Refrigerator Gasket & Seal

The Gasket-Door (black) is an OEM component specifically designed for Whirlpool refrigerators. This rubber gasket forms a seal around the perimeter of the refrigerator door opening. It helps maintain interior temperatures and humidity levels.

Symptoms of a bad door gasket include:

• Inability to properly chill compartments and freezing performance issues  
• Excessive frost or moisture inside refrigerator sections
• Higher energy costs from inefficient temperature regulation
• Warm air infiltration indicated by higher than normal interior temps

Causes of degraded gasket performance typically include cracks, tears or compression set deterioration that compromise the sealed barrier over many years of use. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This fresh food door gasket creates the airtight seal between the refrigerator door and cabinet. Replacing a worn gasket restores proper sealing to keep cold air in, reduce moisture, and stabilize internal temperatures.

• Seals the fresh food compartment door to maintain cooling efficiency
• Helps prevent warm air leaks that cause condensation, frost, or extended run times
• Replaces gaskets that are torn, warped, cracked, or won't lie flat
• Signs of failure include visible gaps, moisture on the liner, doors not closing smoothly, or rising fridge temps

• Disconnect power before servicing
• Let the gasket warm to room temperature; use low heat or warm water to relax waves
• Pull the old gasket from its channel; on some models, loosen inner liner screws to remove/seat the gasket
• Press the new gasket fully into the groove starting at the corners; adjust door alignment if needed

Keep your fridge sealing tightly with this replacement door gasket. It restores the refrigerator door seal to help maintain proper cooling, reduce energy use, and limit moisture and frost buildup for consistent food storage. What it does:

• Seals the refrigerator door to prevent cold air leakage and maintain set temperature
• Helps reduce frost buildup and condensation inside the fresh-food compartment
• Lowers strain on the compressor caused by escaping cold air
• Commonly replaced when you notice warm spots, persistent moisture, visible gaps, or a door that won't seat properly

• Disconnect power and remove food from the door area before replacing the gasket
• Inspect the gasket mounting channel for debris or damage and clean before installing
• Avoid sharp tools that could tear the gasket during removal or installation
• After installing, allow the gasket to form and check the door seal; door may need to be closed slowly for final seating

This front pan seal replaces the worn gasket that seals the refrigerator's front drip/pantry pan, helping keep water contained and directing drainage properly to prevent puddling and odors. Fits the pan edge at the fridge base. What it does

• Creates a tight edge seal along the front of the refrigerator drain/drip pan to keep condensation and defrost water contained.
• Helps direct water toward the drain channel so it can evaporate or flow to the condenser pan.
• Reduces chance of water pooling on the floor near the refrigerator base.
• Can improve odor control by preventing trapped moisture under the pan.

• One front pan seal.

• High-level swap: remove lower kickplate (if present), peel out the old seal and press the new seal into the pan groove; follow OEM instructions for your model.
• Use gentle, even pressure to seat the seal fully into the pan channel; avoid stretching the seal excessively.
• If adhesive is used by the model, only apply OEM-recommended adhesive in small amounts.
• Disconnect power or follow safety steps before working near electrical components.

This evaporator block seal replaces the rubber gasket that seals the evaporator block assembly to the freezer cabinet, helping maintain proper airflow and prevent leakage. It restores a tight seal around the evaporator block for reliable cooling performance. What it does:

• Seals the evaporator block to the cabinet to prevent warm air intrusion and water leaks
• Helps direct refrigerant-condensed water into the drain rather than inside the cabinet
• Commonly used when you see frost build-up around the evaporator or water pooling in the freezer
• Helps maintain consistent cold temperatures by preserving the sealed evaporator area

• One evaporator block seal

• Designed for field replacement; inspect surrounding gaskets and mounting surfaces for damage before installing
• Clean and dry mating surfaces thoroughly to ensure a proper seal
• Use common hand tools; avoid over-stretching or cutting the seal during installation
• Disconnect power to the appliance before servicing and follow safety precautions for refrigeration components

A self-adhesive foam strip that cushions gaps and seals edges to reduce air leaks, vibration, and moisture intrusion. Simple peel-and-stick design makes it a fast way to restore proper sealing and quiet operation. What it does

• Creates a soft seal along doors, panels or trim to help stop cold air loss and drafts.
• Dampens vibration and rattles caused by loose or worn mounting surfaces.
• Helps block dust and moisture from entering seams and crevices.
• Works where a thin, compressible filler is needed for a snug fit.

• Clean and dry the mounting surface thoroughly before installation for best adhesion.
• Measure and trim foam to fit; peel backing and press firmly to adhere along the entire length.
• Avoid stretching the foam during installation; allow adhesive to set before regular use.
• If adhesive residue remains on hands or surfaces, use a mild solvent per manufacturer guidance.

This Seal QC Damper is the gasket that seals the refrigerator/freezer air damper to help maintain proper airflow and temperature control. It replaces a worn or damaged seal to reduce air leaks and improve cooling consistency. What it does:

• Seals the damper opening to prevent warm or humid air from entering the cooled compartment
• Helps maintain consistent internal temperatures and more efficient cooling
• Commonly replaced when the damper area shows visible gaps, cracks, or air leakage
• Can reduce frost buildup or uneven cooling caused by a compromised damper seal

• One damper sealing gasket

• Disconnect power before starting any repair to avoid electrical shock
• Remove the damper housing or cover per your model's service instructions to access the seal
• Inspect the damper and surrounding area for damage; clean mating surfaces before installing the new seal
• Handle gently and seat evenly to ensure a full seal; test operation after restoration of power

This evaporator cover gasket seals the evaporator cover to the refrigerator cabinet, helping maintain proper airflow and reducing frost buildup behind the back wall. It restores a tight seal for more reliable cooling performance. What it does:

• Seals the evaporator cover to prevent air leaks that can cause frost or ice buildup
• Helps maintain consistent cold-air circulation in the freezer/refrigerator compartment
• Reduces chances of excessive frost, water pooling, or longer run cycles tied to air infiltration
• Supports normal defrost operation by keeping warm, moist air out of the evaporator cavity

• Disconnect power before servicing and allow the appliance to defrost if needed
• Remove the evaporator cover carefully; watch for sharp sheet-metal edges and retain fasteners
• Position gasket evenly around the cover mating surface; avoid stretching or creasing the seal
• If adhesive or clips are used, replace or reapply per OEM guidance to ensure a secure fit

This right-side evaporator cover gasket seals the evaporator cover to help prevent air leaks and reduce frost buildup, supporting consistent cooling and efficient refrigerator operation. What it does:

• Seals the evaporator cover to minimize warm air intrusion and reduce ice accumulation on the evaporator
• Helps maintain stable compartment temperatures for better cooling performance
• Reduces moisture and dripping that can cause water pooling inside the cabinet
• Can address symptoms such as increased frost on the evaporator, higher-than-normal temperatures, or water inside the fresh food/freezer area

• Disconnect power to the appliance before beginning any repair
• Remove necessary interior panels or shelves to access the evaporator cover per the service manual
• Seat the gasket fully around the cover flange; inspect the cover and seating surface for damage or debris