Kenmore Washer Dryer Combo 110.088732791 (110088732791, 110 088732791) Parts

The Dryer Clip is an OEM component for Whirlpool electric and gas dryers. It securely fastens critical ductwork attached to the dryer cabinet. Over extended periods, the constant vibrations produced during tumbling cycles cause microscopic fractures or loosening within the clip material where it grips duct joints. 

Causes relate to ordinary fatigue from long-term resonance vibrations concentrated at anchoring points.

Symptoms involve:

• Loose or detached venting/ductwork affecting airflow
• Noticeable leaks emerging at separation interfaces
• Reduced drying effectiveness due to compromised ventilation

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Washer Capacitor is an OEM replacement part for Whirlpool washing machines. It is an essential electrical component that plays a crucial role in starting and running the washer motor efficiently.

Symptoms of a bad washer capacitor include:

• The washer not starting or failing to run
• Humming or buzzing noises from the motor during operation
• Error codes or indicators related to motor or electrical issues

Causes of a faulty capacitor can range from normal wear and tear over time to electrical surges, overheating, or physical damage.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

The Lid Switch Kit is an OEM part for Whirlpool washing machines. This part is responsible for detecting whether the washing machine lid is closed. If the switch senses the lid is open, it prevents the washer from starting or continuing a cycle, thereby protecting users from potential injury caused by the spinning agitator or drum. 

Causes of a bad Lid Switch Kit can range from physical damage, such as breaking or cracking due to heavy use or accidental impact, to electrical issues like wiring problems or failures in the switch mechanism itself. 

Symptoms of a bad Lid Switch Kit include:

• The washing machine not starting when the lid is closed. 
• The washer halting mid-cycle when the lid is not opened.
• No agitation or spinning action in the washer 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore mode

The Appliance Touchup Paint is an OEM product for Whirlpool appliances. This touchup paint is used to cover scratches, chips, and minor blemishes on the surface of various appliances, helping to maintain their appearance and protect them from rust and other damage. It is specifically formulated to match the original color and finish of Whirlpool appliances, ensuring a seamless repair.

Causes of needing touchup paint include everyday wear and tear, accidental impacts that cause chipping or scratching, and exposure to harsh cleaning chemicals that can damage the finish. Regular use of touchup paint can help keep appliances looking new and extend their lifespan.

Symptoms indicating the need for Appliance Touchup Paint include:

• Visible scratches or chips on the appliance surface
• Areas of exposed metal prone to rust
• Blemishes that affect the overall aesthetic of the appliance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Spin Tube Thrust Washer is an OEM component for Whirlpool washing machines. It is a washer that fits around the agitator shaft and helps create a seal between the agitator shaft and the aluminum tub. This washer allows the agitator to spin freely during the wash and spin cycles without causing excessive vibration or noise. 

Symptoms of a bad spin tube thrust washer include:

• Noises like banging or clunking coming from the agitator area
• Shaking or vibrating of the washer tub during spinning 

Causes of a bad thrust washer include normal wear and tear after extended use. Exposure to extended periods of unbalanced loads can also put excessive strain on the washer components and lead to premature failure of the thrust washer seal.

This replacement part is also compatible with select Kenmore, Maytag, KitchenAid, and Jenn-Air models.

The Spin Tube Bearing is an OEM replacement part for Whirlpool washing machines. It is a stationary bearing located inside the tub that supports the agitator and spin basket during operation. The bearing works to reduce friction and facilitate smooth spinning motion.

Symptoms of a bad spin tube bearing include:

• Excessive vibration or noise during the spin cycle
• The agitator or basket wobbling noticeably
• Difficulty Balancing loads
• Premature wear of other components

Causes of a bad bearing can include wear and tear due to repeated use over time, damage from cleaning products or foreign objects inside the tub, or improper handling during repairs.

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Push Clip is an OEM replacement part for Whirlpool dryers. Situated internally near the rear cylinder wall, it firmly secures the drum support roller assembly.

Causes of failure relate to fatigue from years of absorbing drum impacts and associated mechanical stresses. Corrosion penetration if moisture enters the clip mounting area increases operational resistance over time as well.

Symptoms consist of:

• Uneven drying and weakened tumbling action inside the cylinder
• Vibration or noise emerging from the rear roller area
• Premature wear signals stemming from dislocated roller assembly

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Retainer Clip is an OEM replacement part for Whirlpool direct drive washing machines.

Causes of a bad retainer clip can include wear and fatigue from continuous vibration over many wash cycles. Cracks or breaks in the plastic material may develop as well.

Symptoms of a bad Retainer Clip include:

• Water leaks detected around the pump area inside machine cabinet
• Loosening of hoses or tubes interrupting proper drainage flow
• Potential pump component detachment from disconnected lines
• Damage to neighboring components submerged by leaked water

The OEM Whirlpool part is also compatible with Maytag, Jenn-Air, and select Kenmore models.

The Agitator Kit is an OEM replacement part for Whirlpool top-loading washer models. Installed in the center of the wash basket, it aids in the mechanical agitation central to regular laundry cleaning.It contains the plastic cam and four plastic dogs needed to repair a malfunctioning or noisy agitator during the wash cycle.

Causes of a bad agitator kit can include wear and tear from regular use, overloading the washing machine, or damage from foreign objects getting caught in the agitator. Additionally, the components can degrade over time due to constant exposure to water and detergent.

Symptoms of a bad agitator kit include:

• The agitator not moving or spinning properly
• Loud noises or unusual vibrations during the wash cycle
• Ineffective cleaning performance
• The agitator becoming loose or wobbling

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dryer Belt (length 79-1/8 inches) is an OEM part for Whirlpool dryers. This belt wraps around the drum, the motor pulley, and the idler pulley to enable the drum to rotate during the drying cycle. It ensures that clothes are tumbled and dried evenly. Also available in repair kit AP3109603

Over time, the dryer belt can become worn or snap due to the constant tension and friction it endures. When the belt fails, the drum will no longer spin, and the dryer will be unable to dry clothes effectively.

Symptoms of a bad dryer belt include:

• The dryer drum not turning
• A burning smell from the dryer
• Unusual noises during operation
• The dryer running but not tumbling clothes

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Switch is an OEM part for Whirlpool dryers. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use.

You should replace the door switch if it becomes faulty. Causes of a bad door switch can include wear and tear from regular use, electrical failures, or physical damage from repeated opening and closing of the dryer door. A malfunctioning door switch can prevent the dryer from starting or cause it to stop mid-cycle.

Symptoms of a bad door switch include:

• The dryer not starting or responding when the door is closed
• The dryer stopping mid-cycle without reopening the door
• The dryer continuing to run when the door is opened
• Error codes related to the door switch or door lock mechanism

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Clip is an OEM part for Whirlpool dryers. This part secures the control knob to the dryer’s control panel, ensuring it remains firmly attached and functions correctly. The clip helps provide stability and precise control over the dryer settings.

Causes of a bad clip can include regular wear and tear, accidental damage during use, or stress from frequent adjustments.

Symptoms of a bad clip include:

• Knob becoming loose or falling off
• Difficulty turning the knob to adjust settings
• Knob not staying securely in place
• Knob wobbling or feeling unstable

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Cover Seal is an OEM part for Whirlpool washing machines. This seal ensures a tight fit between the washer's cover and the tub, preventing water from leaking during the wash cycle. It helps maintain the efficiency and cleanliness of the washing process by keeping water contained within the tub.

Common causes of a bad seal include wear and tear over time, exposure to harsh detergents, or physical damage from regular use.

Symptoms of a bad cover seal include:

• Water leaking from the washer
• Excess moisture around the washer
• Visible cracks or deformities in the seal
• Reduced washing efficiency

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Front Bearing and Seal Kit is an OEM replacement part for Whirlpool dryers. This kit includes the front bearing and seal for the dryer drum, which work together to provide smooth operation and prevent premature wear.

Causes of a bad front bearing and seal can include regular wear and tear from normal use, heavy loads that place extra strain on the bearings, or debris accumulation causing increased friction.

Symptoms of issues include:

• Noisy or grinding sounds coming from the drum area
• Vibration noticed during the operation
• Difficulty turning or rotating the dryer drum by hand
• Reduced efficiency and longer drying times

This OEM replacement kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.