Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer leaking from inlet valve or not filling properly? This three-coil water inlet valve assembly controls cold water, bleach, and prewash. DIY fix in 15-30 minutes.
1. I unplugged the washer from outlet 2. I turned off the hot and cold water taps going to the washer (both just in case) 3. Draped a towel over back edge of washer and under where hoses coming from water outlets attach to back of washer (to catch any loose water out of the hose or screw nozzle leading to valve assembly, then unscrew (by hand) the cold water hose from back of washer (leave hot water hose alone as not needed). 4. Unscrew valve assembly from washer by two screws on back top of... Read more
Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.
Replaces worn or broken shock absorbers that stabilize the drum in your washer. Installs at the base of the tub to dampen vibrations during spin cycles.
After watching the video carefully and taking notes for step-by-step dismantling of the LG washer, I took it apart methodically placing each item on a table in the order removed. I was able to remove and replace the bearings with no problems following the tips and tricks. The spider did not seem to be in bad shape but since I had a new one, it seemed reasonable to replace it as well, but it was difficult to extract the old one from the drum. The bolts are assembled with weld glue, so it is a... Read more
Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.
Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm! Read more
Flexible drain hose connecting the pump to the tub. Replace if cracked, leaking, split, or missing. Installs between pump assembly and internal tub.
REMOVED BACK PANEL, USED PLYERS TO REMOVE CLAMP, PULLED OLD HOSE OFF, REVERSED PROCEDURE TO INSTALL NEW HOSE. TOTAL TIME ABOUT 10 MINUTES. Read more
Directs water from inlet valve to detergent dispenser in LG washers. Replace if hose is cracked, leaking, won't stay attached, or damaged from wear.
I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more
Fix a loose or missing fabric softener cap that won't stay in place or causes drawer issues. Simple snap-in replacement restores proper dispensing.
Took top off and did a line at a time Read more
Fix DE door error codes or doors that won't latch with this washer door latch hook. Simple 15-minute DIY repair with video guide. Secures door during cycles.
Changed out door switch and door latch hook. Watched video it was so easy. Appliance Parts Pros save me hundreds of $$$$. This is the 3rd time I used this company I must say they are the best. Read more
Bleach dispenser funnel for LG front load washers. Installs in detergent drawer to safely dispense bleach. Replace if cracked, broken, or missing.
The error code was E0 and this indicated that there was a drainage issue with the washer. I bought a new drain pump motor and a front seal gasket from Appliance parts pros, watched the installation video and installed the parts. The video was direct and straight forward. Everything is working very well again Read more
This inlet hose routes water from the fill valve into your washer. Replace if cracked, leaking, or worn to prevent water damage and drips.
Seals the temperature sensor where it passes through the washer tub. Replace if worn or leaking to prevent water damage. Confirm fit with your model.
Seals the opening between your front-load washer door and tub to prevent leaks. Replace when torn, deformed, or leaking. Confirm fit with your model.
I sat an watched a wash cycle. When it came to drain cycle I could hear the pump making a grinding noise! Door bellow seal leaked too. I ordered new pump and housing,new door bellows seal. The clearance of the pump impeller and housing are real important. I have jet Skies and I knew it is an issue. Watched the video on the repair. Gave me all the instructions to take it apart. One thing it did not show. Lube the new seal mating surface with laundry detergent. It went right on. I have never... Read more
Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.
I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful. Read more
Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.
I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars... Read more
Factory mounting screw for washer tub assemblies, panels, and brackets. Replaces stripped, corroded, or missing screws to secure components properly.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.
Replacement Read more