damaged or loose harness restores consistent Auto Dry operation.

• Connects the moisture sensor bars to the main control for Auto Dry feedback
• Transmits the low-voltage signal used to determine when clothes are dry
• Failure may cause Auto Dry to end too soon, run too long, or deliver inconsistent results
• Typical issues include broken wires, loose/corroded terminals, or a heat-damaged plug

• Disconnect power; if gas, shut off gas supply before service
• Access the moisture sensor area at the front/lint housing
• Match routing and clips, seat terminals fully on the sensor tabs, and secure the connector
• Keep wiring clear of sharp edges and moving parts; reassemble and test a Sensor Dry cycle

This damper assembly mounts at the microwave's exhaust outlet to direct airflow outside and block backdraft when the fan is off. Replacing a cracked or warped damper restores venting performance and helps reduce drafts and rattling noise.

• Opens with blower airflow and closes when off to help prevent outside air from entering through the duct
• Directs steam, smoke, and cooking odors to the exhaust path
• Helps reduce drafts/backdraft when the fan is not running
• Common failure signs: weak venting, flap stuck open/closed, or rattling/flapping noises

• Disconnect power at the breaker; if over-the-range, support the unit per manufacturer instructions
• Remove the vent grille/top cover to access the outlet and take out the old damper; reuse existing hardware as needed
• Match the new damper's orientation to the original so the flap opens with airflow and moves freely
• Beware sharp sheet-metal edges; wear cut-resistant gloves and test the fan after reassembly to confirm proper operation

This hinge bracket anchors the door hinge to the appliance cabinet, keeping the door aligned for smooth opening and a reliable seal. Replacing a bent or worn bracket restores proper door movement and reduces rubbing, sagging, and gaps.

• Secures the hinge to the cabinet/frame and supports door weight during operation
• Helps maintain door alignment for consistent gasket contact
• Restores smooth pivoting of the door
• Common signs it's needed: door sagging or rubbing, popping/creaking at the hinge area, loose mounting, or visible damage to the bracket

• Disconnect power; if applicable, shut off water
• Support the door while servicing; a second person is recommended
• Note hinge/bracket orientation and transfer any spacers/shims and hardware from the old bracket
• Tighten mounting screws evenly and verify door gaps and seal contact before restoring power

This hinge bracket secures the refrigerator door hinge to the cabinet, restoring stable door alignment and smooth opening. It replaces a worn or damaged mounting bracket so the door closes evenly and stays properly supported. What it does:

• Provides the structural mounting point for the door hinge to attach to the cabinet
• Restores proper door alignment and prevents sagging or uneven gaps
• Reduces binding and noisy operation caused by a bent or broken bracket
• Helps ensure the door seals correctly for consistent cooling performance

• One hinge bracket

• Designed for a direct replacement; use appropriate tools and support the door before removing hinge fasteners to avoid injury or damage
• Disconnect power and remove food from door edges if required by the manufacturer's service instructions
• Retain original screws or order as specified by the OEM

This is the rear tub drum for the washer's drum assembly; it supports the inner drum and helps keep loads balanced so the washer can tumble and spin properly. Use this part to restore stable drum rotation and reduce rubbing or banging noises. What it does:

• Supports the inner wash basket and maintains proper alignment during spin cycles
• Keeps the drum centered to prevent rubbing against the cabinet or seal
• Helps reduce loud banging, wobbling or excessive vibration during operation
• Works with the tub seals, bearings and suspension to maintain smooth rotation

• One rear tub drum

• Disconnect power and water before beginning any repair
• This is a major drum component; expect to remove the outer cabinet and other assemblies to access it
• Support the inner drum while separating components; bearings, seal and hardware may need inspection or transfer

This replacement locker hook mounts on the dryer door and engages the cabinet catch and door switch. It keeps the door securely closed so cycles can start and continue without interruption. What it does:

• Attaches to the door and latches into the cabinet catch to secure the door
• Actuates the door switch so the appliance recognizes the door is closed
• Replaces a cracked, bent, or worn hook
• Resolves issues like the door not latching, popping open, or the unit not starting

• 1 locker hook

• Disconnect power; if gas, also shut off the gas supply
• Open the door and remove the mounting screws securing the old hook
• Position the new hook and tighten screws, reusing existing hardware
• Check latch alignment; the door closes securely and the cycle starts

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly while staying aligned for a proper seal. Replacing a worn or bent hinge restores consistent door action and helps prevent latch and sealing issues.

• Provides the pivot point that allows the door to open and close
• Maintains door alignment so the latch and gasket engage correctly
• Helps prevent sagging, rubbing, and poor sealing
• Common symptoms: drooping or loose door, difficulty closing, binding/squeaking, visible damage

• Disconnect power before servicing; allow any hot surfaces to cool
• Support the door during removal/installation to prevent damage or injury
• Transfer any spacers, bushings, or screws from the old hinge
• After installation, verify door alignment and gasket contact; adjust per service information if needed

This door hinge supports and pivots the appliance door so it opens smoothly and closes securely, maintaining proper alignment and latch engagement. Replacing a worn hinge restores consistent door operation and helps prevent sagging, rubbing, and incomplete closure.

• Provides the pivot point and structural support for the door
• Helps keep the door aligned for proper latching and closure
• Common signs: door sagging, rubbing, or binding during operation
• Door won't close flush or pop open unexpectedly
• Visible hinge wear, looseness, or damage

• Disconnect power to the appliance before servicing
• Support the door to relieve hinge load before removing screws or pins
• Transfer any reusable spacers, bushings, or screws from the old hinge
• After installation, verify door alignment and latch engagement; adjust as needed

This hinge bracket secures the door hinge assembly to the cabinet, restoring proper door support and alignment for smooth opening and a tight seal. Use it when the hinge area is cracked, worn, or no longer holding the door square. What it does

• Supports and anchors the door hinge so the door stays aligned and closes properly
• Replaces a cracked, broken, or worn bracket that causes door sag or misalignment
• Helps stop rubbing, gaps, and uneven sealing caused by a loose or damaged hinge area
• Works as a direct-fit structural part for the hinge assembly on compatible LG units

• One hinge bracket

• Disconnect power to the appliance and empty the door before starting; have a helper support the door during removal/installation
• Use the correct screwdriver/socket size to remove and reinstall mounting fasteners; do not overtighten
• Inspect hinge pins, screws, and surrounding mounting points; replace any damaged hardware
• After installation, verify door alignment and seal; adjust hinge position if needed following OEM guidance

This door gasket forms a watertight seal between the appliance's tub opening and the door, keeping wash water contained during operation. Replacing a worn seal helps stop leaks and protects floors and nearby cabinetry. What it does:

• Creates a tight, water-resistant seal around the door opening
• Replaces a torn, cracked, flattened, or deformed gasket that can leak
• Common symptoms: drips from the door area, puddles at the front corners, visible damage or mildew on the seal
• Restores proper door compression and helps prevent moisture/steam from escaping

• 1 door gasket

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel and mating surfaces
• Seat the new gasket evenly; ensure it is fully pressed into its channel (some models use retaining bands or clips—transfer and reinstall as removed)
• Close the door to check for uniform contact, then run a short cycle to verify no leaks

This Cover Cap is a small trim piece that snaps into place to hide fasteners and finished edges for a clean, finished appearance. It restores the appliance's look and helps prevent dirt from collecting in exposed screw openings. What it does:

• Covers exposed screws and mounting holes for a neater appearance
• Helps keep dirt and debris out of openings around trim pieces
• Prevents accidental contact with fastener heads
• Useful when an original cap is cracked, missing, or faded

• Snap-in replacement; no special tools usually required
• Remove any broken fragments before installing the new cap
• Press firmly until the cap clicks into place; avoid forcing if it doesn't seat easily
• Disconnect power or follow safety steps before working near electrical components

This customized screw secures appliance panels and components for a reliable fit, helping maintain proper alignment and reduce vibration or rattling. Designed as a direct replacement to restore original fastening where the correct screw is required. What it does:

• Fastens panels, brackets, or components to prevent movement and vibration
• Restores secure mounting when a screw is missing, stripped, or damaged
• Helps stop rattling or intermittent contact caused by loose hardware
• Matches the OEM style for correct fit and function when replacing a lost or worn fastener

• Disconnect power to the appliance before performing any repairs
• Use the proper screwdriver or driver bit to avoid stripping the screw head
• Do not overtighten; snug until secure to avoid damaging threads or components
• Keep small parts away from children and pets during installation

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This cabinet hole cap plugs unused hinge or screw openings on the dryer cabinet. It restores a clean, finished look and helps keep lint and moisture out after a door reversal or service. What it does:

• Covers open hinge/screw holes on the dryer cabinet
• Helps block lint, dust, and moisture from entering through unused openings
• Restores a finished appearance; helps prevent snags around exposed holes
• Commonly replaced when a cap is missing, cracked, or loose

• 1 cabinet hole cap

• Disconnect power before working near the cabinet
• Remove any damaged cap and clean the opening
• Press the new cap into the hole until fully seated and flush
• Wear gloves; cabinet edges and holes can be sharp

The Blower Wheel is an OEM part for LG dryers. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes.

Causes of a bad blower wheel can include accumulation of lint and debris, wear and tear over time, or physical damage due to foreign objects entering the blower housing.  

Symptoms of a bad blower wheel include:

• Reduced or no airflow from the exhaust vent
• Unusual noises such as rattling or squealing during the drying cycle
• Clothes taking longer to dry or remaining damp
• Overheating or frequent shutdowns of the dryer

This OEM LG part is also compatible with some Kenmore models.

Adapt your gas dryer for propane with this LP conversion kit. It provides the correct orifice and regulator adjustments needed so the burner fires properly on LP fuel, helping ensure safe operation and consistent drying performance after a fuel change.

• Converts a compatible gas dryer from natural gas to liquid propane (LP)
• Helps ensure proper burner flame characteristics on LP
• Appropriate when moving to a home with propane or changing utilities
• Symptoms can include weak heat, improper flame, or sooting

• Disconnect power and shut off gas before servicing
• Installation and regulator/orifice adjustments must be performed per the service manual
• After installation, leak-check all connections and verify proper burner operation
• Do not attempt conversion without the correct kit for your specific model

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

This dryer duct assembly channels air from the drum to the blower and exhaust. Replacing a cracked or warped housing restores proper airflow, helps prevent lint bypass, and supports consistent drying performance.

• Directs and seals airflow between the drum and blower housing
• Helps maintain drying efficiency by minimizing leaks and lint bypass
• Damage or warping can lead to long dry times and reduced airflow
• Signs of failure include visible cracks, melted spots, or air/lint leakage around the duct area

• Disconnect power; for gas models, turn off the gas supply
• Access from the front by removing the top and front panel
• Note fastener locations and any attached brackets/harnesses, then transfer them to the new assembly
• Vacuum lint from internal ducting and verify seals before test run

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

The Dryer Thermistor is an OEM part for LG dryers, designed to monitor and help regulate the temperature within the dryer by providing feedback to the control board about the temperature inside the drum. This allows the dryer to adjust its heat settings accordingly, preventing overheating and ensuring clothes are dried evenly and safely.

Symptoms of a bad Dryer Thermistor include:

• Clothes not drying properly or taking longer than usual to dry.
• The dryer repeatedly stopping during a cycle.
• Error messages appearing on the dryer's display panel.
• The dryer getting too hot or not heating enough.

Causes of a bad Dryer Thermistor can include a buildup of lint and debris affecting its ability to accurately sense temperature, wear and tear over time, or electrical issues within the dryer's circuitry.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Dryer Blower Thermostat is an OEM replacement part for LG dryers. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle.

Causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.

Symptoms of a bad dryer blower thermostat include:  

• The dryer not heating up properly or taking longer to dry clothes
• The blower motor failing to turn on or running continuously
• Inconsistent or inadequate airflow during the drying cycle
• Error codes or fault indicators related to the thermostat or blower motor

This OEM LG part is also compatible with Sears/Kenmore models.

This metal mounting bracket secures internal components to the appliance frame, restoring proper alignment and reducing movement. Replace a worn or damaged bracket to stop rattling and maintain stable operation. What it does:

• Provides structural support to hold panels, controls, or assemblies in place
• Prevents excess vibration and noise caused by loose parts
• Keeps components aligned for reliable mechanical operation
• Helps maintain safe clearances between moving parts

• Turn off power and unplug the appliance before beginning work
• Use appropriate hand tools; retain any original fasteners unless replacements are specified
• Inspect adjacent parts and mounting points for damage; replace if worn

The Drum Motor Assembly is an OEM part for LG dryers. It serves as the powerhouse that drives the drum, enabling it to tumble clothes during the drying cycle. This essential component ensures your dryer operates smoothly, providing the necessary torque for consistent and efficient drying performance.

Causes of failure might include wear and tear from prolonged use, overload from trying to dry heavy loads, electrical issues like short circuits, or physical damage to the motor components. 

Symptoms of a bad Drum Motor Assembly include:

• The dryer drum fails to turn, even though the dryer powers on.
• Unusual noises, such as humming or buzzing, indicating the motor is struggling.
• The dryer stops unexpectedly during cycles or won't start at all.
• Decreased drying efficiency or clothes taking longer to dry due to inconsistent drum speed.

This OEM LG part is also compatible with Sears/Kenmore.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

The Idler Pulley Assembly is an OEM part for LG dryers. It plays a critical role in the dryer's drum belt tension system, helping to maintain proper tension on the belt so the drum can rotate smoothly during the drying cycle.

Causes of a bad idler pulley assembly can include wear and tear over time, buildup of lint or debris, or damage from an overloaded dryer. A malfunctioning idler pulley can lead to inefficient drying and potential damage to other dryer components.

Symptoms of a bad idler pulley assembly include:

• Squeaking or squealing noises during operation
• The drum not rotating properly or at all
• The dryer stopping mid-cycle
• The belt slipping or breaking

This OEM LG part is also compatible with Sears/Kenmore.

The Dryer Idler Pulley is an OEM replacement part for LG dryers. It is a critical component that helps guide and maintain proper tension on the dryer belt, ensuring efficient transfer of rotational force from the motor to the dryer drum.

Symptoms of a faulty dryer idler pulley include:

• Squeaking or grinding noises coming from the pulley area
• Visible wear, cracks, or damage to the pulley surface
• Slipping or irregular rotation of the dryer drum

Causes of a bad idler pulley can include normal wear and tear over time, exposure to high temperatures or lint buildup, misalignment or improper tracking, or physical damage from impact or foreign objects.

This OEM LG part is also compatible with Sears/Kenmore dryer models.

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

This self-tapping screw fastens panels, brackets, and internal components in compatible appliances. Replace a stripped, corroded, or missing screw to restore a secure fit and help prevent vibration, rattling, and misalignment.

• Forms/engages its own threads in sheet metal or plastic for a secure hold
• Secures covers, brackets, and assemblies to maintain alignment
• Helps reduce vibration and noise from loose components
• Replace if the head is stripped/broken, threads are worn, or the screw is missing

• Disconnect power and shut off water or gas, as applicable, before servicing
• Match to the original location and hardware; use identical length and thread where specified
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is damaged, repair it before installing the new screw

This drying rack sits inside the dryer drum to hold items stationary while warm air circulates around them. It lets you rack-dry shoes and delicates without tumbling, helping prevent banging and scuffing that can happen when items rotate. What it does:

• Provides a stable platform inside the drum for stationary drying
• Allows heated air to circulate around items while preventing tumbling
• Used for shoes, sweaters, hats, and other items approved for rack-dry cycles
• If missing or damaged (cracked frame, broken tabs, poor seating), you may hear rattling or be unable to rack-dry items

• 1 drying rack

• Disconnect power and allow the drum to cool before inserting or removing the rack
• Insert the rear of the rack into the drum supports, then rest the front edge on the door opening; ensure it is level and fully seated
• Load items evenly and do not overload; use the rack-dry or low-heat settings recommended in your owner's manual
• Remove the rack before resuming standard tumble cycles

The Water Valve is an OEM part for LG dryers. This valve controls the water supply to the dryer's steam setting which helps reduce wrinkles and refresh clothing.

Causes of failure can be mineral buildup overtime restricting flow, damage from freezing during winter months, or worn internal seals and mechanisms.

Symptoms of a bad water valve include:

• Inability to select or utilize the steam cycle
• Drips or leaks at the water inlet port
• Erratic water pressure during steam cycles
• Steam levels that fluctuate or cut off unexpectedly

This OEM LG part is also compatible with some Kenmore models.

This inlet hose routes household water into the appliance so it can fill and operate correctly. Replacing a damaged inlet hose restores proper water flow and prevents leaks that can cause poor performance or water damage. What it does:

• Channels incoming water from the household supply into the appliance
• Stops leaks and restores normal fill when the original hose is cracked, split, or worn
• Helps correct symptoms like no water entering the appliance, slow or intermittent fill, or visible leaking at the hose connection
• Works with the appliance's valve and fittings to maintain a sealed water path

• Turn off the water supply and unplug the appliance before starting any work
• Inspect fittings and seals; replace any worn gaskets to ensure a watertight connection
• Hand-tighten connections then check for leaks; avoid overtightening plastic fittings

This pipe connector joins appliance water tubing to the inlet assembly, restoring a secure, leak-resistant connection so the dispenser or ice-making system can get a steady water supply. Ideal when fittings are cracked or worn. What it does:

• Creates a watertight connection between supply tubing and the appliance inlet/valve
• Stops leaks caused by cracked, split, or loose fittings at the tubing junction
• Restores proper water flow to dispensers and ice makers when a bad connector is the cause
• Helps prevent water pooling and potential damage from slow leaks

• Turn off water supply and disconnect power before replacing the connector
• Inspect tubing ends for damage and trim squarely if needed before installing
• Use correct tools and tighten fittings per manufacturer guidance; do not overtighten
• After installation, restore water and power and check carefully for leaks

This inlet hose delivers water from the household supply to the appliance for normal fill cycles. It restores proper water flow when the original inlet hose is damaged, cracked, or leaking. What it does:

• Channels incoming water from the household supply to the appliance's fill valve
• Replaces a worn, cracked, or leaking inlet hose to stop external leaks
• Helps restore normal fill and wash cycles affected by restricted or damaged hoses
• Fits as a direct replacement for the corresponding OEM inlet connection

• One inlet hose

• Disconnect power and shut off the water supply before starting any work
• Inspect fittings and replace any damaged clamps or seals to ensure a watertight connection
• Hand-tighten connections, then snug with a wrench—avoid over-tightening which can damage fittings
• Test for leaks by running a short fill cycle and checking all connections

The Venting Kit is an OEM part for LG dryers. This part offers flexibility and efficiency in dryer installation and setup, this kit enables side or bottom venting of the appliance, facilitating optimal use of space in your laundry area. It's ideal for situations where the traditional rear venting is not feasible or preferred. 

Causes of venting system issues can include blockages, incorrect installation, or the use of incompatible parts, leading to reduced efficiency and potential safety hazards, such as overheating or fire risks.  

Symptoms of a bad or improperly installed venting system include:

• Extended drying times
• Excessive humidity or heat in the laundry area
• Unusual noises during operation
• Accumulation of lint in and around the dryer

This OEM LG part is also compatible with some Kenmore models.