Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Drives the drum rotation for even drying. Replace if dryer drum won't turn, makes squealing noises, or clothes stay wet. Confirm fit with your model.
I found a video on Youtube which described dryer drum squeaks as most likely caused by a worn rear drum bearing. I located the model number on the inside lip of the dryer door: Frigidaire Affinity LEQ6000ES2. I googled "frigidaire affinity dryer squeak". I got a link for my friends at AppliancePartsPros.com! I've used Appliance PartsPros 3 times before, so I figured I was in a "one-stop-solution" situation. I ordered a rear drum bearing kit as well as a dryer drum belt (after nearly 7 years... Read more
Replaces dim, flickering, or burnt-out bulbs in refrigerators, ovens, and microwaves. Restores interior lighting for visibility. Verify fit with model.
I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more
Supports and allows smooth drum rotation in your dryer. Replace if you hear squealing, grinding, or rattling noises during operation. Verify fit with your model.
Dryer won't start or shuts off unexpectedly? A failed thermal limiter is often the cause. This safety fuse prevents overheating. DIY repair in 30-45 minutes.
Recommendations have fun and a bucket to prevent losing parts. First watch the videos, practice disassemble and reassemble the dryer drum. Make certain you have a good screw driver and spatula from kitchen (could not find my putty knife). Secondly, clean and inspect everything, make sure the motor bearing and belt pulleys are in good condition with little or no play. Third after you have confidently disassembled, vacuum cleaned, inspected all the worn parts, grease the motor and pulley,... Read more
Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.
The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more
Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more
High-temperature adhesive secures gaskets, seals, and feet in hot zones. Replace when parts loosen or seals fail. Confirm fit with your model number.
I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more
Prevents lint, moisture, and heat from escaping around your dryer drum opening. Replace if torn or worn to restore efficiency. Verify fit by model number.
Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more
Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more
Supports the drum bearing in your dryer, allowing smooth drum rotation. Replace if cracked, broken, or worn to restore proper drum support and operation.
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros. Read more
Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.
Microwave won't turn on or has no power? A blown fuse is often the cause. This safety component protects against electrical surges and short circuits.
I have a Jenn-Air microwave that didn't turn on and had no lights. It just stopped working completely. I unplugged the unit and had to remove the rear cover using a *security screw kit* that prevents people from opening the rear panel. Once opened, I removed the fuse and testing it with an OHM reader to determine that the fuse went bad. But I also had to determine why the fuse blew and noticed a sticky oily substance under the Capacitor. I used a rubber glove and needle nose pliers to... Read more
Refrigerator warming up or frost building in freezer? The defrost thermostat monitors evaporator temperature. DIY-friendly repair in under 15 minutes.
Watched a few of your well put together videos and could not afford a new Refrigerator right now because it was a built in so decided with the frost on the bottom of the freezer grill and the Refrigerator warming up decided to replace the Heater Element and Thermostat Defrost which took some time but so far so good lets hope that is all that is needed saved over 10,000.00 dollars for a new 48" built in for now! Thank you for your rushed order and videos I think you are a life saver got the part... Read more
Flat-style dryer drum belt wraps around drum and motor pulley to spin clothes. Replace when belt breaks, frays, or drum won't turn. Confirm fit by model.
Replaced upper and lower felts. Painted rubbing surface on inside of drum with refrigerator enamel. Took out drum and lubed rear bearing. Replaced 2 of the 3 thermostats, and the belt just on principle. Spent a lot of time with shop-vac removing lint from drier and exhaust ducts. Runs great and is no longer cooking or staining clothes. Read more
Fixes loose panels, rattling doors, or wobbly components caused by stripped or missing screws. Secures brackets, covers, and mounting hardware. Easy DIY.
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find... Read more