Gasket & Seal

This magnetic door gasket creates a tight seal around the refrigerator door opening to keep cold air in and warm air out. A fresh, pliable gasket helps maintain temperature, reduce frost buildup, and improve efficiency.

• Forms an air-tight magnetic seal between the door and cabinet
• Helps prevent temperature swings, condensation, and frost around the door
• Common failure signs: torn/cracked rubber, gaps at the corners, door not sealing, moisture or frost near the door
• Restores proper door closure to protect food freshness

• Unplug the appliance and remove food from the door before starting
• Soften the gasket in warm water or with gentle heat to ease installation and improve fit
• Loosen perimeter screws or trim as designed, seat the gasket groove fully, then retighten evenly
• Check for uniform contact all around; adjust door alignment if needed

This replacement seal restores a tight barrier at its mounting point in your appliance. It helps prevent leaks and maintains performance by ensuring a proper fit between connected components where fluids or air must be contained. Location varies by model.

• Creates a reliable seal between mating parts to contain water or air
• Helps stop drips, seepage, and unwanted airflow that can affect performance
• Replace if cracked, flattened, swollen, or leaking
• Common symptoms: moisture under/around unit, residue, or diminished efficiency
• Direct-fit replacement to match the original part's size and profile

• Disconnect power and, if applicable, shut off water supply before servicing
• Note the original seal's orientation; clean and dry all sealing surfaces
• Lightly moisten or use only manufacturer-approved lubricant; avoid petroleum products unless directed
• Seat evenly without twisting; after reassembly, run a test cycle and check for leaks

This oven door gasket forms a heat-resistant seal between the door and the oven frame. It keeps heat inside the cavity to help the oven reach and maintain set temperatures while limiting steam and odor escape.

• Seals the perimeter of the oven door opening to minimize heat loss and drafts
• Supports accurate temperature regulation and more even baking results
• Helps reduce heat transfer to surrounding surfaces and trim
• Common signs of wear: visible tears or flattening, heat leaking at the door, longer preheat, or temperature fluctuations

• Disconnect electrical power; shut off gas supply
• Pull the old gasket straight out of the door's mounting holes, noting corner orientation
• Press the new gasket's end tabs fully into the holes and seat evenly around the frame—do not stretch
• Close the door and check for uniform contact all around

Freezer Door Gasket

Length: Approx. 82 1/2"

This refrigerator door gasket restores a tight seal around the door perimeter. Replacing a worn seal helps keep cold air in, block warm, humid air out, and maintain proper temperatures and efficiency.

• Creates the compression seal between the door and cabinet when closed
• Helps reduce frost, condensation, and temperature swings
• Replaces gaskets that are torn, cracked, warped, or no longer sealing
• Common symptoms: visible gaps, doors not closing fully, moisture around the door, or longer run times

• Disconnect power before servicing
• Warm the gasket in hot water or with a hair dryer on low to relax folds; do not overheat
• Start at the corners and press the gasket lip into the door liner groove, then work along the sides
• Close the door and check for uniform contact around the perimeter; level/adjust hinges if needed

Right hand side. Used most Admiral, Crosley, Norge, and Magic Chef dryers. Includes glide and felt pad.

This window gasket fits between the appliance's window glass and the surrounding frame. It cushions the pane and helps seal gaps so the window stays secure, reduces rattles, and maintains proper performance around the viewing area. What it does:

• Seals the perimeter of the window glass to the door/frame
• Cushions the glass to reduce vibration and rattling noises
• Helps limit unwanted air/heat/steam leakage around the window area
• Common signs of wear: torn or flattened gasket, visible gaps, loose or shifting glass

• 1 window gasket

• Disconnect power and allow all surfaces to cool before starting
• Support the door and glass; wear cut-resistant gloves and eye protection
• Note the gasket's orientation; seat it evenly without stretching or twisting
• Reassemble and verify an even, continuous contact around the window

This oven door gasket forms a heat-resistant seal between the door and the oven frame to keep heat in the cavity. A fresh seal helps the oven preheat properly and maintain consistent temperatures while limiting hot air from escaping.

• Provides a tight thermal seal around the door to reduce heat loss
• Helps stabilize oven temperature and preheat performance
• Replace if the gasket is torn, frayed, brittle, shrunken, or flattened
• Common symptoms of a worn seal: hot air leaking at the door, uneven baking, odors or smoke escaping

• Disconnect power and allow the oven to cool completely
• Remove the old gasket from its channel or end clips; note orientation and seam location
• Clean the groove; press the new gasket in place without stretching, seating corners and ends fully
• Confirm the door closes evenly and seals all around; if not, inspect hinge and latch alignment

This conduit seal fits the dishwasher's water-feed conduit connection, keeping wash water contained and pressure steady to the spray arms. Replacing a worn seal helps address leaks and maintain reliable cleaning performance.

• Seals the joint where the dishwasher's water feed conduit/tube connects within the wash system
• Helps prevent water leaks at the conduit connection point
• Maintains proper wash pressure for consistent spray performance
• Common signs of failure: drips beneath the unit, visible cracks/flattening, or a loose-fitting old seal

• Disconnect power and shut off the water supply before servicing
• Access the conduit connection (location varies by model), remove the old seal, and clean mating surfaces
• Lightly moisten the new seal to ease installation and seat it fully
• Reassemble and run a brief cycle to check for leaks

This rubber seal creates a tight barrier between mating components to keep water contained and stop drips. Replacing a flattened or cracked seal helps prevent leaks and protects nearby parts from moisture-related damage. What it does:

• Forms a watertight gasket between two parts in the assembly
• Helps prevent drips or seepage at the connection point
• Restores proper compression when the original seal hardens or deforms
• Common signs of failure: leaks, dampness, or visible cracking/flattening of the old seal

• 1 rubber seal

• Disconnect power; for water-bearing assemblies, shut off the water supply
• Access the seal location per your service information and note orientation/depth before removal
• Clean mating surfaces; lightly moisten the new seal with water or mild soap to ease installation
• Ensure the seal is fully seated, reassemble, and test for leaks

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated

This cap seal creates a tight barrier between a cap and its mating surface in your appliance. Replacing a worn seal restores a secure, leak-resistant fit and helps maintain proper performance over time.

• Forms a tight seal where the cap seats to prevent leaks and seepage
• Helps maintain intended pressure/flow and keeps contaminants out
• Typical failure signs: drips or moisture around the cap area, loose cap fit, or a flattened/cracked seal
• Age, heat, and detergents/chemicals can harden or deform the seal

• Disconnect power and shut off water before servicing
• Remove the cap and note the seal's orientation
• Clean mating surfaces; seat the new seal fully without twisting
• Reinstall the cap and test operation, checking for a leak-free fit

Color: White

The Door Gasket is an OEM part for Whirlpool refrigerators. It forms an insulating perimeter around the freezer door opening to prevent warm air from entering during use.

Causes of a faulty door gasket include breakdown of sealing materials over time, cracks or loose edges that compromise effectiveness.

Symptoms of a bad freezer gasket are:

• Frost or ice buildup around the door seal
• Visible gaps allowing warm, moist air inside
• Inefficient cooling requiring excessive energy use
• Higher electric bills from poor insulation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This surface burner gasket seals the burner assembly to the cooktop. Replacing a worn gasket restores a tight seal to help support reliable ignition, a stable flame, and keeps spills and moisture from entering the burner well. What it does:

• Seals between the surface burner assembly and cooktop
• Helps maintain proper airflow for consistent ignition and flame
• Helps prevent liquids, crumbs, and grease from seeping below the burner
• Common symptoms of failure: distorted or hardened gasket, visible cracks, uneven/weak flame, or persistent clicking during ignition

• 1 gasket

• Disconnect power and shut off gas supply; allow the appliance to cool completely
• Remove grate, burner cap, and burner head to access the gasket
• Clean mating surfaces; seat the gasket flat and do not use sealants or adhesives unless specified by the manufacturer
• Reassemble, restore gas, and verify burner operation; leak-check with soapy water if any gas fittings were disturbed

This is a Whirlpool freezer gasket.If the freezer is having difficulties staying at temperature and the old gasket is damaged or off track, replacing the gasket could fix the problems. A faulty gasket could also lead to higher levels of ice and frost build up in the freezer. This could potentially raise an energy bill because it causes the freezer to stay engaged longer. Higher levels of frost build up could ultimately damage other components. Pull the old gasket out before installing the new one. It doesn't matter if the old part gets snagged or torn when it's taken out since a replacement is ready. Be sure not to break any of the fastening clips around the edge of the freezer. Slowly insert the gasket around the outer edges of the freezer lid, inserting the lip of the gasket into the cut out areas. Make sure the gasket is held tightly in place before shutting the freezer lid.This part is sourced directly from the manufacturer as a genuine OEM replacement part. This gasket is only available individually and is not included with any other parts or the original appliance. This product is compatible with Whirlpool brand freezers.