Need Help?
Call
Seals the refrigerator door to prevent cold air loss and maintain efficiency. Replace if torn, cracked, or not sealing properly. Verify fit by model.
This door gasket presses into slot around door pull off old and press in new a five minute repair Read more
The Door Shelf is an OEM replacement part for Frigidaire refrigerators. This gallon door shelf measures about 23 inches wide from inside to inside.
Causes of a bad door shelf can include frequent use, overloading, or accidental impacts, leading to cracks, breaks, or warping. When the door shelf is damaged, it can compromise the stability and security of stored items, making it less effective for storage needs.
Symptoms of a bad part may include-
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more
Replacement drum support roller for dryers. Installs on the drum assembly to allow smooth rotation. Replace when cracked, worn, or making noise.
I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more
Idler pulley maintains belt tension in your dryer drum assembly. Replace if the wheel is cracked, bracket is broken, or pulley has worn bearings.
I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more
The Dryer Front Bearing Drum Slide (Green, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The green slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.
Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more
Replace your cracked, broken, or missing refrigerator door bin. This shelf installs on the door to hold bottles, jars, and condiments securely in place.
Upon receiving replacement rails snapped them in place and job was done. Couldn't have been any easier. Read more
Replace your freezer door gasket to restore an airtight seal and prevent frost buildup. Worn or torn gaskets let warm air in, causing ice formation and soft food. Confirm fit with your model number before ordering.
Frost & ice were building up inside the top of our upright freezer, so I replaced the door gasket. First I'll make my long story short, then I'll tell the longer story for those who might be interested and might benefit from my experience. Short version - The whole project took about three hours, but less than an hour of that would have been required if I were more of a handyman and if the freezer hadn't had prior work done on the door for the same frost buildup problem. Long version - When... Read more
This ice maker assembly produces and dispenses ice cubes in your refrigerator's freezer compartment. It automatically fills with water, freezes it into cubes, and releases them into the ice bin. Replace this part when your refrigerator stops making ice, produces misshapen cubes, or makes unusual noises during the ice-making cycle.
My first hour: I investigated first by pulling out refridgerator to see if the water line hose was kinked. I started under the kitchen sink where it begins, coming from faucet water supply. Then I followed it to the back of the fridge to see if anything looked odd. Next I went to the ice maker itself. I investigated the ice maker by removing the freezer food sliding tray and hanging tray, and then unscrewing the door off the slides. When I looked inside at the ice maker, I saw the tube where... Read more
Oven not heating or baking unevenly? This lower bake element restores proper oven temperature. DIY-friendly repair takes about 20 minutes to install.
Of course, these things always seem to happen on a holiday! Luckily we were not having guests for dinner - so quickly changed our eating plans for the evening. I went directly online and Googled "Bake elements for GE ovens". At first I did not think I would have luck finding this part because of the oven's age. AppliancePartsPros.com was one of the service dealers listed first and catered specifically to GE appliances and parts. So, I typed in the Model number and low and behold, a screen... Read more
The Drive Hub Kit is an OEM replacement part for Whirlpool washers. This kit includes an important transmission component - the drive hub - along with mounting hardware. The drive hub transfers power from the washer motor to turn the wash basket and agitate laundry.
Symptoms of a bad drive hub can include:
Causes of a bad drive hub include normal wear over time, strain from heavy or unbalanced loads, or damage from impact or other external forces.
This OEM replacement kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I watched a video on YouTube that showed my exact problem. It had a link to this part AP5665171 Hub and it showed how to fix it. It was a fairly simple fix. I did not even have to remove the tub. I popped the cap on top of the agitator plate (AGP), removed the bolt hold the AGP on. I tapped on the bolt several time to loosen it. Using an angled screw driver, carefully and slowly lifted up the edges of the AGP until I could use my fingers to carefully pull the AGP off the splined drive... Read more
Fix E1 error codes or overheating issues with this dryer thermistor. Monitors temperature to prevent shutdowns. DIY repair takes about 30 minutes.
I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more
Seals the gap between the dishwasher tub and door bottom to prevent water leaks. Replace if you notice leaking at the door base or visible wear.
The dishwasher is 4 years old, so I figured since it was leaking from the bottom, replacing the Tub Gasket PN: AP5690109, Splash Shield Kit PN: AP4338941 , and the bottom Door Seal/Gasket PN: AP5809675 was a good idea; the machine probably has around 1200 cycles in 4 years. There's no telling how much the door had opened and closed!? The bottom Door Seal/Gasket was badly worn, and the entire job took me around 30 minutes which included the detailed cleaning of the mating flanges. Take your... Read more
Replaces cracked, broken, or missing dishwasher rack stop clips. Secures upper or lower dishrack to track rail, preventing rack from sliding out too far.
My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more
Washer won't spin or leaves clothes soaking wet? A worn clutch assembly prevents the tub from spinning properly. Moderate DIY repair with video guide.
A couple of years ago, I had an issue with my Whirlpool washer which is every bit of 18 years old. I checked the internet for what might be wrong and stumbled across some how to videos on how to fix it. So, the other day, when my washer quit spinning the first thing I did is go to the internet again to see if I would be able to fix again. Thank you, Appliance Part pro.com, for your very helpful website with the very informative video's on how to replace parts! After I watched a... Read more
Ice maker stopped making ice? This complete ice maker assembly resolves no ice production and leaking issues. Easy DIY install with video guide included.
Well, I got online and found several YouTube videos on how to check what was happening. I have a multimeter and tools. I first replaced the external water filter just to make sure it wasn't that, and it needed it. That wasn't the problem. I then removed the water inlet valve which was really easy. I didn't disconnect the water lines but I did unplug the power plug. Using the ohms setting on the meter, I tested the coil of the valve solenoid. It wasn't open. I checked the voltage at the plug... Read more
Supports the front of your dryer drum for smooth, quiet rotation. Replace if you hear squeaking or grinding noises. Confirm fit with your model number.
I followed the directions I found on YouTube for removing the front of the dryer. It was fairly easy, with two screws to remove the top and another two to remove the front. Just use a hand Phillips screwdriver, you will have difficulty using a typical power screwdriver due to space limitations. Watch the tabs on the top that engage with the control panel. Push the top to the left to disengage. I broke one of the three. One connector and two fastons needed to be disconnected on the front. ... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.