Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more
Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure. This kit includes the catch and hardware. 10-minute DIY fix.
Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more
Dryer won't start or run? A blown thermal fuse is the likely cause. This safety component cuts power if temperatures get too high. Easy 15-min fix.
Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more
Captures lint and debris during drying cycles to maintain airflow and efficiency. Replace when cracked, torn, or damaged. Verify fit with your model.
I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more
Replacement timer knob for dryers. Installs on the control panel to set cycle durations. Order if your original knob is cracked, broken, or missing.
It's working now Read more
Fix dryer vibration or squealing with this drum roller shaft retaining ring. Secures rear wheels on axles. Small retaining ring pliers needed for removal.
Upon removal of the lower inspection panel on the front of the machine, my 20 year old son thought the motor was bad by the smell. But he did discover what turned out to be the belt tensioner pulley laying inside the machine. After he pronounced it dead, without a thought to the idler pulley, I looked at the machine and determined the lack of movement was due to the idler pulley having "fallen" off the shaft by looking at the illustrated parts break down provided on this website. Ordered the... Read more
Dryer drum roller axle mounts to the rear panel and supports drum rollers. Replace if bent, worn, or wobbling. Helps eliminate noise from damaged axles.
Replaced the tension pulley assembly, drum rollers, drum roller axles, belt, and drum glides while I had the dryer disassembled. It turned out that the cause of the squeak was the tension pulley assembly, however it was easy and economical enough to replace anything that could have been the cause of the squeaking while I had the dryer apart. The parts were ordered on Thursday afternoon and delivered on Friday. I had the dryer repaired and running like new in no time. For about $100, it was... Read more
Supports the drum bearing in your dryer, allowing smooth drum rotation. Replace if cracked, broken, or worn to restore proper drum support and operation.
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros. Read more
Captures lint and debris during drying to prevent vent clogs. Replace if damaged, warped, or worn. Confirm fit with your dryer model number.
Replaced Read more
Maintains tension on the idler arm to keep your dryer belt tight. Replace if the spring is stretched, broken, or missing to restore proper belt operation.
I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more
Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
White timer knob insert cap that fits over the timer control knob on your dryer's control panel. Replace if cracked, broken, worn, or missing.
Supports the dryer drum and allows smooth rotation. Replace if you hear grinding noises, see excessive wear, or notice drum wobbling. Confirm fit with your model.
Replaced them. Read more
Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.
Secures drum rollers, brackets, and panels in your dryer. Replace if stripped, corroded, or missing to restore safe, rattle-free operation. Confirm fit.
It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more
Factory fastener screw secures panels, brackets, and trim inside appliances. Replace missing, stripped, or damaged screws to restore tight fit.
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more