Kenmore Washer 110.21292010 (11021292010, 110 21292010) Parts

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Capacitor is an OEM part for Whirlpool washing machines. This part stores and releases electrical energy to help start the washer's motor and maintain its operation during wash cycles. 

Causes of a bad capacitor can include electrical surges, overheating, or degradation over time.  

Symptoms of a bad Capacitor include:

• The washing machine not starting
• The motor humming but not running
• The washer stopping mid-cycle
• Unusual noises during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

These lid bumpers are sold individually.

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

This washer tub ring, sometimes called a tub cover, snaps onto the outer tub to contain splashing and guide water back into the basket. Replacing a cracked or loose ring helps reduce top-side leaks and protects fabrics at the tub opening. What it does:

• Forms the molded upper edge of the outer tub and acts as a splash guard
• Helps direct water back into the basket during wash and spin
• Maintains proper clearance at the tub rim to prevent fabric snags
• Common signs of failure: visible cracks/broken tabs, loose fit, or water splashing/leaking from under the lid/top

• 1 tub ring

• Disconnect power and turn off water; wear cut-resistant gloves
• Raise or open the top to access the tub opening
• Release the retaining clips/tabs and detach any connected hoses from the old ring
• Align and press the new ring evenly until all tabs fully engage; verify an even, secure fit before reassembly

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

This is the central agitator that fits over the drive shaft in a top-load washer to move clothing through the wash water. Replacing a worn agitator restores proper wash action, improving turnover and cleaning performance.

• Rotates and oscillates to circulate laundry, lifting and rolling items through detergent and water
• Common failure signs include poor or no agitation, clothes not moving, or longer-than-normal wash times
• Built with a durable poly/TPE body for consistent grip on fabrics and smooth operation

• Disconnect power and water; use proper PPE
• Remove the fabric softener cap and agitator bolt to lift the old agitator straight off
• Inspect splines and drive components; transfer or replace fasteners as required
• Seat the new agitator fully and tighten the bolt to manufacturer guidance; test for secure engagement

This mixing valve bracket secures the washer's water inlet valve to the cabinet, keeping the valve steady and properly aligned for hose connections. A correct-fit bracket helps reduce rattles and potential leaks caused by a loose valve.

• Mounts and supports the water inlet/mixing valve on the rear panel
• Maintains proper alignment for hot and cold supply connections
• Helps reduce vibration and rattling noises during fill
• Common signs it's needed: loose or dangling valve, misaligned hose connections, or leaks at the valve fittings

• Disconnect power and turn off both water supplies; relieve pressure before removing hoses
• Access the rear of the washer and remove fasteners securing the existing bracket/valve
• Transfer the valve to the new bracket, reusing the original hardware
• Reattach the bracket to the cabinet, reconnect hoses, restore power and water, then check for leaks

This rotary encoder mounts behind the washer's cycle knob and tells the main control which setting you select. When it fails, selections may be erratic or unresponsive. Replacing it restores accurate, dependable cycle selection. What it does

• Detects the position of the cycle selector knob
• Sends selection signals to the main control board
• Enables precise cycle and option changes
• Common symptoms: knob turns but lights don't follow, random/incorrect selection, can't select a cycle, won't start

• One rotary encoder

• Disconnect power to the washer before servicing
• Access the control console and remove the knob/dial to reach the encoder
• Note orientation, unplug the harness, release tabs/screws, and swap in the new encoder
• Handle electronics carefully and avoid static discharge; verify knob-to-light tracking before reassembly

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This spring retainer secures a tension spring within the mechanism so it stays aligned and under proper tension. Replacing a damaged retainer restores smooth, reliable movement and helps prevent the spring from detaching or wearing nearby parts. What it does:

• Anchors and guides the spring to maintain correct tension and alignment
• Helps prevent the spring from popping loose or chafing nearby components
• Can address issues like weak return action, uneven movement, or a mechanism that won't stay in position
• Direct replacement for a broken, cracked, or missing retainer

• 1 spring retainer

• Disconnect power; for water-bearing appliances, also turn off the water supply
• Carefully release spring tension; wear gloves and eye protection
• Note spring routing/orientation before removal for accurate reassembly
• Ensure the retainer is fully seated before restoring tension and testing operation

This dishwasher cam assembly is a precision-molded drive component that converts rotation into the timed movement the mechanism needs. Replacing a worn cam helps restore smooth, reliable actuation during the cycle and reduces sticking or misalignment.

• Converts rotational input into precise motion for the linked latch/actuator mechanism
• Maintains proper timing and engagement so the mechanism operates when commanded
• Wear or cracking can lead to slipping, binding, or incomplete travel
• Typical symptoms: associated action fails to engage/release at the right time, intermittent operation, or clicking/grinding noises from the mechanism

• Disconnect power at the breaker and shut off water before servicing
• Access the mechanism; note cam orientation and linkage positions
• Transfer any reusable pins/springs; install the new cam in the same orientation
• Run a test cycle to ensure proper operation and check for leaks or abnormal noises

This is the upper agitator (auger) assembly for top-load washers. It restores the one-way ratcheting action that pulls laundry downward during the wash stroke for proper rollover and cleaning performance. What it does:

• Drives the top half of a dual-action agitator to move clothes down in the tub
• Replaces a worn or stripped auger that lets the top agitator stop or slip
• Helps resolve weak agitation or poor clothes rollover
• Addresses clicking/grinding from worn internal ratchet components

• 1 agitator auger assembly

• Disconnect power before servicing
• Remove the fabric softener dispenser and agitator cap, then the agitator bolt
• Lift off the old auger, align splines, and seat the new auger on the lower agitator
• Reinstall the bolt and caps; run a short wash to confirm proper agitation

Includes water inlet valve, vacuum break, wire harness and connector hose.

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation