Kenmore Dryer 110.71252011 (11071252011, 110 71252011) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90296
The Push Clip is an OEM replacement part for Whirlpool dryers. Situated internally near the rear cylinder wall, it firmly secures the drum support roller assembly.
Causes of failure relate to fatigue from years of absorbing drum impacts and associated mechanical stresses. Corrosion penetration if moisture enters the clip mounting area increases operational resistance over time as well.
Symptoms consist of:
- Uneven drying and weakened tumbling action inside the cylinder
- Vibration or noise emerging from the rear roller area
- Premature wear signals stemming from dislocated roller assembly
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Screaching noise Linda Z. • Kailua Kona , HI • February 06, 2015
Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP18776
The Top Lock is an OEM component for Whirlpool electric and gas dryers. It secures the outer metal cabinet door during drying cycles for safety and ventilation. This lock provides a method for releasing and latching the door tightly when shut.
Symptoms of a failing top lock may include:
- Inability to fully close or properly latch the dryer door
- Accidental opening from deficient locking during operation
- Difficulty manipulating the lock due to worn or broken parts
Causes related to normal wear of moving parts through frequent use over several years. Deformation from excessive exterior impacts could also damage locking mechanisms.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Clothes dryer drum stopped rotating Edward J. • Eclectic , AL • February 20, 2015
Located model number and went to Appliance Parts Pros.com to check the repair instructions on belt and motor. Used the suggestions to diagnose problem as a broken belt. I also ordered two top locks to replace the originals that were very brittle plastic that broke when I opened the dryer.
Ordered the parts on Presidents Day, and received the parts the next day. The dryer was back in service in 24 hours.
Read more
More
$12.51
- Compare At:
-
$14.76
- You Save:
-
$2.25
Genuine Whirlpool part
By: Whirlpool
Part Number: 279264
The Front Bearing and Seal Kit is an OEM replacement part for Whirlpool dryers. This kit includes the front bearing and seal for the dryer drum, which work together to provide smooth operation and prevent premature wear.
Causes of a bad front bearing and seal can include regular wear and tear from normal use, heavy loads that place extra strain on the bearings, or debris accumulation causing increased friction.
Symptoms of issues include:
- Noisy or grinding sounds coming from the drum area
- Vibration noticed during the operation
- Difficulty turning or rotating the dryer drum by hand
- Reduced efficiency and longer drying times
This OEM replacement kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Noisy & inefficient Richard M. • Indianapolis , IN • December 06, 2016
After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify...
Read more
More
$59.95
- Compare At:
-
$71.34
- You Save:
-
$11.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP488729
This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.
Do-It-Yourself Stories from Customers like You
The lint catch was broken Misti P. • Spokane , WA • January 18, 2019
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one.
Read more
More
$8.36
- Compare At:
-
$9.95
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP234826
The Natural Gas Orifice is an OEM replacement part for Whirlpool gas dryers. Installed within the dryer burner assembly, it regulates gas fuel flow into the burner.
Common causes relate to natural deposits obstructing the small gas port, as well wear inducing intermittent ignition of flames during many years of laundering cycles.
Symptoms of a failed orifice include:
- Slow or inefficient drying times and extended cycles
- Uneven or incomplete drying of loads
- Changes in flame appearance like higher than normal yellow tips
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Propane to natural gas conversion on range and dryer Vincent P. • Howell , NJ • October 09, 2014
Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time.
Read more
More
$25.95
- Compare At:
-
$30.88
- You Save:
-
$4.93
Genuine Whirlpool part
By: Whirlpool
Part Number: 279366
The Moisture Sensor is an OEM part for Whirlpool dryers. This part detects the moisture level in the clothing during the drying cycle, allowing the dryer to adjust the drying time accordingly.
Causes of a bad moisture sensor can include regular wear and tear, buildup of lint or residue, or physical damage.
Symptoms of a bad moisture sensor include:
- Clothes taking longer to dry or coming out still damp
- The dryer not stopping when clothes are dry
- The dryer shutting off prematurely
- Inconsistent drying results
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dampness sensor was broken George L. • Marquette , MI • March 24, 2014
Viewed the video before I purchased the part. Received the part and put it in. Everything went as planned.
Read more
More
$67.35
- Compare At:
-
$79.47
- You Save:
-
$12.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3399639
The Temperature Selector Switch is an OEM replacement part for Whirlpool dryers. This electro-mechanical switch allows consumers to choose between heat settings that adequately dry different fabric types.
Causes of a damaged selector switch can include regular wear from hundreds of cycles over the appliance's lifetime. Mineral deposits accumulating inside linkage mechanics may cause rotational movements to stiffen. The physical impacts of shifting internal contact positions could potentially lead to switching issues as well.
Symptoms of a faulty temperature selector involve:
- Inability to change heat level for desired drying performance
- Temperature remaining stuck on highest or lowest settings
- Lint filter or duct cleaning lights failing to illuminate properly
This OEM replacement is compatible with some Kenmore and KitchenAid electric dryer models too.
Do-It-Yourself Stories from Customers like You
1 no heat on high or low settings and sometimes on medium heat setting 2 no auto cool down Robert H. • Renton , WA • March 11, 2015
I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer.
Read more
More
$53.95
- Compare At:
-
$64.20
- You Save:
-
$10.25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
$7.95
- Compare At:
-
$9.46
- You Save:
-
$1.51
Genuine Whirlpool part
By: Whirlpool
Part Number: WP98234
This U-type nut clips over a sheet-metal edge to create a durable threaded anchor for a screw. It helps secure panels, trim, and brackets so fasteners hold tight and components stay aligned and rattle-free. What it does:
- Clips onto thin sheet metal to provide captive threads where a standard nut cannot be used
- Holds screws securely to fasten panels, trim pieces, or mounting brackets
- Addresses issues like loose panels, missing/broken clips, or screws that will not tighten
- Helps reduce vibration and rattling from unsecured components
What's included:
Install notes:
- Disconnect power and shut off gas/water before servicing
- Position the U-nut over the panel edge with the threaded side aligned to the hole
- Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
- Replace any damaged or corroded hardware to ensure a secure hold
Also known as: U-clip, speed nut, spring nut
Do-It-Yourself Stories from Customers like You
Broken dryer belt and not heating as good as it used to. Jimmie F. • Winfield , KS • January 15, 2018
I undid the top with a putty knife, took out two screws and took off the front. I replaced the drum rollers and put the new belt on the drum, looped the belt on the idler and then onto the motor pulley. I also put on two new top hold down clips as the old ones broke because they were plastic, the new ones were metal. I took off the back panel and replaced the heating element. The hardest part was cleaning up all of the lint and dirt that had accumulated over the years. It was not difficult,...
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8312709
The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment.
Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.
Symptoms of a bad clip include:
- Loose console assembly that is not securely fastened
- Misaligned or dangling controls that do not sit flush
- Dislodged console at risk of detaching from housing
- Missing clip leaving an open mounting point
This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
My kenmore washer model 11029828801 was agitating during the fill cycle and the tub would only partially fill also at the end of the spin cycle rinse water was spraying in resoaking the clothes Jay S. • Hammond , IN • February 07, 2017
I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new...
Read more
More
$18.95
- Compare At:
-
$22.36
- You Save:
-
$3.41
Genuine Whirlpool part
By: Whirlpool
Part Number: WP348197
This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:
- Maintains proper spacing and support between adjoining parts
- Helps prevent metal-to-metal contact, reducing scraping or grinding noises
- Addresses wobble or excess play when the original washer is worn, deformed, or missing
- Restores smoother movement and alignment in the assembly
What's included:
Install notes:
- Disconnect power and water supply before servicing; for gas combos, also shut off gas
- Refer to your model's parts diagram for location and orientation
- Track the order of any shims/spacers during disassembly and reinstall in the same sequence
- Tighten fasteners to manufacturer guidance to avoid deforming the washer or binding parts
Do-It-Yourself Stories from Customers like You
Screaching noise Linda Z. • Kailua Kona , HI • February 06, 2015
Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693140
This burner tube channels the gas-air mixture to the burner and includes an adjustable air shutter to set proper combustion. Replacing a damaged assembly helps restore reliable ignition, stable flame, and consistent heating performance.
- Directs the fuel/air mixture from the gas valve to the burner port
- Integrated adjustable shutter regulates primary air for proper flame
- Helps maintain efficient heat output and reliable burner operation
- Failure can present as no or intermittent heat, burner that lights then goes out, yellow/lazy flame, or soot
What's included: One burner tube with attached adjustable air shutter Install notes:
- Disconnect power and shut off the gas supply; allow the appliance to cool before servicing
- Access the burner compartment and transfer any clips/brackets from the original tube
- Note the current shutter position; after installation, adjust for a steady blue flame
- After reassembly, leak-test gas connections with a soap solution and verify burner operation
Do-It-Yourself Stories from Customers like You
Dryer not heating Ray M. • Marissa , IL • October 03, 2014
I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only...
Read more
More
$84.54
- Compare At:
-
$100.60
- You Save:
-
$16.06
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693995
This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.
- Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
- Helps maintain alignment and reduce rattling or vibration
- Replaces stripped, corroded, or missing screws of the same size
- Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware
What's included: One screw Installation notes:
- Disconnect power and shut off gas/water (as applicable) before service
- Match thread and length to the original; replace screws one at a time to keep parts aligned
- Start threads by hand to avoid cross-threading; tighten snugly without overtightening
- If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed
Do-It-Yourself Stories from Customers like You
There was no power cord and accessories to attach it Terry C. • Martin , TN • December 27, 2016
I put all pieces that I ordered on the dryer and plugged it in.
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3394509
This bearing ring is a small, low-friction spacer used in the dryer's drive system to let rotating components spin smoothly and quietly. Replacing a worn ring helps reduce drag, eliminate squeal, and protect related parts. What it does:
- Provides a bearing surface between a rotating wheel/pulley and its bracket
- Helps maintain smooth belt tracking and consistent tumble
- Reduces friction and wear on the belt and pulley/roller
- Common symptoms of wear: squealing/chirping while running, intermittent drum start, drag or burning-rubber smell
What's included:
Install notes:
- Disconnect power; for gas dryers, also shut off gas supply
- Access the drive system; release belt tension and remove the affected pulley/roller as required
- Note the order/orientation of spacers, washers, and clips; install the new ring in the same position
- Hand-rotate the assembly to ensure free movement before reassembly and testing
Do-It-Yourself Stories from Customers like You
Replace front drum bearing ring. Randy N. • Anoka , MN • January 18, 2020
New ring.
Read more
More
$52.33
- Compare At:
-
$62.27
- You Save:
-
$9.94
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07