Appliance Parts

• Spins slowly
• Burning smell
• Pumps but will not spin
• Noisy

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

Two weeks ago, my dishwasher would not run. It would beep three times when you pushed the start button: the same signal it gives when the door is open. I used the troubleshooting steps I found at applianceblog.com to do a hard reset. (Hold START and WASH TEMP for five seconds, close the door, and wait 3 minutes) After that, it worked for about one week. When it started having the same issue again, the hard reset did not work. I lowered the control board and could see that there were no lights.... Read more

• Noisy
• Door won't close
• Door latch failure

I finally decided to repair my dishwasher because the door would free fall to the floor possibly breaking the hinges. Also the top shelf was rolling out on its own every time the door was opened. I first pulled the dishwasher out of the enclosure and found that the drain hose was directly under the pump area throwing the unit completely out of level. Also the inadequate plastic and rope counterbalance on the left side was completely broken where the rope was attached to the plastic piece to the... Read more

• Oven is too hot
• Little to no heat when baking
• Oven not heating evenly
• Element will not heat

I cannot not sing the praises of this company & their helpful & fast service. I am going to post the online site address w/my praises on my facebook page for my friends that live on ranches many miles from appliance repair shops & towns. The Oven in our house is for sure over 20 yrs old it was in this home when we bought it, the home is 33 yrs old & the Oven is a Wall Oven, there is not room for a standard Oven in this Kitchen. The Oven itself still looks very nice. About 8 yrs ago or more... Read more

• Element will not heat

I googled "drip pans for electric range" and came upon your web site as well as some others. After looking at three or four I decided to go with your company. The choices clearly described the pans available so I didn't have to guess which one would fit. The price was very good and they arrive in the mail two days after I ordered them. The drip pans fit perfectly. Thank you. Charles Cummings Read more

• Freezer not defrosting
• Too warm
• Fridge too warm
• Freezer section too warm

I ordered a freezer temperature control. I ordered from you because parts are certified. Last thing I wanted was to go through the replacement process with a part that didn’t work. I’m not a handy person by nature, and I have zero common sense. I watched the awesome instructional video that you provided with my order several times. Before receiving or even opening the package, I felt that I knew what to expect because I watched the video so many times. Before beginning, I made sure I had as... Read more

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

I ordered a replacement bin, and since the price was reasonable I ordered a second one to help with organization in my refrigerator. I thought it would be a week for the bins to arrive, but it only took three days(one of those was a Sunday). Read more

Snapped off the old part and snapped on the new one. All of two minutes. Read more

It was the day of my birthday June 6th when my wife came to me to tell me that the dryer was not working. Immediately I started to look for a new dryer from Best Buy and the rest. Then I said It would be better if I waited for 4th of July at which time I could find a better deal. This is when I decided to take it apart to see what was wrong. Initially, I thought of the belt that could be broken and I rotated the drum by hand and I heard a noise of the belt at times falling on the drum. I was... Read more

I followed the directions on several websites for repairs. The obvious place to start is the heating coil and thermostat. I checked the continuity of the coil and it was good with a reading of almost zero resistance. Next I read that there is no thermostat controls on my GE dishwasher so I followed another webpage that said the Sensor Turbidity Assembly acts like a thermostat so I replaced that. Wasted effort as that switch sensor was OK. Normally it has a light on when it is working, a... Read more

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

• Ice maker dispenses too much ice

I replaced the ice maker after replacing the ice try and before that the ice chute gasket. All easy fixes. However, I am still seeing some frost build-up leading me to believe that the issue is just a faulty design, which I have read other posts on. Just too much warm air gets in the ice maker because it is located in the refrigerator, plus warm air probably finds its way from the outside dispenser, up the chute into the ice maker. Oh well, nothing the occasional hair dryer won't take care of,... Read more

I opened the cover panel of the control board. I visually checked for burns on the board and verified all connectors were firmly seated. I opened the bottom of the unit, and I saw the service manual in a zip-lock bag. From this manual, I verified that the drain pump resistance is good, the start capacitor is good, and the lid switch is good. I entered diagnostic service mode. Persistent alarms are 4 and 25.Error 4 means Reset Monitor, while Error 25 means Pressure Sensor Dropout. I... Read more

After extremely poor support from WhirlpooI and researching numerous U-Tube videos, I fully troubleshot potential failed components and connections. All appeared to function properly, so I reassembled the unit and experienced the same problem as before. I then narrowed down the problem to either the Touchpad ($57+$8 shipping) or the control board ($295+shipping). If those did not work, then a new Microwave of better quality, reliability and support than original microwave, Unfortunately,... Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more