Control Board

• Timer will not advance

Based on an internet search, the likely problem seemed to be a bad timer-control switch because it would hum and click but not advance on a 17-year old washer. Repairman diagnosed the problem as a bad lid-switch-assembly and replaced it - problem solved. Now I need to return the Timer-Control. AppliancePartsPros was very quick to ship the Timer-Control and have a great return policy for an unneeded part. Read more

• Timer will not advance

I followed troubleshooting guide and repair videos offered on website, ordered replacement oven control board and reinstalled unit using only a 1/4 inch nut driver. Easy fix for do it yourselfer in 15-20 minutes. Make certain to have model number of appliance when ordering. Parts are somewhat pricey but AppliancePartsPros. were much more reasonable than local parts supply houses or other sources plus they offered 1 year replacement even on electrical stuff. Read more

Used ohm meter on all thermostats and element.everything looked good.wasnt getting power to element unless you wiggled timer knob .ive used this website a bunch because it beats everyone else's prices Read more

Replaced the Main Control Board Assembly along with the evaporator and condenser fan motors. I thoroughly cleaned the very very dirty condenser with a 4$ brush offered by the parts specialist and while I was at it, I changed the door seals and replaced one of the door trays. Beats the crap out of spending $10,000 on a new refrigerator that because of Covid 19 wouldn't be here before the middle of November. Thank you Matt for your help! Read more

This was a newer GE Monogram side-by-side unit that used an inverter compressor. I removed the inverter and used an ohmmeter to measure the resistance of each of the three windings. They were all very close to one another: about 6.8 ohms per winding. I concluded that the compressor was probably not at fault. The inverter kind of burned or chemical-ish, and, when opened, showed an electrolytic capacitor had burst. I replaced the inverter with an overnight part from Amazon. It was the same... Read more

Replaced control module. Read more

Ordered a new mother board install was easy and everything is working great. Web site was easy to navigate . Part came in one day.Thank you Read more

After looking for solutions online and watching some short videos, we decided to open the dishwasher up and try to fix it ourselves. We opened it up and found the circuit board had burned out causing a horrible odor. We ordered our new board, popped it in and we now have a working dishwasher. Hooray! Read more

Removed bad board and replaced with new board Read more

• Timer will not advance

I searched online and found Appliance Parts Pros to have the best price and an instructional video on how to replace this part. I've never done any type of repairs on a washing machine and figured I would give it a try. My washer is approx. nine years old and in good condition, and either I would repair this on my own or buy another. It took me about 30 min. to remove and replace the part, once this was completed I put the washing machine back into operation. Hurray!!!!!! did not have to spend... Read more

We have a Frigidaire LGHS2667KE0. I’m not an appliance technician. Our refrigerator was not working. We were getting an error code SY CE on the front control panel. I tried unplugging it for about an hour and plug it back in. The refrigerator would cut off and on for about 30 seconds, shut down and beep leaving me with the same code. I called an appliance repair technician who pulled the main board from the front bottom of the refrigerator. He believed it was a relay and or the... Read more

After much reading on line regarding my problem. I decided to do any test that I could to try to diagnose and fix this myself if I could. This took a lot of time and patience to get the answers on how to go about this from "experts" as some of the info was contradictory. I was almost about to give up and buy a new washer with less electronic parts and buttons as advised by an honest appliance technician . I tried one more thing first which was to disconnect the lead wires connected to the MCU .... Read more

Called an appliance guy, who said the control panel needed to be changed and quoted me $600. Luckily I Googled the model number and found this website. After seeing that several other people had had the same problem and that the membrane was recommended (not the control panel), I took a chance and ordered the part. One of the other posters recommended a Japanese YouTube video which I easily found and watched first. I highly recommend watching the video first. It's not a hard repair but he... Read more

The defrost heater element looked good and had continuity. The defrost thermostats checked good, so that just left the Defrost Module as the likely suspect. I installed a new defrost control module and thermostats. The thermostats were inexpensive and the old ones could have been intermittent, The only "tricky" part was finding out how to get to the back screw that holds the main control panel. Discovered that the return air duct surrounding the control panel needed to come off. It helps... Read more

Unplugged the stove. Removed the back of the control panel. Removed and replaced the membrane keyboard and the main PCB. Reassembled the stove and everything was back to normal. The PCB was probably ok but I wanted to be sure and get the stove working as soon as possible so I replaced both parts at the same Read more