Gasket & Seal

• Marks left on clothes

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

By replacing it Read more

Purchase a new one and installed per your video on Youtube. Great and easy. Read more

New door seal did the trick. Read more

Went ahead and replaced the pulley as well the drum bearing sleeve and O ring, drum belt and the front drum bearing slides. Put the unit back together and she ran like a top! Read more

Took my time and disasembeld the mixer and cleaned old grease from internal gear box. put new greas in and put it back together. A piece of cake!!!!! Read more

Ordered gaskets. My daughter figured it out .15 min for installation.Refrig has a lot more years. Read more

It was an easy fix the instructions where very helpful, thank you very much Read more

1. Ordered new gasket. 2. Heated with blow dryer gasket until it resumed its normal shape. 3. Turned off refrig. 4. Cleaned freezer compartment. 5. Removed old gasket. 6. Installed new gasket. 7. Turned on refrig. 8, Operation back to normal in about 6 hours. Read more

Really easy project. Ordered the replacements and after arrival removed worn gaskets and replaced with new. Main thing is to make sure your replace in same direction as originals and make sure you secure gasket in groove. Read more

The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more

First, I removed the old gaskets, which was a very easy task since they are held in the doors by rubber beads in recessed slots. I installed the new right door gasket in less than 10 minutes by gradually pushing the retainer bead into the door recessed slot with finger pressure until it was seated properly. The left door bead was somewhat more difficult to install into the bead slot, because the recessed bead slot is covered by a hinged flap on its left edge that doesn't permit easy access.... Read more

• Door sweating

The freezer door on my 12-yr old GE side-by-side refrigerator/freezer would not stay completely shut resulting in temperature variations and ice buildup from outside humidity seeping into the freezer compartment. These problems were exacerbated by the fact that this appliance is located in my garage in the heat / humidity of the Atlanta, GA area. I applied a thin layer of petroleum jelly to the gasket which improved the seal but did not completely solve the problem. I discovered that... Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

Replaced all 3 gaskets with gaskets from appliancepartspros.com. Gaskets took less than 10 minutes to replace and fit perfect! I checked the refrigerator and freezer compartments approx 6 hrs later and found the compartments to be a few degrees colder. Freezer ice was cold and loose, not stuck together. It's like having a new refrigerator! Read more

• Leaking

First, DO NOT call Sears for parts, their call center knows nothing about the product. App-Pros are the best for help and the right parts. I figured to repair, replace all seals and any item that shows need to and all items that have to do with the spin that may be bad. Repair videos great help. I will start from the "bottom" up, the repairs were not done in this order, just a list of what I did and notes. Replaced-- motor drive coupling, (checked out transmission ok), thrust washer,... Read more