Kenmore Washer Dryer Combo 110.C92962200 (110C92962200, 110 C92962200) Parts

The Terminal Block Screw Kit is an OEM replacement part for Whirlpool dryers. It is an assembly of screws used to securely fasten electrical terminal blocks within the dryer's control panel. Includes 3 screws and 3 nuts. Screw kit for dryer cord connector.

Over time, terminal block screws can become loose, corroded, or damaged due to regular use or electrical issues. If the terminal block screws are compromised, it can lead to electrical problems or even pose a safety hazard.

Symptoms of a faulty terminal block screw kit include:

• Intermittent power or failure of heating/fan elements to engage  
• Repeated blowing of internal fuses or tripping of circuit breakers
• Hot terminal connections detected during operation
• Arc flashes, sparks, or smoke seen around the control panel area

This genuine Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

Includes screws and wire connectors. For the complete terminal block kit use 279320.

The Washer Lid Screw is an OEM part for Whirlpool washing machines. This 6-32 x .340 screw secures the washer lid to the hinge assembly, ensuring the lid opens and closes smoothly and stays securely in place during operation.

Causes of a bad washer lid screw can include wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or mishandling. A compromised screw can lead to issues with the lid's stability and functionality.

Symptoms of a bad washer lid screw include:

• The washer lid feeling loose or wobbling
• Difficulty in opening or closing the lid
• Visible rust or corrosion on the screw
• The lid not staying securely in place

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 48 inches long. Clamp included. For 21 inch extension use 285702.

This U-type nut clips over a sheet-metal edge to create a durable threaded anchor for a screw. It helps secure panels, trim, and brackets so fasteners hold tight and components stay aligned and rattle-free. What it does:

• Clips onto thin sheet metal to provide captive threads where a standard nut cannot be used
• Holds screws securely to fasten panels, trim pieces, or mounting brackets
• Addresses issues like loose panels, missing/broken clips, or screws that will not tighten
• Helps reduce vibration and rattling from unsecured components

• 1 U-type nut

• Disconnect power and shut off gas/water before servicing
• Position the U-nut over the panel edge with the threaded side aligned to the hole
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged or corroded hardware to ensure a secure hold

The Balance Ring is an OEM part for Whirlpool washing machines. This part maintains the stability of the washer drum during the spin cycle. It contains liquid that helps balance the load, minimizing vibrations and noise while ensuring smooth operation.

Causes of a bad balance ring can include general wear and tear, exposure to heavy or unbalanced loads, or physical damage.

Symptoms of a bad balance ring include:

• Excessive shaking or vibrating during the spin cycle
• Loud banging noises
• Washer moving or walking during operation
• Uneven or off-balance loads

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Brake Shoe is an OEM part for Whirlpool washing machines. This part stops the spinning tub during the spin cycle, allowing the washer to transition smoothly to the next phase of the cycle.

Causes of a bad brake shoe can include regular wear and tear, excessive friction from heavy loads, or breakage due to mishandling.  

Symptoms of a bad brake shoe include:

• The washing machine not stopping the spin cycle promptly
• Loud squeaking or grinding noises during or after the spin cycle
• The tub continuing to spin when the lid is opened
• The washer shaking or vibrating excessively during the spin cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This gasket fits between the dishwasher's transition duct and its cover plate. It creates a tight barrier that helps keep wash water and steam contained, protecting the door cavity from moisture intrusion.

• Seals the joint between the transition duct and cover plate in the inner door vent path
• Helps prevent water or steam leakage from the vent area
• Replace if the seal is torn, deformed, brittle, missing, or leaking around the vent

• Disconnect power and turn off the water supply before servicing
• Remove the outer door panel to access the transition duct and cover plate
• Note the seal's orientation, remove the old gasket, and clean mating surfaces
• Seat the new seal evenly and reassemble; test a short cycle to check for leaks

The Capacitor is an OEM part for Whirlpool washers that starts the motor by storing electrical energy and releasing it when the washer begins its cycle. This part ensures the washer operates smoothly from the moment it starts, providing the necessary jolt to the motor that enables it to begin its various functions, including spinning and agitating. 

Causes of a bad capacitor can vary. Electrical surges can harm its internal components, while wear and tear over time may result in a reduced capacity to hold a charge.

Symptoms of a failing Capacitor include:

• The washer failing to start.
• A humming noise when the washer is supposed to begin its cycle 
• The washer starting but then quickly shutting down due to insufficient power to the motor.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Broken Belt Switch Kit is an OEM replacement part for Whirlpool dryers. It is an assembly that includes a microswitch and bracket installed to monitor the dryer drum belt status. The broken belt switch plays an important safety role by automatically stopping the dryer if it detects the drum belt breaking or slipping off the motor pulley during a cycle. The kit includes a switch, actuator lever, screws, and wire terminals.

Causes of a bad broken belt switch can include wear and tear over time, electrical malfunctions, or physical damage from a broken belt or other internal issues. Ensuring the switch is functioning correctly is crucial for the safe and efficient operation of the dryer.

Symptoms of a broken or failing switch include: 

• The dryer failing to shut off if the belt breaks during operation
• Inability to diagnose belt issues through error code displays  
• Intermittent stopping or variance in belt tension detection

This genuine Whirlpool switch replacement is also compatible with Kenmore, Maytag, Jenn-Air, and KitchenAid dryer models.

The Thermal Cutoff is an OEM replacement part for Whirlpool dryers. This cutoff component plays a crucial role in starting and stopping power to the dryer during operation. It does so through a sensitive thermal limiter that responds to temperature changes inside the dryer drum. 

Causes of a bad cutoff can include damage or wear to the thermal limiter over time, loosening of internal wiring connections, or issues with the cutoff's electronic components. 

Symptoms of a bad thermal cutoff include: 

• The dryer not turning on at all 
• The dryer fails to turn off after a full cycle
• Fluctuations in heat output during drying
• Buzzing or clicking noises coming from the cutoff area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This small hardware washer sits under a fastener in the specified assembly to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep components tight, aligned, and operating smoothly.

• Distributes clamping force to prevent fastener pull-through and damage
• Maintains correct spacing/stack-up in the original assembly
• Helps reduce loosening, vibration, and premature wear at the joint
• Typical signs of trouble include rattling, looseness, or misalignment at the connection point

• Disconnect power (and turn off water supply if accessing a wet area)
• Use your model's parts diagram to locate and install the washer
• Replace one-for-one; reinstall any spacers or clips in the same stack sequence
• Tighten fasteners to manufacturer guidance—do not overtighten

These lid bumpers are sold individually.

This idler pulley assembly keeps the drive belt properly tensioned and aligned so your appliance runs smoothly and quietly. Replacing a worn or seized idler restores reliable belt drive and helps prevent slippage, noise, and no-drive issues.

• Maintains spring-loaded tension on the drive belt
• Spins freely to reduce friction and belt wear
• Helps route and align the belt between the motor and drum/basket
• Typical symptoms of a failing idler: squealing/chirping, belt fraying or coming off, intermittent or no tumble/spin, burning rubber smell

• Disconnect power; for gas units, also shut off the gas supply.
• Relieve belt tension, swap the assembly, and route the belt per your unit's diagram.
• Rotate the drum/basket by hand to check alignment.
• Wear cut-resistant gloves and use caution around sharp edges and spring tension.

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.