Spring Parts

This replacement spring restores the correct tension in the affected mechanism on your appliance, helping parts return smoothly and stay aligned. A fatigued or broken spring can cause loose action, noise, or improper engagement—this fixes it fast. What it does

• Provides return tension to the related mechanism so parts move and reset correctly
• Helps maintain alignment and reduces looseness or rattle during operation
• Supports smooth engagement/disengagement of linked components
• Common symptoms: weak/loose action, parts not returning to position, squeaking/rattling, visible break or deformation

• 1 spring

• Disconnect power; for gas appliances, shut off gas. For washers, also turn off water supply.
• Support the component under spring tension before removal to prevent sudden release.
• Note or photograph original routing and anchor points to match orientation on reassembly.
• Inspect related brackets/clips; replace any that are bent, worn, or corroded.

The Shock Absorber Kit is an OEM part for LG washing machines. This part minimizes vibrations and absorbs shocks during the washing and spinning cycles. By stabilizing the drum, these shock absorbers ensure smooth and quiet operation, preventing excessive movement and potential damage to the washer.

Causes of a bad shock absorber can include wear and tear over time, heavy or unbalanced loads that put extra strain on the absorbers, or damage from impact or mishandling. 

Symptoms of a bad shock absorber include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or knocking noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

This OEM LG part is also compatible with Sears/Kenmore.

This idler spring maintains proper tension on the dryer's drive belt by pulling the idler arm. Replacing a weak or broken spring restores consistent drum rotation and helps prevent belt slippage and noise.

• Applies tension to the idler pulley arm to keep the drive belt tight
• Helps the motor turn the drum smoothly without belt slip
• A worn, stretched, or broken spring may cause the drum not to turn or the belt to slip off
• Can contribute to squealing or chirping from the belt/pulley area

• Disconnect power; turn off gas supply for gas dryers
• Access the belt path; note belt routing and spring attachment points before removal
• Release belt tension, move the idler arm, attach the new spring, and re-tension the belt
• Rotate the drum by hand to verify belt tracking before reassembly and test run

This rear shock absorber kit stabilizes the washer tub by damping movement and vibration. Replacing a worn shock restores smoother, quieter spins and helps prevent the drum from banging the cabinet or the machine from walking. What it does:

• Dampens tub movement to control vibration during wash and spin
• Helps prevent banging/thumping noises and cabinet contact
• Reduces "walking" or excessive shaking of the washer
• Can help minimize out-of-balance interruptions

• One rear shock absorber kit

• Disconnect power and turn off water before servicing
• Support the tub/drum to relieve load before removing the shock
• Remove retaining pins/bolts; install the new shock in the same orientation and transfer any reusable hardware
• For consistent damping, replacing shocks in pairs or as a complete set is commonly recommended

The Door Spring is an OEM part for GE dishwashers. This part provides the necessary tension to the dishwasher door, allowing it to open and close smoothly and securely. The door spring helps balance the door’s weight, preventing it from falling open too quickly or slamming shut.

Causes of a bad door spring can include wear and tear from frequent use, stretching or breaking due to overloading the door, or damage from improper handling. 

Symptoms of a bad Door Spring include:

• The door falling open quickly without resistance
• Difficulty in keeping the door open at a desired angle
• The door slamming shut instead of closing gently
• Unusual noises when opening or closing the door

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This front shock absorber kit stabilizes the washer's tub during spin to reduce vibration and noise. Replacing worn dampers helps restore smooth operation and protects the cabinet and suspension from excessive movement.

• Dampens and controls tub movement during wash and spin
• Helps reduce shaking, "walking," and loud thumping/banging noises
• Can help when the washer won't reach or maintain full spin due to imbalance
• Replaces weakened or damaged front shock mounts/dampers

• Disconnect power and water before servicing
• Access shocks per your model's procedure; support the tub to relieve load
• Install with mounts aligned and fasteners tightened securely; verify free tub movement
• Many replace shocks in pairs to maintain balanced damping

The Door Spring is an OEM part for Frigidaire dishwashers. It provides smooth opening and closing of the dishwasher door by maintaining tension and balance. This spring ensures that the door moves gently and stays in place when opened, preventing slams that could lead to damage or injury.

Symptoms of a bad Door Spring include:

• A door that falls open abruptly or feels heavier than usual 
• Difficulty in keeping the door open 
• Noticeable wear or rust on the spring 
• Unusual noises when opening or closing the door

Causes of a bad part can include normal wear and tear over many cycles of use, corrosion from exposure to moisture, and mechanical failure due to improper alignment or installation.

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Note: Also, consider checking the door spring linkage 154325201.

The Suspension Spring is an OEM part for LG washing machines. It helps support the washer tub, reducing vibrations and absorbing shocks during the washing and spinning cycles, ensuring smooth and quiet operation.

Causes of a bad suspension spring can include wear and tear from regular use, overloading the washer, or damage from unbalanced loads. Over time, the spring can lose its tension or break, compromising the washer's stability and performance.

Symptoms of a bad suspension spring include:

• Excessive shaking or vibrating during the wash or spin cycles
• Loud banging noises
• The washer moving or shifting during operation
• Uneven or incomplete washing or spinning

This OEM LG part is also compatible with Sears/Kenmore models.

The Dishwasher Door Spring is an OEM replacement part for Whirlpool dishwashers. It helps with smooth opening and closing by providing a well-balanced counterforce. 

Causes can involve coils weakening from repeated engagements over time. Metal fatigue diminishes recoil capabilities as well reducing assistive power.

Symptoms of a problematic spring include:

• Sagging or loosely fitting doors
• Difficulty fully opening or closing door
• Noises occurring from unbalanced movement

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore dishwashers.

Dishwasher door balance spring. Also check the door balance link kit 8194001.

The Suspension Rod Kit is an OEM part for Whirlpool washing machines. This kit includes suspension rods that are designed to support and stabilize the washing machine tub during the wash and spin cycles. 

Causes of a bad suspension rod can include regular wear and tear, overloading the washing machine, or damage from heavy loads that place excessive stress on the rods. 

Symptoms of a bad suspension rod include:

• Excessive shaking or vibrating during the wash or spin cycles
• Loud banging or knocking noises during operation
• The washing machine tub being off-balance or leaning to one side
• The washer moving or "walking" across the floor during use

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Plunger Spring is an OEM part for GE dishwashers. This spring is part of the door latch mechanism, helping to ensure that the dishwasher door latches and unlatches properly. It provides the necessary tension to keep the door securely closed during operation, preventing leaks and ensuring the appliance runs efficiently.

Causes of a bad plunger spring can include wear and tear from regular use, corrosion due to exposure to moisture, or physical damage such as bending or breaking. Keeping the plunger spring in good condition is crucial for the proper functioning of the door latch.

Symptoms of a bad plunger spring include:

• Difficulty in latching or unlatching the dishwasher door
• The door not staying securely closed during operation
• Water leaking from the door
• The door feeling loose or not closing properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Suspension Springs are an OEM replacement part for Whirlpool washing machines. This set contains two heavy-duty coil springs designed to absorb vibrations caused by unbalanced or off-center loads inside the washer tub.

Causes of bad springs can include cracks or fractures from extended use, overloading, mineral buildup hampering flexibility, or rust accumulating over many years.

Symptoms of bad or broken suspension springs include:

• Excessive vibration and shaking even with balanced loads
• Loud banging or thumping noises during cycles
• Hissing or squeaking that worsens over time
• Gradual misalignment of the tub on support rails

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Spring Closure is an OEM part for GE refrigerators. This spring aids in the automatic closing of the refrigerator door, ensuring it seals tightly after each use to maintain optimal internal temperatures.

Causes of a bad spring closure can include regular wear and tear, corrosion due to moisture, or accidental damage that compromises its function.

Symptoms of a bad spring closure include:

• The refrigerator door not closing completely or staying ajar
• Difficulty in opening or closing the door smoothly
• Increased energy consumption as cold air escapes
• Frost buildup around the door seal area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Control Plate Spring is an OEM part for Whirlpool stand mixers. This spring maintains the proper tension and alignment of the control plate, ensuring the smooth operation and accurate adjustment of the mixer speeds.

Causes of a bad control plate spring can include wear and tear over time, stretching from continuous use, or damage due to overloading the mixer.

Symptoms of a bad control plate spring include:

• Difficulty in adjusting mixer speeds
• Mixer speeds not responding accurately to control adjustments
• Loose or unresponsive control lever
• Unusual noises during speed changes

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Door Spring is an OEM part for Whirlpool dishwashers. This part allows the smooth and controlled operation of the dishwasher door. The spring helps balance the weight of the door, allowing it to open and close effortlessly without slamming shut.

Causes of a bad door spring can include wear and tear from repeated use, corrosion or rust, and breakage due to excessive force or mishandling.

Symptoms of a bad door spring include:

• The dishwasher door dropping quickly or not staying open
• Difficulty in opening or closing the door
• Unusual noises when moving the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This torsion spring mounts in the dispenser to return the ice chute door/flapper to the closed position after dispensing. Replacing a weak or broken spring helps stop warm air leaks, frost, and ice clumping in the chute.

• Provides the closing force for the dispenser ice door
• Helps seal the ice chute to reduce frost and moisture intrusion
• Typical symptoms: ice door won't close fully, frost/ice buildup around the chute, cubes dropping after dispensing, or air leakage at the dispenser
• Replace if the spring is broken, deformed, or has lost tension

• Disconnect power before servicing; shut off water if working near the dispenser area
• Remove dispenser trim/bezel and control panel to access the ice door assembly; support wiring harnesses
• Note spring orientation and preload before removal; install the new spring on the same hinge posts in the same direction
• Manually cycle the flapper to ensure smooth return and a full seal before reassembly