Parts for Kenmore 796.31513211 (79631513211, 796 31513211): Other Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This tub cover assembly attaches to the outer tub of the washer, finishing the tub opening and helping keep water and suds contained. Replacing a damaged cover helps prevent leaks and unwanted splashing from the tub rim.

• Forms the protective rim at the top of the tub to reduce splashing and leaks
• Helps guide laundry away from the tub edge during agitation and spin
• Restores a secure, rattle-free fit when original tabs or the ring are cracked
• Common signs it's needed: visible cracks, broken tabs, warped ring, water splashing from the top rim

• Disconnect power; turn off water supply and move the washer for safe access
• Remove the top/lid or surrounding panels as required by the model
• Release retaining clips/screws and any attached guides/hoses from the old cover; transfer reusable parts
• Seat the new cover evenly and snap/secure all tabs before reassembly; run a short fill/spin to check for leaks

This holder assembly is a direct replacement mounting bracket that secures refrigerator internal components so they stay properly positioned and function reliably. Replaces a cracked or loose bracket to restore stable support and reduce rattling. What it does

• Secures internal components or assemblies to the cabinet to prevent shifting and vibration
• Restores proper alignment when a cracked or broken holder causes loose parts
• Helps stop rattling, knocking, or intermittent contact caused by a failed mount
• Works as a structural replacement—matches OEM fit and mounting points

• One holder assembly

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove nearby shelves, bins, or trim for access as needed; keep small fasteners organized
• Typically installs with basic hand tools; do not overtighten fasteners to avoid cracking
• If the part attaches to electrical components, verify connectors are secure before restoring power

The Pulsator Cap is an OEM part for LG washing machines. It is designed to secure the pulsator (or agitator) in place, ensuring proper movement of the wash plate during the wash cycle. This component helps in the effective distribution of water and detergent, promoting thorough cleaning of clothes.

You should replace this pulsator cap if it becomes damaged, lost, or worn out. Causes of a bad pulsator cap can include regular wear and tear, exposure to heavy loads, or damage from improper handling. A compromised cap can lead to inefficient washing and potential damage to the pulsator.

Symptoms of a bad Pulsator Cap include:

• The pulsator becoming loose or dislodged
• Unusual noises during the wash cycle
• Clothes not being cleaned properly
• The washer experiencing imbalance issues

This OEM LG part is also compatible with Sears/Kenmore models.

This top bracket secures the appliance's top panel and helps keep upper components properly aligned for stable operation. It provides a direct replacement for damaged or bent mounting brackets to restore panel fit and reduce noise. What it does:

• Holds the top/panel in place to prevent movement and misalignment
• Helps reduce rattling or vibration caused by a loose top panel
• Supports attached controls or components mounted near the top
• Restores proper gap and fit between the top panel and cabinet

• Disconnect power (unplug or shut off circuit) before starting any repair
• Typical installation requires removing the top panel and fastening bracket with standard screws; use appropriate hand tools
• Inspect surrounding fasteners and mounting points; replace any stripped screws or damaged clips

The Customized Screw is an OEM part for securing the wash plate in LG washing machines. This screw maintains the wash plate's position and stability during the washer's operation. The Customized Screw ensures the wash plate performs efficiently, contributing to the effectiveness of the washing process by enabling proper agitation and circulation of clothes.

Causes of a bad Customized Screw can include wear and tear over time, especially from the constant motion and stress during the wash cycles.  

Symptoms of a bad Customized Screw include:

• The wash plate becoming loose or detached
• Ineffective washing due to improper motion of the wash plate
• Unusual noises during the wash cycle indicating a loose component

This OEM LG part is also compatible with some Kenmore models.

Replace a damaged or stripped leveling foot with this leg assembly. It supports the appliance and adjusts for height so you can level it on uneven floors, restoring stability and helping reduce vibration, noise, and movement. What it does:

• Provides adjustable height to properly level the appliance
• Supports the cabinet/frame to keep all corners in firm contact with the floor
• Helps reduce rocking, walking, vibration, and rattling noises
• Fixes: appliance wobbles or is unstable; foot is cracked/missing; threads are stripped; cannot be leveled

• One leg assembly

• Disconnect power and, if applicable, turn off the water supply before servicing
• Carefully tilt or raise the appliance; protect the floor from scratches
• Unscrew the old leg; thread the new leg in by hand and adjust height to level
• Ensure all feet contact the floor firmly and the unit is stable before use

Replace a damaged or stripped leveling foot with this leg assembly. It supports the appliance and adjusts for height so you can level it on uneven floors, restoring stability and helping reduce vibration, noise, and movement. What it does:

• Provides adjustable height to properly level the appliance
• Supports the cabinet/frame to keep all corners in firm contact with the floor
• Helps reduce rocking, walking, vibration, and rattling noises
• Fixes: appliance wobbles or is unstable; foot is cracked/missing; threads are stripped; cannot be leveled

• One leg assembly

• Disconnect power and, if applicable, turn off the water supply before servicing
• Carefully tilt or raise the appliance; protect the floor from scratches
• Unscrew the old leg; thread the new leg in by hand and adjust height to level
• Ensure all feet contact the floor firmly and the unit is stable before use

This hardware washer sits beneath a screw or nut to spread load and help keep fasteners tight inside your appliance. Replacing a bent or missing washer restores a secure fit and can reduce vibration-related noise. What it does:

• Distributes clamping force to protect mounting surfaces
• Helps resist loosening from vibration and movement
• Restores proper alignment when a washer is damaged or missing
• Common symptoms: loose or wobbling parts, rattling noises, screws backing out

• 1 washer

• Disconnect power; if working on a washer, also turn off water supply
• Note the original hardware stack order and take photos for reference
• Place the washer between the fastener head or nut and the part being secured
• Tighten to manufacturer guidance; avoid overtightening to prevent damage

This replacement holder is a small mounting bracket used to secure components inside the appliance, restoring proper alignment and support so parts sit firmly and operate as intended. Ideal when a cracked or worn holder causes instability. What it does

• Secures internal components or assemblies to prevent movement or vibration
• Restores proper alignment when a damaged holder allows parts to sag or shift
• Helps reduce noise from loose or unsecured components
• Commonly replaced when the original holder is cracked, broken, or missing

• Turn off and unplug the appliance before beginning any repair.
• Inspect surrounding clips and fasteners; replace any damaged hardware for a secure fit.
• Use appropriate hand tools; avoid forcing parts to prevent further breakage.

This genuine hardware washer installs at the specific joint shown in your model's parts diagram. It spreads clamp force and keeps the connection aligned and secure to support smooth operation of the related component. What it does:

• Distributes fastener load and protects mating surfaces from damage
• Maintains proper spacing and alignment within the assembly
• Helps resist loosening from vibration over time
• Clues it may be needed or worn: loose/rattling parts, unusual vibration or noise, or visible wear at the fastener location; on some models, seepage at that joint

• 1 washer

• Disconnect power and turn off water supply before servicing
• Support the assembly, remove the fastener, and install the washer in the same orientation
• Tighten the fastener snugly without overtightening; replace any damaged bolts, nuts, or seals

This Main PCB Power Control Board Assembly is the appliance's central electronic control module, restoring control of functions and user-interface signals when the original board fails. Designed as a direct replacement assembly for compatible units. What it does:

• Manages power and logic for the appliance's control circuits and user interface.
• Can resolve symptoms such as blank or unresponsive displays, unresponsive controls, or erratic electronic behavior.
• Works with existing wiring harness and connectors when matched to the correct replacement board.

• Disconnect power to the appliance before beginning any repair to avoid shock or damage.
• Handle the PCB by its edges and avoid static discharge; use ESD protection if available.
• Remove access panels and label or photo connectors before unplugging; reconnect exactly as removed.

The balancer assembly mounts to the washer's basket/tub to counterbalance loads during spin. When worn or damaged, it can cause shaking, banging, or out-of-balance errors. Replacing it helps restore smoother, quieter spin performance.

• Stabilizes the basket/tub during acceleration and high-speed spin
• Helps reduce vibration, banging, and washer "walking"
• Can prevent spin cycles from slowing or stopping due to imbalance

• Disconnect power and allow moving parts to stop before servicing
• Access is typically at the top of the tub/basket under the tub ring; remove covers as needed
• Note orientation; seat the assembly evenly and ensure all tabs/fasteners are fully engaged
• After reassembly, run an empty spin test to verify smooth operation

This inner tub hub connects the washer's inner drum to the drive assembly, providing a secure rotational link so the drum can spin properly. Replacing a damaged hub restores drum stability and reduces noise or wobbling. What it does:

• Secures the inner tub to the drive shaft so the drum turns with the motor
• Prevents excessive movement, vibration, and scraping noises caused by a worn or broken hub
• Helps correct spin-related issues like uneven spinning or the drum not engaging
• Works with the tub assembly and other drive components to maintain proper drum alignment

• One inner tub hub

• Disconnect power and water supply, and fully drain the washer before starting
• Replacement generally requires removing the outer tub/inner tub assembly and transferring seals or gaskets as needed
• Use proper tools and follow OEM service instructions
• Inspect surrounding components (seals, bearings, suspension) and replace if worn to prevent repeat failure

The Drain Pump Assembly is an OEM replacement part for LG washing machines. As an important part of the washer drain system, it drives the pumping action removing water from the tub at the end of each cycle.

Causes of drain pump failure include normal wear from continuous operation over time, foreign debris potentially clogging the impeller cavity, or mineral/scale buildup inhibiting pump function.

Symptoms of a faulty drain pump can include:

• Washer fails to fully drain water at the end of cycles
• Excess water remains in the tub requiring manual emptying
• Abnormal grinding/knocking noises emit from below the tub

This OEM LG part is also compatible with some Sears/Kenmore model washing machines.

This spring-style hose clamp secures flexible hoses to fittings to help maintain a watertight connection and prevent leaks. A simple replacement when the original clamp is worn, bent, or no longer holds tension. What it does:

• Holds washer, drain, or water-supply hoses firmly on barbs and fittings
• Restores clamping tension to stop drips or slow leaks at hose connections
• Prevents hoses from slipping off under pressure or vibration
• Helps maintain proper fluid flow by ensuring a tight seal

• One hose clamp

• Disconnect power and shut off water supply before servicing plumbing connections
• Use pliers or the appropriate clamp tool to expand and position the clamp; release slowly to seat it
• Replace any damaged or corroded hoses or fittings for a reliable repair

The Suspension Rod Assembly is an OEM part for LG washing machines. This assembly includes multiple rods designed to support the washing machine drum and minimize vibrations during the wash and spin cycles. By stabilizing the drum, the suspension rods help ensure smooth and quiet operation, preventing excessive movement that could damage the appliance.

Causes of a bad suspension rod assembly can include wear and tear from regular use, imbalance due to overloading the washer, or physical damage from accidental impacts. When the suspension rods are compromised, the washing machine may become unstable and noisy.

Symptoms of a bad suspension rod assembly include:

• Excessive shaking or vibrating during wash cycles
• Loud banging or thumping noises
• The washing machine moving or "walking" during operation
• Uneven or incomplete washing due to an unstable drum

This OEM LG part is also compatible with Sears/Kenmore models.

The Drain Hose is an OEM part for LG washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle. The hose measures 67.5 inches in length.

Causes of a bad drain hose can include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM LG part is also compatible with Sears/Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Lid Switch and Lock Assembly is an OEM component specifically designed for LG washing machines. It contains both the switch that detects when the lid is closed, as well as the metal lock mechanisms that securely engage the lid during active cycles. This switch contains a 47-inch wire harness with 6-pin plugs.

Symptoms of a bad lid switch and lock assembly include:

• The washer not starting or agitating with the lid open
• Inability to fully close or lock the washer lid
• Error codes related to sensed lid position issues

Causes of failure involve wear of lock moving parts combined with mechanical and electrical degradation over thousands of uses. Continuous hinge motions and detergent/cleaner exposure take their toll.

This Lid switch is also compatible with Kenmore units reliant on LG parts.

The Tub to Pump Hose Assembly is an OEM part for LG washing machines. This hose connects the tub to the drain pump, allowing water to be efficiently drained from the washing machine during the spin and drain cycles.

Over time, the hose can become clogged, develop cracks, or experience wear due to constant water flow and agitation. Damage can also occur from accidental mishandling or impact, leading to leaks or improper drainage.

Symptoms of a bad Tub to Pump Hose Assembly include:

• Water leaking from the washing machine
• Slow or incomplete drainage
• Error codes related to drainage issues
• Excess water remaining in the tub after the cycle

This OEM LG part is also compatible with Sears/Kenmore.

This bracket assembly secures internal components to the appliance frame, restoring stable support and alignment for panels or assemblies. Replacing a damaged bracket helps stop rattling and prevents misalignment that can affect operation. What it does:

• Provides a secure mounting point for panels, control boards, or internal assemblies
• Restores proper alignment to reduce vibration, noise, or rubbing parts
• Prevents loose components that can cause intermittent contact or wear
• Re-establishes structural support after impact, corrosion, or bracket failure

• One bracket assembly

• Verify power is disconnected before starting any repair
• Inspect mounting screws and adjacent parts; replace any damaged fasteners
• Tighten to manufacturer torque where specified and confirm proper alignment

This bracket assembly secures and supports internal appliance components, restoring proper alignment and stability to parts that have shifted or come loose. It provides a direct replacement to maintain safe, reliable operation. What it does:

• Provides a sturdy mounting point to keep panels, modules, or assemblies properly positioned
• Helps eliminate rattling, misalignment, or loose component movement
• Restores intended structural support after impact or wear
• Works as a direct-fit replacement to return original fit and function

• One bracket assembly

• Disconnect power (and water, if applicable) before beginning any repair
• Use appropriate tools and keep fasteners for a secure fit; replace damaged screws as needed
• Inspect surrounding components and wiring for damage before reassembly

The Softener Cap is an OEM part for LG washing machines. It serves as the lid and housing for the internal water softener that prevents mineral deposits from building up. The softener cap funnels water to and from the softener compartment during various stages of the wash cycle.

Causes of a faulty softener cap can include cracked or degraded seals over extended usage, impact damage distorting fit, or harsh cleaners affecting plastics over time.

Symptoms of a bad softener cap include:

• Water leaks from around the softener area  
• The cap not closing or sealing properly 
• Mineral buildup occurring prematurely
• The softener not functioning as intended

This genuine LG replacement is compatible with Sears/Kenmore machines.

This softener dispenser cap replaces the worn or cracked cap that covers the fabric softener chamber, restoring proper containment and controlled release of liquid softener during the wash cycle. A simple, low-cost part that prevents leaks and keeps the dispenser functioning. What it does

• Covers and seals the fabric softener compartment so liquid stays in the dispenser until the rinse cycle.
• Helps prevent softener from leaking into the washer drum between cycles.
• Restores a secure fit when the original cap is cracked, warped, or missing.
• Resolves issues with softener dispensing at the wrong time or pooling in the dispenser.

• One softener dispenser cap (1 piece)

• Disconnect power to the washer before accessing internal parts and follow all safety precautions.
• Typically accessed by removing the dispenser drawer or top panel—refer to your washer's service instructions.
• Inspect surrounding dispenser components for damage and replace any worn parts to ensure a proper seal.
• No electrical connections; basic hand tools may be required.

This replacement nozzle assembly directs and focuses the spray or dispense flow inside the appliance for reliable cleaning and dispensing performance. It restores proper spray pattern and helps maintain even coverage where required. What it does:

• Directs water or dispense flow to the target area for effective cleaning or dispensing
• Restores consistent spray pattern to improve wash or rinse coverage
• Can resolve symptoms like weak or misdirected spray, uneven cleaning, or reduced dispensing performance
• Designed to fit into the OEM nozzle mounting and work with existing seals and connections

• Disconnect power and shut off water supply before servicing
• Replace only with the exact OEM-design nozzle assembly to ensure proper fit and function
• Inspect surrounding seals and clips during installation; replace if damaged

This clutch assembly is a genuine OEM replacement part sourced directly from the manufacturer and is intended for use in washing machines. The clutch assembly controls the movement of the internal tub and agitator during operation. Over time and with regular use, the clutch assembly may become worn and fail to work correctly. If the washing machine tub is not moving back and forth during the wash cycle or is not spinning during the spin cycle, the clutch is broken. If it is moving or spinning, but not efficiently or fast enough, the clutch is worn and beginning to fail. In both of these instances, the clutch assembly should be replaced. Excessively wet clothes at the end of the laundry cycle can also be indicative of a broken clutch.A screwdriver, socket set, putty knife, and impact wrench with a large 38mm socket are required to make this replacement. Ensure the power is disconnected and the machine is drained. While the tub is out of the machine, take time to clean the area of gunk and buildup. Wear gloves while working on the machine.This clutch assembly is made of durable metals and is individually sold. It is designed for use in washing machines by LG and Kenmore.

The Water Inlet Valve is an OEM replacement part specific to LG washing machines. It is an electronic solenoid valve located near the water supply inlet ports that controls the flow of water into the washer tub. The inlet valve precisely regulates water levels during different phases like filling, washing, rinsing, and spinning cycles.

Causes of a bad water inlet valve can include worn or faulty electronic components, mineral buildup obstructing valve movement, or damage to seals and diaphragms.

Symptoms of a bad water inlet valve include:

• Inability to properly fill the washer tub during cycles
• Water leaking or flooding from the valve area
• Erratic water temperature or varying fill levels between loads
• Cycles failing to advance due to inadequate or unregulated water flow

This OEM LG part is also compatible with Sears/Kenmore models.

The Hose Connector is an OEM part for LG washing machines. It controls the water flow during the wash and rinse cycles. This part is designed to facilitate a secure and leak-proof connection between different sections of the washing machine, such as the inlet valve and the tub, or the pump and the drain hose. Ensuring these connections are secure is vital for the efficient operation of the washing machine, preventing leaks and maintaining optimal water usage.

Causes of failure may involve cracks, splitting, or collapsed seals/gaskets, as well as excessive mineral or foreign deposits that can obstruct water flow.

Symptoms of a bad hose connector are:

• Slow or incomplete filling during wash cycles
• Water leaks at the supply valve or connector area
• Connector split, cracked or compromised fittings

This genuine LG replacement is also compatible with Kenmore washing machines.

This inlet hose channels household water into the appliance during the fill cycle. Replacing a cracked, brittle, or leaking hose restores a secure, leak-resistant path that helps prevent puddles and fill-related interruptions. What it does:

• Routes incoming water from the inlet valve into the appliance's internal water path
• Helps maintain a watertight connection when properly secured with clamps
• Typical failure signs: dripping or puddling under the unit, visible cracks/kinks/bulges, or lingering dampness
• A restricted or leaking hose can contribute to long fill times or incomplete cycles

• 1 inlet hose

• Disconnect power and turn off the water supply before servicing
• Place towels or a shallow pan to catch residual water
• Note the original routing and clamp locations; install the new hose the same way without twists or kinks
• Fully seat hose ends and secure clamps; restore water and run a brief fill to check for leaks

Detergent housing assembly that holds and routes detergent to the washer dispenser, helping ensure proper detergent flow and reducing leaks or dispenser jams. Fits into the dispenser area to replace cracked, warped, or damaged housing components. What it does:

• Houses and channels liquid or powdered detergent into the dispenser and wash chamber
• Restores proper detergent release when the original housing is cracked, broken, or warped
• Helps stop leaks and detergent buildup around the dispenser area
• Works with the dispenser drawer and related seals to maintain correct flow

• Disconnect power and turn off the water supply before starting service
• Use basic hand tools and follow the washer service manual or OEM diagram for disassembly/reassembly
• Inspect and replace any worn seals or gaskets at reassembly to prevent leaks

This washer motor stator assembly is the stationary windings of the direct-drive motor. Replacing a weak or shorted stator restores smooth drum tumbling and strong, consistent spin performance so wash cycles complete properly.

• Creates the rotating magnetic field that drives the rotor and spins the inner basket
• Works with the rotor to provide torque for wash/tumble and high-speed spin
• Common symptoms: drum won't spin or tumble, stops under load, or motor hums without turning
• Burnt odor or visible heat damage on windings can indicate stator failure

• Disconnect power and turn off water; access the motor from the rear panel
• Remove the rotor center bolt and slide off the rotor; strong magnets—handle carefully
• Unbolt and remove the stator; transfer/reconnect the motor position (Hall) sensor and harness if present
• Tighten fasteners evenly; verify drum rotates freely by hand before restoring power

The Water Level Pressure Switch is an OEM replacement part for LG washing machines. It is an essential component that monitors and detects the water level within the washing machine tub during the wash cycle.

Symptoms of a bad water level pressure switch:

• Washing machine not filling with water or not stopping when the desired water level is reached
• Excessive water intake, leading to overfilling and potential leaks
• Error codes or indicators related to water level issues
• Washing machine not advancing to the next cycle due to incorrect water level detection

Causes of a bad water level pressure switch can include mechanical failure, electrical malfunctions, or blockages or debris preventing accurate water level readings.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

The Motor Rotor Assembly is an OEM part for LG washing machines. This component is crucial for the washer's motor operation, as it works in conjunction with the stator to create the electromagnetic field that drives the drum. It ensures the drum rotates effectively during the wash and spin cycles, facilitating thorough cleaning and efficient water extraction.

Over time, the motor rotor assembly can wear out or become damaged due to regular use, exposure to water, or excessive loads. Causes of a bad motor rotor assembly include bearing failure, corrosion, physical damage, or electrical issues.

Symptoms of a bad motor rotor assembly include:

• The washer not spinning or agitating
• Unusual noises such as grinding or squealing during operation
• The drum not turning or rotating inconsistently
• Error codes related to motor issues

This OEM LG part is also compatible with Sears/Kenmore.

The Water Level Pressure Switch is an OEM replacement part for LG washing machines. It is an essential component that monitors and detects the water level within the washing machine tub during the wash cycle.

Symptoms of a bad water level pressure switch:

• Washing machine not filling with water or not stopping when the desired water level is reached
• Excessive water intake, leading to overfilling and potential leaks
• Error codes or indicators related to water level issues
• Washing machine not advancing to the next cycle due to incorrect water level detection

Causes of a bad water level pressure switch can include mechanical failure, electrical malfunctions, or blockages or debris preventing accurate water level readings.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

The Clutch Motor is an OEM part for LG washing machines. This motor engages the clutch mechanism, allowing the washer to switch between agitating and spinning cycles effectively.

Causes of a bad clutch motor can include wear and tear over time, electrical issues, or mechanical failure due to overloading or improper use.

Symptoms of a bad clutch motor include:

• The washer not agitating or spinning
• Unusual noises during the wash or spin cycles
• The drum not rotating properly
• The washer stopping mid-cycle

This OEM LG part is also compatible with Sears/Kenmore models.

This filter assembly is the appliance's line noise filter. It conditions incoming AC power and suppresses electrical interference to protect sensitive controls and help restore stable, reliable power when the original filter has failed. What it does:

• Suppresses EMI/RFI on the AC line to reduce electrical noise reaching the control system
• Helps stabilize power to boards, relays, and motors
• Common failure symptoms: no power, intermittent power, tripped breaker or blown line fuse, burning smell or visible scorching at the old filter
• Also known as a line filter, EMI filter, or noise filter

• 1 filter assembly

• Disconnect power to the appliance before servicing; capacitors in some products can retain a charge
• Note wire locations; transfer leads to identical terminals on the new filter and secure the ground connection
• Mount the assembly firmly in the original location to prevent vibration or wire strain
• After replacement, inspect related fuses and wiring if the old filter showed signs of overheating or surge damage

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

This is a small OEM washer used with the washer's internal mounting hardware to provide proper spacing and secure fasteners. It helps keep assemblies aligned and prevents hardware from loosening during operation. What it does:

• Acts as a spacer and load distributor for bolts or screws in the washer assembly
• Helps maintain proper alignment of panels or components
• Reduces wear between mating metal parts
• Can prevent fasteners from backing out due to vibration

• One washer as pictured

• Always unplug the appliance and shut off the water supply before servicing
• Access the mounting location per the service manual or parts diagram; replace only like-for-like
• Install with the correct orientation and hardware; do not overtighten fasteners
• If other fasteners or parts are corroded or worn, replace them at the same time

Kit is no longer available. Order MCJ61861201 and ACP72929002 separately.

A replacement clutch housing assembly that secures the clutch coupling to the washer drive—restores proper drive engagement and helps eliminate slipping, grinding, or failure to spin. Designed as a direct-fit service part for affected LG washers. What it does

• Houses and supports the clutch coupling that links the drive to the transmission.
• Restores reliable transfer of drive force so the tub can agitate and spin.
• Helps stop symptoms like slipping between cycles, unusual grinding or vibration, and failure to spin.
• Replaces worn, cracked, or damaged housings that can cause poor clutch engagement.

• One clutch housing assembly

• Disconnect power and water supply before beginning any repair.
• Access typically requires opening the washer cabinet or back panel; follow your model's service manual.
• Inspect related clutch and transmission components while accessible.

This thermistor assembly monitors water temperature inside the washer tub and relays a precise signal to the control board. Replacing a failed sensor restores accurate temperature sensing and helps prevent cycle errors and performance issues. What it does:

• Measures wash water temperature and sends the signal to the electronic control
• Enables the control to adjust cycle operation based on temperature feedback
• Common failure signs: tE/TE error codes on some models, incorrect temperatures, long cycles, or cycles that won't advance
• Intermittent faults may cause sporadic errors or inconsistent performance

• 1 thermistor assembly

• Disconnect power and shut off water before servicing
• Access location varies by model; the sensor is typically mounted in the outer tub or heater housing
• Unplug the harness, pull the old sensor straight out; seat the new sensor fully and reconnect the harness
• Route wiring away from moving parts; restore power and run a test cycle, checking for proper operation and any leaks around the sensor port

The Dispenser Assembly is an OEM part for LG washing machines. This part dispenses the appropriate amounts of detergent, fabric softener, or other laundry additives at the right time during the wash cycle.

Causes of a bad Dispenser Assembly can include clogging or buildup of residue, damage to the dispensing mechanisms or components, or issues with the electronic controls that regulate the dispensing process.

Symptoms of a bad washer Dispenser Assembly include:

• Improper dispensing of detergent or fabric softener
• Leaks or drips from the dispenser area
• The dispenser drawer not opening or closing properly
• Failure of the dispenser to dispense at the correct time during the cycle

This OEM LG part is also compatible with some Kenmore models.

This clamp assembly secures a hose or tubing connection to maintain a watertight seal and reduce vibration. Replacing a worn or damaged clamp helps stop leaks and prevents hoses from slipping loose during operation. What it does:

• Holds a hose or tube firmly in place to maintain proper sealing at the connection point.
• Prevents leaks caused by loose, cracked or corroded clamps.
• Reduces vibration and rattling from unsecured hoses.
• Common symptom: visible leaking, water pooling, or a loose hose connection.

• Disconnect power and shut off water supply before starting any repair.
• Use the correct pliers or screwdriver for the clamp type; avoid damaging the hose.
• Inspect the mating hose and seal; replace any cracked or hardened hoses before reinstalling.
• Do not overtighten—tighten just enough to secure the hose without cutting or deforming it.

This cover cap is a small plastic trim piece that snaps into place to protect and finish an appliance opening or fastener, restoring a clean, finished appearance and keeping dirt out of the recess. What it does:

• Covers exposed fasteners or openings to improve appearance and prevent debris buildup
• Helps protect internal components from dust and small particles
• Restores a worn or missing trim piece for a finished look
• Fits into a corresponding recess and secures by snapping into place

• Installation is generally push-fit; align the cap with the opening and press until it snaps into place
• Use a plastic pry tool if removal is needed to avoid scratching surrounding surfaces
• Disconnect power to the appliance before removing panels or working near electrical components
• Only replace parts that match your appliance's OEM specifications

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.