Dryer Belt

Best Seller

Genuine Whirlpool part

Dryer Drum Belt 92-1/4" 4-Rib

4.9 (1840)

By: Whirlpool

Part Number: 341241

Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.

Why this belt?

Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.

Fixes these common dryer problems

Problem	How the belt solves it
Drum won’t turn	Transfers motor rotation to drum
Loud squealing / thumping	Replaces stretched or frayed belt
Burning-rubber smell	New belt stops slippage & heat build-up
Damp clothes / long cycles	Restores correct drum speed & airflow

DIY install — about 15 minutes

Unplug dryer; remove lint screen housing & front panel.
Release belt tension at idler pulley; lift drum slightly to slide old belt off.
Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
Re-assemble, run test cycle - enjoy quiet, consistent tumbling.

This part fixes the following symptoms

Heat stays on after drum has stopped
Will not tumble
Touchpad does not respond
No heat or not enough heat

Do-It-Yourself Stories from Customers like You Broken dryer belt Bob B. • St Louis , MO • September 12, 2015

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

$14.64

Compare At:: $17.42
You Save:: $2.78

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Ge part

Defrost Timer (Mechanical)

4.8 (5)

By: Ge

Part Number: WR9X482

This mechanical defrost timer controls the refrigerator's automatic defrost cycle, clearing frost from the evaporator and helping maintain stable temperatures. Replacing a faulty timer restores regular defrost intervals to prevent frost buildup and inconsistent cooling.

Cycles the system between cooling and defrost at set intervals to remove frost from the evaporator coils
Heavy frost on the freezer back wall or evaporator cover may indicate a failed timer
Fresh food section warming while the freezer seems cold, or unit stuck in defrost with no cooling
Compressor runs continuously or never restarts; timer does not advance as expected

What's included: 1 defrost timer Install notes:

Disconnect power before servicing to avoid electrical shock
Access location varies by model; commonly in the control housing, behind the kick plate, or at the rear near the compressor
Photograph or label wiring and transfer wires one at a time to the matching terminals
Mount securely, restore power, and confirm normal cooling/defrost operation

Do-It-Yourself Stories from Customers like You Ge refrigerator was not cooling as normal Richard W. • Washington , IL • September 30, 2014

This unit has a recurring problem with the defrost timer. after the first 10 years the original part gave up. we had it replaced and (as normal for me i watched very closely) . after 2 years the same trouble started again. the defrost cycle would run to long. so i replaced the same part and solved the trouble again. so now about every 2 years this part wears out again and i order it and replace it. this has gone on for 20 years now and this unit is still going strong after serving us for 29... Read more

$86.29