Kenmore Washer 110.28902790 (11028902790, 110 28902790) Parts

Size: 48 inches long. Clamp included. For 21 inch extension use 285702.

This water level pressure switch monitors the washer's tub water level through the air-pressure hose and signals the control when to stop filling. Replacing a faulty switch helps restore accurate fills and consistent cycle progress.

• Senses air pressure from the tub to determine water level
• Signals the control to start/stop filling and advance the cycle
• Common symptoms of a failed switch: fills too little or too much, stops filling early, won't advance into wash/spin, or shows water-level error codes
• Helps protect against overfill conditions when operating correctly

• Disconnect power and shut off water supplies before servicing
• Access through the control/console area; note hose and connector orientations
• Transfer the pressure hose and wire harness; ensure an airtight hose fit with no kinks or cracks, and clear any water/debris from the hose
• With the tub empty, run a quick fill test to ensure proper shutoff and cycle progression

The Capacitor is an OEM part for Whirlpool washers that starts the motor by storing electrical energy and releasing it when the washer begins its cycle. This part ensures the washer operates smoothly from the moment it starts, providing the necessary jolt to the motor that enables it to begin its various functions, including spinning and agitating. 

Causes of a bad capacitor can vary. Electrical surges can harm its internal components, while wear and tear over time may result in a reduced capacity to hold a charge.

Symptoms of a failing Capacitor include:

• The washer failing to start.
• A humming noise when the washer is supposed to begin its cycle 
• The washer starting but then quickly shutting down due to insufficient power to the motor.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This small clip secures the washer's agitator assembly. It holds components in place so the agitator engages the drive properly, helping restore steady agitation and preventing looseness or rattling during the wash cycle.

• Retains agitator components in their correct position for consistent wash action
• Helps prevent the agitator or upper auger from lifting off or wobbling
• Can address symptoms like weak/intermittent agitation, a loose agitator, or clicking from the center post
• Commonly replaced during agitator service to ensure a tight, reliable fit

• Disconnect power and turn off water before servicing
• Remove the dispenser and agitator cap; take out the center fastener/retainer as your model requires
• Lift the agitator to access the clip; note its orientation and use needle-nose pliers to remove and seat the new clip fully
• Reassemble, ensure the cap is secure, and test for proper agitation

Used to lock washer cabinet to rear wall of washer.

These lid bumpers are sold individually.

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.

Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.

Symptoms of a bad spacer include:

• Misalignment of components
• Unusual noises during operation
• Difficulty in assembling or disassembling parts
• Reduced efficiency of the appliance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Sold individually, four are needed to replace all parts. Screw part number WP3390631.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This rear panel support is the structural bracket that secures the appliance's rear cover/backguard in place. Replacing a worn or broken support restores proper alignment, helps protect internal components, and reduces vibration noise.

• Secures the rear panel/backguard to the chassis for stable, proper fit
• Maintains alignment of panels and mounting points
• Helps minimize vibration, flexing, and rattles from a loose rear panel
• Common signs of failure: cracked or missing bracket, stripped mounting points, panel movement or buzzing

• Disconnect power at the breaker; shut off gas supply
• Pull the appliance forward carefully to access the back; protect flooring
• Remove fasteners, replace the damaged support, and reuse original hardware/clips
• Keep wiring clear of sharp edges; tighten screws evenly without over-torquing and check for vibration before repositioning

This motor shield covers the drive motor on top-load washers to deflect splashes, lint, and debris away from the motor and wiring. Replace a cracked or missing shield to help protect the motor assembly at the base of the machine. What it does:

• Covers the washer's drive motor to deflect incidental water and debris
• Helps protect motor windings and terminals from splashes
• Replaces a cracked, warped, or missing cover
• Common signs: visible damage, rattling from the base, or corrosion/debris buildup around the motor

• 1 motor shield

• Unplug the appliance and turn off water supply before servicing
• Access the motor area from the bottom of the cabinet; note the shield's orientation
• Remove the damaged shield and install the new shield fully seated, reusing existing fasteners/clips
• Confirm clearance from moving parts before restoring power and testing

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.

Rubber grommet for motor mount stud.

Color: white. Measures about 5-1/2 inches in diameter, and 6 inches high.

Specs: 10-16 x 1/2 inch.

The Auger Agitator is an OEM part for Whirlpool washers. It is responsible for creating washing action by moving the clothing items back and forth in the drum.

A bad auger agitator can be caused by regular use, wear and tear, or damage from objects getting caught in the agitator. If you notice that your clothes are not being properly agitated or if the agitator is not spinning correctly, it may indicate a problem with the auger agitator.

Symptoms of a bad auger agitator include:

• Inadequate cleaning 
• Clothes getting tangled
• Unusual noises from the agitator 

Replace your faulty auger agitator with this genuine OEM part to restore your washer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.