Parts for Kenmore 795.74302810 (79574302810, 795 74302810): Other Parts

This is a factory-style screw used to secure components and panels on compatible LG appliances. It restores proper fit and reduces movement where a missing or stripped screw causes parts to sit loose. What it does:

• Fastens panels, brackets, or trim to appliance chassis to restore secure attachment
• Stops rattling or vibration caused by loose or missing fasteners
• Helps maintain proper alignment of removable parts for safe operation
• Serves as a direct replacement when the original screw is lost or damaged

• Screw

• Use the matching screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent damage to threads or plastic parts
• Replace only with the specified OEM screw to ensure fit and function
• Disconnect power to the appliance before accessing internal components when applicable

This hinge bolt secures the hinge to the appliance cabinet or door, keeping alignment true and motion smooth. Replacing a stripped, missing, or corroded bolt helps restore proper door operation and reliable closing.

• Fastens the hinge to support and stabilize the door
• Helps maintain alignment for smooth opening and closing
• Replaces damaged, stripped, or missing hardware

• Disconnect power to the appliance; shut off water supply if applicable
• Support the door to prevent strain on remaining hardware; enlist a second person if needed
• Note the order/orientation of any shims or washers and transfer them during reassembly
• Start threads by hand to avoid cross-threading; tighten securely without overtightening

This screw is a direct-fit replacement fastener that secures panels, brackets, and internal components. Replacing a missing or stripped screw helps stop rattling and keeps parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets, or internal components to restore proper fit
• Replaces missing or damaged hardware that can cause rattling or loose parts
• Restores alignment so doors, shelves, or assemblies operate smoothly
• Provides a straightforward hardware fix without replacing larger assemblies

• Use the matching screwdriver or driver bit to avoid stripping the head
• Do not overtighten — snug until seated to avoid damaging threads or plastic parts
• Disconnect power or follow appliance safety instructions before servicing electrical areas
• Keep removed hardware organized and save any damaged parts for inspection

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

This is a customized screw used to secure components in LG appliances. It replaces a worn or missing fastener to restore proper assembly and reduce rattling or loose panels. What it does:

• Secures panels, brackets, or small components in the appliance chassis
• Helps stop vibration-related noise caused by loose fasteners
• Replaces missing or stripped screws to restore safe, stable assembly
• Matches OEM fit for the specific mounting point it was made for

• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can damage threads or parts
• Disconnect power and follow appliance-specific safety procedures before servicing

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This drain tube assembly channels defrost water from the evaporator to the drain pan, preventing leaks and water buildup. Replace a cracked or clogged tube to restore proper drainage and reduce puddles or ice inside your refrigerator.

• Directs defrost water from the drain outlet to the drain pan
• Helps prevent water leaks inside the fresh food or freezer compartment
• Addresses issues from a tube that is cracked, kinked, or obstructed by debris/ice
• Common symptoms: water under crisper drawers, puddles beneath the unit, or ice forming at the freezer bottom

• Unplug the refrigerator before servicing
• Access the drain outlet and remove any ice or debris from the drain path
• Fully seat the tube at both ends to ensure a secure, leak-free fit
• Test by pouring a small amount of warm water into the drain to confirm proper flow to the pan

This adjustable leveling leg assembly supports and stabilizes your appliance by threading into the base frame. Replacing a worn or missing leg helps you level the unit for smoother, quieter operation on uneven floors.

• Provides height adjustment to level the appliance and distribute weight evenly
• Helps prevent rocking, wobbling, and excess vibration or rattling
• Can improve door alignment and smooth opening/closing when the cabinet is properly leveled
• Useful when a leg is missing, damaged, or threads are stripped

• Disconnect power; if applicable, shut off the water supply
• Use a helper to safely brace or tip the unit; protect flooring when accessing the leg
• Unthread the old leg and hand-thread the new one; tighten as needed
• Adjust front-to-back and side-to-side until stable; all legs bear weight evenly

This DC motor assembly replaces the appliance's main DC drive motor to restore reliable motor-powered operation. It provides the exact-fit motor needed to regain normal mechanical function and reduce downtime. What it does:

• Drives the appliance's motorized components so the unit can run as intended
• Stops motor-related failures like no-spin, no-run, or intermittent operation
• Helps resolve motor humming or erratic movement when the motor is the cause
• Works with the appliance's existing mounting and electrical connections when compatible

• Disconnect power before servicing to avoid shock or injury
• Replacement typically requires removing panels and disconnecting electrical connectors—keep track of fasteners
• Inspect wiring harness and connectors for damage before reassembly

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

The Shelf Assembly is an OEM replacement part for LG refrigerators. It provides a movable shelf surface for organizing and storing items in the refrigerator or freezer compartment. 

Symptoms of a bad shelf assembly include:

• Sagging or bowing of the shelf surface 
• Difficulty in moving or removing the shelf
• Damage or cracks in the frame or wire grid
•  Inability to bear weight as intended

Causes of failure can be repeated overloading, accidental impacts, or normal wear and tear over time. 

This authentic LG shelf assembly is also compatible with refrigerators by Kenmore models.

The Freezer Tray is an OEM part for LG refrigerators. It provides a convenient and organized space for storing frozen foods, ensuring they remain easily accessible and properly arranged within the freezer compartment.

Causes of a bad freezer tray can include cracks or breaks from heavy items, warping due to temperature fluctuations, or general wear from frequent use. A damaged tray can lead to improper storage and difficulty in organizing frozen items.

Symptoms of a bad freezer tray include:

• Cracks or splits in the tray
• Difficulty sliding the tray in and out
• Warping or bending
• Reduced storage capacity

This OEM LG part is also compatible with Sears/Kenmore.

This drawer tray assembly forms the shelf/base that supports a slide-out bin inside the refrigerator. Replace a cracked or warped tray to restore stable food storage and smooth drawer movement.

• Supports a slide-out drawer and food items in the fresh food or freezer section
• Helps drawers track correctly and sit level
• Damage can lead to binding drawers, tilting contents, or reduced storage
• Common signs: cracked plastic, sagging tray, drawer hard to open/close, visible wear

• Disconnect power and remove food from the affected area
• Slide out and remove the drawer(s) resting on the tray
• Lift out the damaged tray; transfer any reusable trim from the original if applicable
• Seat the new tray fully in the supports and reinstall the drawer(s)

The Tray Assembly Drawer is an OEM part for LG refrigerators. This tray assembly provides organized storage space in the freezer section, making it easier to access and manage frozen items.

Over time, freezer tray assemblies can become damaged due to regular use, accidental impacts, or overloading with heavy items. Damage can also occur if the drawer is forced open or closed when obstructed.

Symptoms of a bad freezer tray assembly include:

• Difficulty sliding the drawer in and out
• Cracks or breakage in the tray or its components
• Items not staying securely in place within the drawer

This OEM LG part is also compatible with Sears/Kenmore models.

The Tray Assembly Drawer is an OEM part for LG refrigerators. This tray assembly provides organized storage space in the freezer section, making it easier to access and manage frozen items.

Over time, freezer tray assemblies can become damaged due to regular use, accidental impacts, or overloading with heavy items. Damage can also occur if the drawer is forced open or closed when obstructed.

Symptoms of a bad freezer tray assembly include:

• Difficulty sliding the drawer in and out
• Cracks or breakage in the tray or its components
• Items not staying securely in place within the drawer

This OEM LG part is also compatible with Sears/Kenmore models.

The Freezer Tray is an OEM part for LG refrigerators. It provides a convenient and organized space for storing frozen foods, ensuring they remain easily accessible and properly arranged within the freezer compartment.

Causes of a bad freezer tray can include cracks or breaks from heavy items, warping due to temperature fluctuations, or general wear from frequent use. A damaged tray can lead to improper storage and difficulty in organizing frozen items.

Symptoms of a bad freezer tray include:

• Cracks or splits in the tray
• Difficulty sliding the tray in and out
• Warping or bending
• Reduced storage capacity

This OEM LG part is also compatible with Sears/Kenmore.

This shelf net is a replacement mesh shelf for refrigerators that helps keep bottles and small items secured and organized on a fridge shelf. Restores containment for torn or sagging nets. What it does:

• Provides a flexible mesh surface to hold bottles, cans and other items in place
• Prevents small items from falling through or shifting during door access
• Replaces torn, stretched or sagging shelf nets that no longer secure contents
• Helps restore original shelf function and appearance

• Disconnect power or unplug the refrigerator before starting any repair
• Remove food and the affected shelf before replacing the net
• Typically installs by fitting the net into the dedicated shelf frame or clips; for exact instructions
• Wear gloves to avoid sharp edges on shelf frames during installation

This refrigerator glass shelf assembly replaces a broken, cracked or missing interior shelf so you can safely store food and restore usable shelving space. Tempered glass shelf with frame supports everyday fridge organization. What it does:

• Provides a stable, easy-to-clean surface for storing food and containers
• Replaces cracked, chipped or shattered glass shelves that cause leaks or safety hazards
• Prevents items from falling through open shelf openings and helps maintain internal organization
• Fits into existing shelf rails and rests on factory shelf supports

• Disconnect power and remove food before installing to avoid spills and injury
• Handle tempered glass carefully; wear gloves to protect hands during installation
• Slide shelf into existing rails until it seats securely on factory supports
• If shelf support clips or rails are damaged, replace them before installing this shelf

This rail holder is a small replacement mounting clip that secures a rail or guide in place so racks or sliding components stay aligned and operate smoothly. It restores proper fit and reduces shifting or rattling during use. What it does:

• Secures the appliance rail or guide to prevent the rail from coming loose
• Keeps racks or sliding parts aligned for smooth movement
• Reduces vibration and rattling caused by a loose rail
• Helps prevent minor wear from misalignment or shifting components

• Disconnect power (or unplug) and remove any obstructing parts before replacing the holder
• Replacement typically requires basic hand tools; retain all fasteners and note orientation
• Inspect mating rail and fasteners for damage; replace any worn parts to ensure a secure fit

This fresh room tray assembly restores the dedicated deli/snack drawer in your refrigerator. Replace a cracked, warped, or missing bin to keep foods organized and ensure smooth, reliable access.

• Provides a smooth-sliding storage bin for deli/snack items in the fresh food section
• Restores organization and usable space when the original tray is broken or missing
• Fits on the existing fresh-room rails/shelf designed for this drawer
• Symptoms it can resolve: cracked or broken tray, hard-to-slide drawer, missing bin

• Open the refrigerator and clear the area around the drawer location.
• Pull the old tray straight out; lift or tilt to clear the stops as your model requires.
• Align the new tray with the side rails and slide it in until fully seated.
• Handle plastic carefully to avoid damage; do not force the drawer.

The Slide Rail is an OEM part for LG refrigerators. This part allows the smooth and stable operation of the freezer drawer, allowing it to slide in and out. The slide rail supports the weight of the drawer and its contents, facilitating easy access to frozen items while maintaining proper alignment. The rail measures approximately 16” x 2”

Causes of a bad slide rail can include wear and tear from frequent use, physical damage from overloading the drawer, and the accumulation of debris or ice buildup that can obstruct the sliding mechanism.

Symptoms of a bad slide rail for the freezer drawer include:

• Difficulty in sliding the freezer drawer in and out
• The freezer drawer not staying in place or coming off the rails
• Unusual noises such as grinding or squeaking during movement
• Visible damage, bending, or rust on the rail

This OEM LG part is also compatible with some Kenmore models.

The Rail Guide Assembly is an OEM replacement part for LG bottom-mount refrigerators. It contains telescopic extension rails and channel brackets that accommodatingly glide freezer and fridge shelves in and out with simplicity. This assembly facilitates effortless access to every stored item.

Causes of part malfunction relate to prolonged retraction/extension stressing roller bearings and metal rails to the point of fatigue cracks or binding issues hindering smooth sliding.

Symptoms involve:

• Shelves that resist extension or fail to fully retract into fridge cavities
• Grating noises and vibrations emerging from misaligned or strained rails
• Inconvenient access as capacity-flexible shelving gets restricted

This OEM replacement part is compatible with LG and Kenmore bottom-mount refrigerators.

The Freezer Drawer Rail Assembly is an OEM part for LG refrigerators. This assembly includes the rails that support and guide the freezer drawer, allowing it to slide in and out smoothly for easy access to frozen foods.

Causes of a bad freezer drawer rail assembly can include wear and tear over time, buildup of ice or debris, or damage from excessive force or impact. A compromised rail assembly can hinder the drawer's movement and affect the overall functionality of the freezer.

Symptoms of a bad Freezer Drawer Rail Assembly include:

• Difficulty opening or closing the freezer drawer
• The drawer not staying aligned or on track
• Unusual noises when operating the drawer
• Visible damage or wear on the rails

This OEM LG part is also compatible with Sears/Kenmore.

This right-side Freezer Basket Support Rail is an OEM part for LG refrigerators. Located inside the freezer compartment, it provides elevated storage shelves for ice cream, frozen vegetables, meats, and more above the freezer floor.

Causes of a bad support rail can include damages such as cracks or breaks that compromise its load-bearing ability over years of use. Sharp freezer temperatures cause constant contraction and expansion.

Symptoms of a bad support rail include:

• Baskets or containers unstable and prone to tipping
• Reduced storage capacity within the freezer
• Safety concerns if a cracked rail were to fully collapse

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Freezer Basket Support Rail is an OEM part for LG refrigerators. This component is essential for supporting and guiding the freezer basket, allowing it to slide in and out smoothly. The rail measures approximately 13 x 2 inches.

Symptoms of a failing Freezer Basket Support Rail include:

• Difficulty sliding the freezer basket in and out
• Unusual noises such as grinding or squeaking when moving the basket
• The basket becoming misaligned or tilting when pulled
• Visible wear or damage to the rail

Causes of a bad support rail often include mechanical stress from overloading the basket, frequent use which can wear down the material, or accidental damage during cleaning or rearranging items within the freezer.

This OEM LG part is also compatible with Sears/Kenmore.

This tray cover assembly replaces a cracked or warped cover that supports the refrigerator bin/tray. Restoring a level, secure surface helps keep items stable and allows the drawer to move and seat properly. What it does:

• Forms the shelf/cover above a refrigerator drawer or tray
• Supports items stored above and aligns the bin beneath
• Replaces cracked, sagging, or broken frames and tabs
• Helps prevent spills and binding when opening or closing the drawer

• Includes 1 tray cover assembly

• Unplug the refrigerator and clear the compartment for safe access.
• Slide out and remove the bin/tray; lift the old cover off its support rails or tabs.
• Position the new cover; ensure all tabs fully engage before reinstalling the bin and checking movement.

This rail guide assembly supports and aligns a refrigerator drawer so it slides smoothly along its track. Replacing a worn rail restores easy operation and helps prevent binding, sagging, or uneven travel when opening and closing.

• Supports and guides the drawer/bin along the cabinet track
• Helps the drawer open and close smoothly and stay level
• Maintains proper alignment so the drawer seats correctly
• Common symptoms: drawer hard to slide, tilts or binds, rough/noisy travel, visible cracks or damage on the rail

• Disconnect power and remove drawer contents for safety
• Pull out and lift the drawer/basket off the rails to access the mounting points
• Remove screws/clips, transfer any brackets or end caps from the old rail, and install the new assembly
• Re-engage the drawer on both rails and test for smooth operation before reloading

The Crisper Drawer Slide Rail is an OEM part for LG refrigerators. It is designed to support and guide the crisper drawer, allowing it to slide in and out smoothly for easy access to your fresh produce. The rail measures approximately 20 x 6 inches,

Over time, the slide rail can wear out or become damaged, affecting the operation of the crisper drawer. Common causes of a bad crisper drawer slide rail include repeated use, accidental impact, or the accumulation of debris and residue that can hinder movement.

Symptoms of a bad crisper drawer slide rail include:

• Difficulty sliding the crisper drawer in and out
• The drawer not staying securely in place
• Unusual noises when using the drawer
• The drawer becoming misaligned or falling out of the track

This OEM LG part is also compatible with Sears/Kenmore models.

This case assembly is the outer housing for the refrigerator's Magic Room compartment, restoring the compartment's structure and proper fit so shelves and interior components mount securely. What it does

• Replaces damaged or cracked Magic Room housing that can prevent proper shelf support or alignment
• Restores correct interior spacing so drawers and accessories install and operate correctly
• Helps stop drafts or misalignment that can affect compartment sealing and temperature control
• Provides the mounting surface for related trim, shelves, and fasteners

• Disconnect power and, if applicable, turn off the water supply before beginning service
• Remove interior shelves, drawers, and trim to access and remove the old housing
• Align tabs and mounting points carefully; use original fasteners and avoid over-tightening screws

This ferrite magnet is a replacement magnetic element used in compatible appliance assemblies to help secure components and maintain proper alignment. It restores magnetic retention and reduces shifting or misalignment during operation. What it does:

• Provides magnetic retention for panels, assemblies or components that rely on ferrite magnets
• Helps maintain proper alignment and secure closure where magnets are used
• Can reduce noise and vibration related to loose magnetic components
• Useful when a brittle, cracked or weak magnet no longer holds parts in place

• Disconnect power and follow the appliance manufacturer's safety instructions before servicing
• Handle the magnet carefully; ferrite material is brittle and can chip or shatter if dropped or struck
• Keep magnets away from sensitive electronics and credit cards; avoid pinching fingers between strong magnets
• If the original magnet is bonded or embedded, some adhesive or light trim may be needed for proper fit.

This replacement door gasket creates a tight seal around the refrigerator door to help keep cold air in and warm, moist air out. Restores proper sealing to help maintain temperature and reduce frost or moisture buildup. What it does:

• Seals the refrigerator door to maintain consistent internal temperatures
• Helps prevent moisture, frost, and condensation inside the fresh-food compartment
• Reduces air leaks that can cause the fridge to run more frequently or uneven cooling
• Common symptom: visible gaps, torn or compressed seal, or moisture/frost near the door edge

• Disconnect power to the appliance before starting any work.
• Remove the old gasket carefully; inspect and clean the gasket channel and mating surface before installing the new seal.
• Warm the gasket slightly or work around the perimeter to seat it evenly; avoid overstretching.
• If clips or adhesive are used on your model, reuse or replace only the exact fasteners specified by the manufacturer.

Replace a cracked or missing door bin with this door basket. It mounts to the refrigerator door to hold bottles and condiments, restoring safe, convenient storage and helping the door close properly.

• Attaches to the inner door to organize bottles and small items within easy reach
• Replaces a bin that is cracked, warped, or has broken locking tabs
• Symptoms include: bin falls off, won't stay seated, spills, or difficulty closing the door
• Restores designed door storage capacity and stability

• Unload the door and lift the old bin up and out of the mounting slots
• Align the new basket with the slots and press down until fully seated on both ends
• Do not force; confirm it's locked in before loading items
• Follow appliance safety guidelines; avoid overloading the bin after installation

This door gasket assembly creates a tight seal around the refrigerator door to help maintain consistent internal temperatures and improve energy efficiency. Replaces a worn or damaged gasket to reduce drafts and moisture buildup. What it does:

• Seals the door to keep cold air in and warm air out
• Helps prevent frost build-up and water leaks inside the compartment
• Restores proper door alignment and consistent cooling performance
• Reduces energy use by preventing air loss around the door

• One door gasket assembly

• Recommended for users comfortable with basic appliance repairs; check OEM instructions for exact fit and orientation
• Inspect door liner and mounting channel for debris or damage before installing
• Warm the gasket slightly for easier installation and to help seat the seal
• Disconnect power to the appliance or follow manufacturer safety guidance when working near controls or lights

This door gasket assembly provides a replacement door seal to help restore a refrigerator's airtight closure and reduce cold air loss. It fits as the primary barrier between the cabinet and door for consistent cooling performance. What it does:

• Seals the refrigerator door to maintain proper internal temperature and reduce energy loss
• Helps prevent moisture buildup and frost by keeping warm air out
• Restores an even door-to-cabinet contact to reduce compressor runtime and cycling
• Addresses common symptoms like warm spots near the door, excess frost, or a door that doesn't close tightly

• One door gasket assembly

• For safety, unplug the appliance before attempting installation
• Verify correct gasket orientation and full seating in the door channel to ensure a proper seal
• Inspect the door frame and mounting channel for damage or debris and clean before installing
• If the gasket is stuck or brittle, warm gently per OEM guidance; replace rather than repair torn gaskets

This drawer guide is the sliding rail that helps a refrigerator/freezer drawer open and close smoothly and stay aligned. It restores stable drawer movement and prevents sticking, sagging, or drawers coming off the track. What it does:

• Guides and supports the drawer as it slides in and out
• Keeps the drawer aligned to prevent binding or uneven movement
• Reduces drawer sag and helps prevent accidental removal
• Restores smooth operation when original guide is cracked, worn, or broken

• One drawer guide

• Disconnect power to the appliance before starting any repair
• Remove the drawer per the appliance service instructions to access the guide
• Replace the guide using the OEM fasteners or clips; keep original mounting hardware unless damaged

The Basket Assembly is an OEM component specifically designed for LG Door-in-Door refrigerators containing bottom-mounted crisper drawers. This integral assembly organizes stored items within the refrigerator doorway.

Symptoms of a bad basket assembly include:

• Cracked or broken perforated shelves  
• Detached mounting brackets failing to secure basket
• Warped contours no longer fitting base compartment
• Missing attachments inhibiting proper installation

Causes of failure involve stresses from repeated loading/unloading cycles, mineral buildup weakening plastic brackets over time, or impact damage compromising structural integrity.

Replace yours today with this genuine OEM LG assembly to maintain tidy organizational capacity. Precision slots provide adjustable shelf positioning optimized for produce, snacks, and beverages. Compatible across Samsung, Frigidaire, and GE models featuring removable door crisper baskets.

This refrigerator door shelf bin replaces a cracked or missing bin on the fresh food door. It snaps into the molded slots to restore secure, convenient storage for condiments, jars, and small bottles. What it does:

• Mounts to the inner door liner to hold items and free up shelf space
• Restores door storage capacity when the original bin is damaged or missing
• Common symptoms: cracked plastic, broken tabs, bin falls off, won't stay seated
• Helps keep jars and bottles organized and easy to access

• 1 door shelf bin

• Remove items from the old bin, then lift it straight up to release from the door slots
• Align the new bin's hooks with the door slots and press down firmly until it locks
• Handle plastic carefully and consider wearing gloves to avoid cuts from sharp edges
• Do not force the bin; ensure it's positioned in the correct door location before securing

This refrigerator door shelf bin replaces a cracked or missing bin on the fresh food door. It snaps into the molded slots to restore secure, convenient storage for condiments, jars, and small bottles. What it does:

• Mounts to the inner door liner to hold items and free up shelf space
• Restores door storage capacity when the original bin is damaged or missing
• Common symptoms: cracked plastic, broken tabs, bin falls off, won't stay seated
• Helps keep jars and bottles organized and easy to access

• 1 door shelf bin

• Remove items from the old bin, then lift it straight up to release from the door slots
• Align the new bin's hooks with the door slots and press down firmly until it locks
• Handle plastic carefully and consider wearing gloves to avoid cuts from sharp edges
• Do not force the bin; ensure it's positioned in the correct door location before securing

This refrigerator door shelf bin replaces a cracked or missing bin on the fresh food door. It snaps into the molded slots to restore secure, convenient storage for condiments, jars, and small bottles. What it does:

• Mounts to the inner door liner to hold items and free up shelf space
• Restores door storage capacity when the original bin is damaged or missing
• Common symptoms: cracked plastic, broken tabs, bin falls off, won't stay seated
• Helps keep jars and bottles organized and easy to access

• 1 door shelf bin

• Remove items from the old bin, then lift it straight up to release from the door slots
• Align the new bin's hooks with the door slots and press down firmly until it locks
• Handle plastic carefully and consider wearing gloves to avoid cuts from sharp edges
• Do not force the bin; ensure it's positioned in the correct door location before securing

The Refrigerator Door Shelf is an OEM part for LG refrigerators. It provides additional storage space on the door of the refrigerator, allowing for the organization and easy access of frequently used items such as condiments, beverages, and small containers. It measures approximately 14" x 4" x 4".

Causes of a bad refrigerator door shelf can include general wear and tear from repeated use, overloading the shelf with heavy items, or accidental damage during cleaning or reorganization. Cracks or breakage in the plastic material can also render the shelf unusable.

Symptoms of a bad refrigerator door shelf include:

• Cracked or broken shelf
• Items not staying securely on the shelf
• The shelf not fitting properly into the door brackets
• Difficulty in attaching or removing the shelf

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

The Refrigerator Door Shelf is an OEM part for LG refrigerators. Designed to offer additional storage space, this door shelf seamlessly integrates into the refrigerator door, providing a convenient spot to store jars, bottles, and other condiments. 

Over time, door shelves may suffer from wear and tear or become damaged due to overloading or accidental impact. This can lead to cracks, breaks, or a loose fit, which compromises the shelf's ability to hold items securely.

Symptoms of a bad Refrigerator Door Shelf include:

• Visible cracks or breaks in the shelf
• The shelf sagging or unable to hold items securely
• Difficulty fitting the shelf into the door slots
• Items falling through the shelf due to damage or warping

This OEM LG part is also compatible with some Kenmore models.

This stopper assembly mounts on the appliance door to cushion movement and hold the door in position, reducing wear and preventing slamming for smoother, safer operation. Fits as the OEM door stop used on compatible LG models. What it does:

• Cushions door movement to prevent hard impacts and reduce noise
• Holds the door in the open or closed position to prevent unwanted swings
• Helps maintain door alignment and reduces stress on hinges and latches
• Common symptom: door slams, won't stay open, or bangs against the cabinet

• Disconnect power and water before starting any repair
• Remove the door or open access for safe replacement
• Replacement typically requires basic hand tools (screwdriver or nut driver)
• Inspect surrounding hinge/fastener hardware and replace if worn

This door stopper assembly mounts at the hinge to control how far the door opens and promote smooth, consistent closing. Replacing a worn or broken stopper restores proper door swing and helps protect the hinge from overextension.

• Limits the door's opening range to prevent overextension
• Guides and cushions door movement for a smoother close
• Helps maintain door alignment at the hinge area
• Common symptoms: door swings too far, doesn't stop at the usual angle, clicks/binds near the hinge, or visible cracks/wear on the stopper

• Disconnect power to the appliance before servicing
• Support the door and use a helper when loosening hinge hardware
• Note the original orientation and transfer any spacers/shims if present
• Tighten fasteners evenly and verify smooth door operation before finalizing reassembly

The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators. This hinge supports the refrigerator door, allowing it to open and close smoothly while maintaining proper alignment. It is designed to handle the weight of the door and ensure a secure and stable operation over time.

Causes of a bad lower refrigerator door hinge can include regular wear and tear, physical damage from overloading or impacts, and gradual loosening over time. A faulty hinge can lead to misalignment, difficulty in opening or closing the door, and potential damage to the door seal.

Symptoms of a bad lower refrigerator door hinge include:

• The door not closing properly or staying open
• Sagging or misaligned door
• Unusual noises when opening or closing the door
• Gaps in the door seal, causing cooling inefficiency

This OEM LG part is also compatible with Sears/Kenmore models.

The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators, designed to support and pivot the refrigerator door, allowing it to open and close smoothly. This hinge is a critical component for the proper alignment and function of the door, ensuring an airtight seal when closed to maintain the internal temperature and efficiency of the refrigerator.

Causes of damage to the lower refrigerator door hinge often include normal wear and tear, excessive force when opening or closing the door, or corrosion due to moisture and cleaning agents. 

Symptoms of a bad Lower Refrigerator Door Hinge include:

• Difficulty in opening or closing the refrigerator door.
• A door that hangs unevenly or does not close properly
• Unusual noises during door operation 
• Visible wear or damage to the hinge itself.

This OEM LG part is also compatible with some Kenmore models.

This slide rail lets a drawer move smoothly in and out, restoring proper alignment and stable operation. Replace a worn or bent rail to stop sticking, uneven travel, or a drawer that comes off its track. What it does:

• Guides the drawer along its track for smooth opening and closing
• Restores even, stable travel and prevents the drawer from catching or binding
• Replaces bent, worn, or damaged rail components that cause misalignment
• Helps keep the drawer aligned to prevent tilting or partial ejection

• One slide rail

• Disconnect power and remove the drawer before replacing the rail when applicable
• Verify rail orientation and slide fully into the track before securing fasteners
• Use basic hand tools; keep removed screws and clips for reinstallation
• If the drawer is heavy, have a second person assist to prevent injury or damage

This guide assembly rail is the replacement drawer slide that restores smooth, stable movement for a refrigerator or appliance drawer. It keeps the drawer aligned and reduces sticking or uneven operation for everyday use. What it does:

• Guides and supports the drawer as it opens and closes to maintain proper alignment.
• Reduces sticking, scraping, and uneven travel caused by worn or damaged rails.
• Helps prevent drawer sagging and improves load stability when pulling out the drawer.
• Works with the factory mounting points and keeps the drawer tracking true.

• One guide assembly rail.

• Disconnect power or follow appliance-specific safety procedures before servicing.
• Remove the drawer or access panel to reach the existing rail; keep fasteners for reuse unless replacement required.
• Compare the new rail to the old part to ensure fit and orientation before installing.
• If fasteners are damaged or missing, replace with OEM-specified hardware.

This guide assembly keeps a sliding appliance drawer or rack aligned for smooth, reliable movement and helps prevent sagging or derailment. It restores proper tracking so the drawer/rack opens and closes without binding. What it does:

• Guides and supports a sliding drawer or rack so it stays aligned during use
• Reduces binding, sagging, or derailment when loading or pulling the drawer/rack
• Eliminates scraping or grinding noises caused by a worn guide
• Helps restore smooth, even motion and proper engagement with the slide mechanism

• One guide assembly

• Disconnect power before starting any repair
• Remove the affected drawer/rack to access the guide; keep track of fasteners
• Align the guide with the slide channel and secure per the OEM fastening points; some designs snap in while others use screws
• If mounting hardware is worn or missing, replace with OEM-specified fasteners for safe operation

This replacement hinge assembly supports and pivots the refrigerator door. Replacing a worn or bent hinge restores smooth door movement and proper alignment so the gasket can seal correctly to help maintain performance. What it does:

• Provides the pivot point for the door to open and close
• Supports the door's weight to keep it aligned
• Helps the door gasket seal evenly against the cabinet
• May correct issues such as door sagging, rubbing, popping, or not closing/sealing fully

• One hinge assembly

• Unplug the refrigerator and remove items from the affected door
• Support the door while removing hinge screws; note the orientation of any spacers/bushings
• Transfer any reusable hardware from the old hinge to the new assembly
• Reinstall and tighten fasteners; verify door is level and check gasket seal

The Freezer Drawer Rail is an OEM component for select LG refrigerators.  Its operatation allows access to frozen foods.  

Causes of a bad rail could include debris accumulation, ice buildup, or physical damage that hinders smooth sliding. Over time, continuous usage may also cause wear of moving parts.

Symptoms of a failed freezer drawer rail include: 

• Resistance or stiffness when opening/closing drawers
• Noisy, squeaking, or grinding sounds  
• Drawers that do not fully extend or retract
• Drawers detaching from the rail mechanism

This OEM LG rail is compatible with LG and Kenmore French door refrigerator models.

The Freezer Drawer Rail is an OEM component for LG French door refrigerators featuring bottom drawer designs. It provides smooth gliding support for the refrigerator's lower freezer storage compartment.

Common causes involve typical fatigue damage concentrating stresses at sensitive drawer guide interfaces.

Symptoms include:

• Drawer difficult to fully extend or retract
• Noises or binding during operation 
• Reduced storage organization from impaired drawer support

This OEM LG part can also be used on Kenmore/Sears appliances.

This ice maker drive gear engages the ice maker's motor to rotate the ejector and harvest ice, restoring proper ice release and ejection. Ideal for common ice-maker failures where the tray doesn't cycle. What it does:

• Transfers motor torque to the ice ejector, allowing the ice maker to harvest and eject cubes
• Commonly used when the ice maker stops cycling or fails to eject ice
• Can reduce grinding or clicking noises if the original gear is stripped or worn
• Works with the ice maker's harvest and fill sequence to maintain normal operation

• Power off and unplug the refrigerator before beginning service
• Remove the ice maker assembly per manufacturer instructions to access the gear
• Inspect mating gears and motor shaft for wear; replace any damaged parts to prevent repeat failure

This supporter hinge is the OEM-style hinge support that helps secure and align the appliance door, restoring stable door movement and proper sealing. Built to match the original hinge geometry for reliable fit. What it does:

• Supports the door at the hinge mounting point to keep door alignment stable
• Helps prevent sagging or uneven door gaps that can cause poor sealing
• Restores smooth opening and closing when worn or damaged hinge support is the cause
• Works as the hinge mounting support component shown in OEM parts diagrams

• One supporter hinge

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Follow the appliance's service manual for disassembly order and hinge removal/installation steps
• Use common hand tools (screwdriver, socket) and keep fasteners organized for reassembly
• Check adjacent hinge components and mounting hardware

This center hinge assembly replaces the factory center hinge that supports and aligns the refrigerator doors, restoring proper door movement and a tight seal for efficient cooling. It's a direct-fit mechanical hinge used where the upper and lower doors meet. What it does:

• Supports the weight of the upper/lower doors and maintains proper door alignment
• Lets the door pivot smoothly to open and close without binding
• Helps the door seal correctly to prevent warm air leaks and frost buildup
• Stops sagging or uneven door gaps that cause rubbing or poor closure

• One center hinge assembly

• Disconnect power to the appliance before starting work; if the unit has a water line, shut off the water supply as needed
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use basic hand tools; follow the manufacturer service instructions for torque and fastener sequence

This center hinge assembly secures and guides a refrigerator door, restoring proper door alignment and smooth opening/closing. Replacing a worn or damaged center hinge helps stop sagging doors and improves seal integrity for reliable cooling. What it does:

• Supports the center of a refrigerator door and keeps it aligned on the cabinet frame
• Guides door movement to ensure smooth opening and closing
• Restores proper door fit to help maintain an even door seal
• Addresses symptoms such as door sagging, misalignment, scraping or grinding noises from the hinge

• Disconnect power to the appliance before starting any repair.
• Doors are heavy; support the door and use a second person or proper support when removing or installing hinges.
• Keep track of fasteners and hinge shims or spacers; reinstall in the same order and orientation.

This turntable roller ring sits under the glass tray and allows it to rotate smoothly for even heating. Replace a worn, warped, or broken ring to restore stable rotation and consistent cooking performance.

• Supports the glass turntable and rides on built-in rollers for smooth, quiet movement
• Keeps the tray level and centered to promote even heating
• Common symptoms: tray not turning, uneven cooking, scraping/grinding noises, or a wobbly/slipping turntable
• Restores proper interaction between the turntable, drive coupling, and motor

• Unplug the microwave or switch off the breaker before servicing
• Remove the glass tray; lift out the old ring and clean the track
• Place the new ring with the rollers facing down on the track; reseat the tray on the center drive coupling
• Test rotation with a microwave-safe cup of water

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This tension spring provides the restoring force for a moving component in select LG appliances, helping doors or internal mechanisms return to their resting position and maintain correct alignment. It's a small mechanical part that restores motion reliably when functioning. What it does

• Supplies tension to return or hold a moving part (door, hinge or internal linkage) in its intended position
• Restores smooth, consistent motion and helps prevent slamming or sagging caused by worn springs
• Common symptom: door or component does not return, feels loose, or has uneven movement
• Works as a direct-fit service part when the original spring has stretched, broken, or lost tension

• One spring (quantity: 1)

• Inspect the matching mounting points and hardware before installing; replace any damaged clips or pins
• Use care when removing/installing under tension; wear eye protection and follow safe-handling practices
• Only install the part in appliances that list the same part number/location; do not force mismatched parts

This replacement lever spring restores tension to a lever-style mechanism so the lever returns and operates reliably. Use it when a worn spring causes the lever to stick, slip, or fail to engage properly. What it does

• Replaces the worn or weakened spring in a lever assembly to restore proper return tension
• Helps prevent the lever from sticking, slipping, or failing to stay engaged
• Restores consistent mechanical movement for reliable operation
• Reduces intermittent or flaky lever behavior caused by a damaged spring

• Disconnect power to the appliance before starting any repair
• Inspect the lever assembly and mounting points; replace only the spring explicitly listed
• Use appropriate hand tools and pliers; avoid overstretching the spring during installation

This lever spring is a small replacement tension spring that restores proper return and engagement for a lever assembly. It helps maintain reliable lever movement and secure latching where a worn or broken spring causes play or non-return. What it does:

• Provides return tension for a lever or latch assembly so the lever snaps back into place
• Helps maintain proper engagement of latch/actuator mechanisms
• Common remedy for a loose, sagging, or non-returning lever
• Works as a direct-fit replacement when the original lever spring is damaged or fatigued

• One replacement lever spring

• Disconnect power and/or unplug the appliance before starting any disassembly
• Handle small springs carefully; keep track of orientation and any retaining clips during removal
• Installation may require partial disassembly of the trim or latch assembly

This lever holder is the replacement mounting bracket that secures the door lever so the microwave door operates smoothly and reliably. It restores proper lever alignment to help the door latch and release as intended. What it does:

• Secures the door lever assembly so the door can latch and release properly
• Keeps the lever aligned to prevent binding, sticking, or loose movement
• Helps restore normal door operation and user access to the oven cavity
• Common symptom: door feels loose, lever moves freely, or door will not latch

• Disconnect power before beginning any repair to avoid shock or injury
• Remove the outer cabinet or door trim only as needed to access the lever area
• Handle door components and glass carefully to avoid damage or injury

A replacement display cover assembly that protects and shields the control panel lens while restoring a clean, readable appearance. Replaces a cracked, scratched, or discolored cover to improve display visibility and protect underlying electronics. What it does:

• Protects the control panel display and buttons from dirt, spills, and wear
• Restores a clear viewing surface when the original cover is scratched, cloudy, or damaged
• Helps prevent moisture and debris from reaching the display electronics
• Maintains the appliance's finished look and user interface usability

• Disconnect power to the appliance before beginning any work
• Removal typically requires opening or removing the control panel; use appropriate hand tools and keep fasteners organized
• Handle the cover by the edges to avoid fingerprints or scratches during installation

This electrical wire-harness connector links wiring to the appliance's control or component, restoring a secure electrical connection and helping eliminate intermittent power, no-start, or erratic component behavior. What it does:

• Provides a secure mating point between the wiring harness and an appliance control, motor, or sensor
• Restores reliable electrical contact when the original connector is damaged, corroded, or loose
• Can stop symptoms like intermittent operation, loss of power to a component, arcing, or related error codes
• Designed to match the OEM shape and terminal arrangement for a direct replacement

• One connector

• Disconnect power (unplug or switch off circuit breaker) before servicing to avoid shock
• Verify the connector matches the original by comparing terminal count, shape, and wire colors before installation
• Inspect mating terminals and wiring for damage; repair or replace harness wires if needed

This cover panel replaces a damaged or missing exterior trim piece to restore the appliance's appearance and protect internal components from dust and debris. It fits where the original cover was mounted and keeps wiring and parts shielded. What it does

• Covers and protects internal components from dirt and accidental contact
• Restores the appliance's exterior finish for a clean, finished look
• Helps reduce rattles by securing loose openings or edges
• Matches the original mounting locations for proper fit and alignment

• Disconnect power (unplug appliance or switch off breaker) before starting work.
• Removal/install typically requires basic tools (screwdriver or nut driver); keep original fasteners unless replacements are provided.
• Handle with care to avoid scratching the finish or breaking mounting tabs; avoid forcing clips.

The Link is an OEM part for LG refrigerators. It serves as an integral connector between the refrigerator door and cabinet, facilitating smooth opening and closing of the door. With durable construction and precise engineering, the link is designed to withstand the rigorous motion of hundreds of door openings without compromising functionality. 

Symptoms of a bad link include:

• Doors that do not close or seal properly 
• Excessive noise or vibration from the door area
• Damage, bending, or breakage of the connecting pieces
• Misalignment impairing proper door operation

Causes can stem from normal wear and tear over many years of use. Replacing a faulty link restores the refrigerator door's designed motion for convenient access to the interior.

This OEM LG part fits seamlessly while extending the product's useful life. This part is also compatible with Kenmore models featuring LG's refrigerator link assembly design.

This damper assembly controls airflow between refrigerator compartments to help maintain set temperatures and even cooling. Replaces a failed or stuck damper to restore proper air distribution and temperature balance. What it does:

• Regulates airflow between compartments so cold air moves where needed
• Can stop stuck-open or stuck-closed airflow that causes uneven temperatures
• Often linked to symptoms like warm spots, inconsistent cooling, or temperature swings
• Help reduce excess frost or humidity issues caused by improper airflow

• Disconnect power to the appliance before starting any repair
• Access usually requires removing interior liners, shelves, or panels; follow the service manual
• Handle actuator and wiring carefully; avoid pinching wires when reinstalling

NOTE: This part also requires software update kit CJT30000002. DO NOT INSTALL WITHOUT UPDATING SOFTWARE. Call for more information.

This evaporator assembly is the sealed coil component that removes heat from the freezer section, helping maintain proper cold temperatures and consistent food preservation. It replaces a worn or damaged evaporator to restore effective cooling. What it does:

• Absorbs heat from inside the freezer compartment so the refrigerant can carry it away
• Supports proper airflow through the freezer evaporator compartment for consistent cooling
• Commonly used when the freezer is not reaching temperature or shows frost/freeze buildup on the evaporator area
• Works with the appliance's defrost system and refrigeration components to maintain correct operation

• Disconnect power before servicing; handle components carefully to avoid sharp fin injury
• Inspect surrounding gaskets, insulation, and mounting hardware during replacement and replace as needed
• Test defrost and fan operation after installation to confirm proper system function

The Thermistor Assembly, PTC is an OEM part for LG refrigerators. Located within refrigerator compartments, the thermistor monitors interior temperatures sending signals to the control board. It contains a temperature-sensitive resistor to provide precise feedback on cooling needs. This feedback allows the refrigeration system to maintain consistent temperatures across all food storage areas. 

The causes of thermistor issues arise from normal component degradation, impacts, water damage, and manufacturing defects affecting sensor accuracy.

Symptoms of a bad Thermistor Assembly include:

• Fluctuating or inaccurate temperature readings  
• Compartments failing to maintain proper cooling levels
• Frost or condensation builds up inside
• Repeated Auto Defrost error messages

This genuine LG replacement preserves dependable monitoring for balanced refrigeration control. Keeping food fresher longer and suitable for Sears/Kenmore refrigerators with LG components.

The Overload Compressor is an OEM part for LG refrigerators. This part protects the refrigerator's compressor from overheating and potential damage by acting as a safety device. It works by monitoring the compressor's electrical current and temperature. If the compressor operates under conditions that could lead to overheating or overcurrent, the overload protector will cut off the power to the compressor, allowing it to cool down before potentially restarting.

Causes of damage to the Overload Compressor can include power surges, electrical faults within the refrigerator, or a malfunctioning compressor that requires more current than usual to operate. 

Symptoms of a bad Overload Compressor include:

• The refrigerator not cooling properly or not cooling at all
• The compressor failing to start, indicated by a clicking sound coming from the back of the refrigerator where the compressor is located.
• The refrigerator or freezer section warming up

This OEM LG part is also compatible with some Kenmore models.

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

This fan guide directs airflow from the blower/fan assembly to improve cooling and airflow routing in the appliance. Replaces a cracked or missing guide to restore proper airflow and reduce noise from misdirected air. What it does:

• Channels air from the fan/blower to the correct vents or components
• Helps maintain even cooling and prevents hot spots near electronics or food compartments
• Reduces vibration-related rattles by securing the fan's airflow path
• Common symptom: airflow is weak, noisy, or misdirected when the guide is damaged or missing

• One fan guide

• High-level replacement — remove access panels and unplug appliance before starting
• Confirm correct orientation and secure mounting tabs/screws; avoid forcing plastic clips
• Use gloves to protect hands from sharp sheet metal edges inside the cabinet
• If airflow or noise persists after installation, inspect fan/blower and motor assembly for damage

This drip tray catches and channels water runoff inside the appliance to help prevent pooling and minor leaks. It's a direct-fit replacement listed by the manufacturer and sold as the single tray used in the unit. What it does

• Collects condensate or defrost water and directs it to the drain area to prevent pooling.
• Helps stop water from dripping onto lower drawers, shelves or the floor.
• Commonly replaces a cracked, warped or missing tray that causes visible leaks or water buildup.
• Fits into the appliance's lower compartment where the original tray sat.

• Unplug the appliance or disconnect power before servicing.
• Remove any obstructing drawers or shelves to access the tray location; handle glass shelves carefully.
• Lift out the old tray and set the new tray into the same position; no special tools typically required.

This drain tray assembly collects and directs moisture and condensate to the drain system, helping prevent leaks and pooling under the appliance. Designed to fit the appliance's drain path and restore proper drainage. What it does:

• Captures condensate and channel water toward the drain to reduce standing moisture.
• Helps prevent water from pooling under components that could cause corrosion or odors.
• Restores proper drain routing after a damaged or cracked tray is removed.
• Works with existing hoses and clips to maintain normal drainage performance.

• Disconnect power and water before beginning repair.
• Remove access panels or components as needed to reach the drain tray; keep fasteners organized.
• Inspect surrounding seals, hoses, and clips and replace any worn parts to ensure a watertight fit.
• Reassemble panels and test the appliance for proper drainage and leaks before returning to service.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

The Drier Assembly is an OEM part for LG refrigerators. This part removes moisture and contaminants from the refrigerant, ensuring the system operates efficiently and effectively. The drier assembly helps maintain the proper function of the compressor and other cooling components, contributing to the longevity and performance of the refrigerator.

Causes of a bad drier assembly can include clogs from debris, wear and tear over time, or contamination from moisture or refrigerant leaks.  

Symptoms of a bad drier assembly include:

• The refrigerator not cooling properly
• Frost or ice buildup on the evaporator coils
• Increased noise from the compressor
• Reduced efficiency and higher energy consumption
• You should replace the drier assembly if it becomes faulty or damaged.

This OEM LG part is also compatible with select Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This damper controls airflow between compartments to help maintain proper temperatures and consistent cooling. It replaces a worn or broken damper to restore normal airflow and temperature balance inside the appliance. What it does:

• Regulates air flow between compartments so the refrigerator can maintain set temperatures
• Helps reduce uneven cooling and temperature swings caused by a stuck or broken damper
• Works as part of the appliance's air distribution system to route cooled air where needed
• Common symptom: compartment temperature too warm or inconsistent airflow noise from the damper area

• One damper assembly

• High-level replacement; access usually requires removing interior panels or duct covers
• Disconnect power before any repair to avoid shock or injury
• Handle with care to avoid bending or damaging mounting tabs and linkage

The Defrost Control Assembly is an OEM part for LG refrigerators. It is designed to regulate the defrost cycle, ensuring that frost buildup on the evaporator coils is periodically melted away. This helps maintain efficient cooling performance and prevents excessive ice accumulation, which can hinder the refrigerator's functionality.

You should replace the defrost control assembly if it becomes faulty. Causes of a bad defrost control assembly can include electrical failures, regular wear and tear, or damage from power surges. A malfunctioning defrost control can lead to issues such as inadequate defrosting, which results in excessive frost buildup and affects the cooling efficiency of the refrigerator.

Symptoms of a bad defrost control assembly include:

• Frost buildup on the evaporator coils
• The refrigerator not cooling properly
• The defrost cycle not initiating or running too frequently
• Increased energy consumption due to the refrigerator working harder to maintain temperature

This OEM LG part is also compatible with Sears/Kenmore models.

The Refrigerator Control Assembly is an OEM part for LG refrigerators. This component is crucial for managing and regulating the refrigerator's cooling and defrosting cycles. It ensures the proper operation of the refrigerator by controlling the temperature and defrost settings.

Causes of a bad control assembly can include electrical surges, wear and tear over time, or moisture damage. These factors can lead to malfunctioning controls or inconsistent temperature regulation within the refrigerator.

Symptoms of a bad control assembly include:

• Refrigerator not cooling properly
• Unusual noises from the control panel
• Inconsistent temperature readings
• Refrigerator not defrosting automatically

This OEM LG part is also compatible with Sears/Kenmore.

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

The Evaporator Fan Motor is an OEM part for LG refrigerators. This motor circulates air within the refrigerator, ensuring even cooling and maintaining the desired temperature throughout the appliance.

Common causes of failure include wear and tear over time, electrical issues such as power surges, or physical damage from mishandling or impact.

Symptoms of a bad evaporator fan motor include:

• Unusual noises from the freezer or refrigerator compartments
• Inconsistent or insufficient cooling
• The motor not running or running sporadically
• Ice buildup in the freezer due to poor air circulation

This OEM LG part is also compatible with some Kenmore models.

Replacement lamp cover that protects and diffuses an appliance's interior light, restoring even illumination and shielding the bulb from spills and contact. Restores proper light output and appearance after a cracked or missing lens. What it does:

• Protects the interior light bulb from food splatter, grease, and accidental contact.
• Diffuses and evens interior illumination to reduce hot spots and glare.
• Replaces cracked, yellowed, or missing lenses that can cause dim, flickering, or exposed-bulb issues.
• Matches the original lamp housing shape and secures with the appliance's existing clips or screws.

• Always disconnect power (unplug appliance or switch off circuit) and allow the bulb to cool before beginning.
• Remove any retaining screws or clips carefully; handle the cover gently to avoid cracking.
• Seat the cover securely in the lamp housing and reinstall original hardware—do not overtighten screws.
• After installation, restore power and verify the light operates and the cover is properly seated.

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Front Evaporator Motor Grommet is an OEM part for LG refrigerators. This grommet cushions and secures the evaporator motor, reducing vibrations and noise during operation to ensure efficient cooling.

Causes of a bad grommet can include prolonged use leading to material fatigue, exposure to extreme temperatures, or physical damage from accidental impacts. A damaged grommet can result in increased noise and potential misalignment of the evaporator motor.

Symptoms of a bad evaporator motor grommet include:

• Increased noise from the refrigerator
• Vibrations or rattling sounds
• Poor cooling performance
• The evaporator motor becoming loose

This OEM LG part is also compatible with Sears/Kenmore.

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

The Magnet Switch is an OEM part for LG refrigerators. It plays an important role in monitoring the position of the refrigerator door. 

The magnet switch works together with a magnet installed in the door gasket to detect when the door is opened or closed. It communicates this information to the control board which uses it to manage temperatures and fan speeds accordingly. 

Causes of a bad magnet switch can include wear and tear over time, physical damage, or failure of internal components. 

Symptoms of a bad magnet switch include:

• Improper cooling and freezing performances 
• Inability to detect when the door is opened
• Erratic temperature fluctuations
• Errors codes relating to door sensors

This genuine OEM LG magnet switch restores the door monitoring functions of your refrigerator. It is also compatible with Sears/Kenmore refrigerator models.

The Door Bracket is an OEM part for LG refrigerators. This bracket supports the refrigerator door by providing stability and ensuring proper alignment during opening and closing. It plays a crucial role in maintaining the door’s secure fit, which is essential for maintaining the internal temperature and efficiency of the appliance.

Common causes of a bad door bracket include wear and tear from frequent use, impact damage, or corrosion due to moisture.

Symptoms of a bad door bracket include:

• The refrigerator door not closing properly
• The door sagging or being misaligned
• Unusual noises when opening or closing the door
• Gaps in the door seal leading to temperature inconsistencies

This OEM LG part is also compatible with Sears/Kenmore.

The motor bracket assembly secures the motor inside your appliance, keeping it aligned and stable. Replacing a damaged bracket helps reduce vibration-related noise and prevents the motor from shifting or rubbing during operation.

• Securely supports and positions the motor within its housing
• Maintains proper alignment and clearance to prevent rubbing or scraping
• Helps reduce vibration and rattling noises from a loose or broken mount
• Replaces cracked, warped, or broken brackets that allow the motor to move

• Disconnect power to the appliance before servicing; wear cut-resistant gloves.
• Remove the necessary cover/panel to access the motor area.
• Transfer the motor and any cushions/grommets and screws from the old bracket to the new one.
• Ensure moving parts rotate freely and wiring is secured before reassembly.

Restore proper defrost performance with this sheath heater. It warms the evaporator during the automatic defrost cycle to melt accumulated frost, keeping air passages clear so your refrigerator and freezer maintain stable, efficient temperatures.

• Heats the evaporator coil during defrost to melt frost and ice
• Helps maintain airflow and consistent compartment temperatures
• Supports efficient cooling and proper defrost drainage
• Typical failure signs: heavy frost on the evaporator cover, warm fridge/freezer, or fan noise from ice contact

• Disconnect power to the appliance before servicing
• Remove shelves/drawers and the evaporator cover to access the heater; defrost any ice buildup first
• Handle the element carefully to avoid damaging evaporator fins; transfer any reusable clips/shields from the original
• Ensure all connectors are fully seated before reassembly, then restore power and verify defrost operation

The sheath heater is the electric resistance element that produces heat inside the appliance. Replacing a failed element restores reliable heating so the unit reaches temperature and completes its cook or defrost cycles as designed.

• Generates heat when energized to support baking/broiling or defrost functions
• Helps the appliance reach and maintain target temperature for consistent performance
• Typical failure signs: no or weak heat, long preheat/heat recovery, visible cracks/blisters on the element, or breaker tripping when the element energizes
• In defrost use-cases: heavy frost buildup on the evaporator and poor cooling due to iced coils

• Disconnect power at the breaker or unplug the unit; allow all surfaces to cool completely
• Handle the element carefully—do not bend the sheath; wear cut-resistant gloves
• Note wire positions, transfer any brackets/clips from the old part, and make tight, clean connections
• Inspect nearby high-heat wiring and terminals for damage and replace as needed; test operation before fully closing panels

This LED assembly restores backlight illumination for compatible LG displays, improving screen brightness and uniformity so images look clearer and easier to see. It replaces a worn or failed backlight strip. What it does:

• Provides the backlight illumination that lights the LCD panel
• Restores overall brightness and reduces dark or dim areas
• Can stop flickering or intermittent light if LEDs are failing
• Helps eliminate uneven lighting or bright/dark bands across the screen

• One LED assembly (single backlight strip) as shown

• Disconnect power and allow capacitors to discharge before starting
• Handle the LED strip and circuit board by the edges; avoid touching LED surfaces and PCB traces
• Keep track of screws and clips; test the display before fully reassembling

This LED light assembly illuminates the refrigerator interior when the door opens, delivering bright, efficient lighting so you can easily see items. Replace a failed module to restore proper visibility inside your fridge.

• Provides interior illumination for the fresh food or freezer compartment
• Turns on and off with the door switch
• Helps you quickly find items and check food condition
• Common symptoms: no light when doors open, flickering/strobing, dim or intermittent lighting

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, release retaining tabs, and unplug the wire harness to remove the old module
• Connect the new assembly, align tabs, and snap/secure it into place; reinstall the cover
• Restore power and verify operation; the door switch activates the light

The Capacitor is an OEM part for LG refrigerators. It plays a vital role in the electrical system, providing the necessary power boost to start the compressor and maintain its operation. This component ensures that the refrigerator runs efficiently by stabilizing voltage and improving overall performance.

Common causes of a bad capacitor include electrical surges, wear and tear over time, or exposure to excessive heat.

Symptoms of a bad capacitor include:

• The refrigerator not cooling properly
• The compressor not starting or running intermittently
• Unusual noises coming from the refrigerator
• The refrigerator cycling on and off frequently

This OEM LG part is also compatible with Sears/Kenmore models.

This SVC PCB power control board assembly replaces the refrigerator's onboard service/control module to restore proper power and control functions. It helps address control errors and loss of display or responsiveness after a board failure. What it does:

• Controls power distribution to diagnostic and user-interface circuits
• Enables onboard service/communication functions used during troubleshooting
• Works as the direct replacement for the refrigerator's SVC/service control PCB assembly

• Only install with power disconnected; disconnect the appliance from power before servicing
• Ground yourself and handle the board by edges to avoid ESD damage