Gasket & Seal

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

I followed the very well made repair video for this particular part. The total time it took for the repair was under 20 minutes. But I have a suggestion for the repair video and that is to emphasize that when reinstalling boot. Have the tachnician point out that there are drain holes in the boot that need to be situated and reattached toward the bottom of the washer chassis. Unfortunately I had to redue and double the repair time because the wash water would not drain properly during wash... Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

Replaced the bellow. Read more

• Takes too long to dry

Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more

From reading "troubleshooting" sites on the internet, originally thought I'd be replacing the front & rear drum rollers, so I ordered the rollers, and a new belt before I opened up the dryer, taking it out of use. When I opened it up the front rollers were "shot", and the front bulkhead was "totaled". Waited for parts to arrive (within 2 days), and successfully replaced front & rear rollers, bulkhead, drum seal. The on-line videos really helped me ensure I was keeping in the right order. My... Read more

This process was fairly straightforward, it took a couple of hours. I watched a video on youtube and followed the directions. The trickiest part was attaching the diaphragm to the tub. The weights were in the way and made it difficult to seal. I ended up removing the weights and it went on much easier. Read more

Purchased the gasket, but upset with myself I forgot the high temp adhesive.....a 13$ part and now 7$ for shipping. Think not for my mistake Read more

I replaced the gasket. Removing the old one was not easy. I used a razor knife to cut out most of it. And then I used rubbing alcohol to soften the remaining glue and scrapped it out with a small blade screwdriver Read more

If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day. NOTE! The retaining rings are... Read more

• Leaking

In reality, this turned into a full-on rebuild project - with several parts orders, not just a simple repair. But I have to give credit: The parts listings with pictures on the AppliancePartsPros web site were really useful in figuring out what was going on inside the machine, and what parts I would need. Also: The repair videos were critical for me to be able to ensure I was reassembling everything correctly. Shout out to Simon, who was featured in several of the repair videos. His "gorgeous... Read more

Replaced the upper and lower felt strips and drum glides. Dryer running much quieter and not tearing clothes. Read more

LG Washing Machine WM3885HCCA I searched the Appliance Parts Pros "Get Repair Help" tab, typed in the LG washing machine model number (WM3885HCCA), watched videos and searched for the parts shown on the diagrams of my LG washing machine. After finding parts, I confirmed on both the Appliance Parts Pros site and LG site that the parts I selected were correct. I highly recommend using the LG site . I was able to type in the original part number from the Appliance Parts Pro site and LG directed... Read more

• Leaks water

Noticed large banging in the washing machine when transitioning from low to high speed spin. Also would get a slight smell of burnt rubber. Did an online search and best guess was the spider arm assy was broken. Ordered the spider arm assy, the rear tub seal and the tub seal. Make sure you get blue threadlocker - you'll use it multiple times during the reassembly. The washer is 9 years old and is heavily used. Used the online video on the appliancepartspros.com site to handle the repair. The... Read more

Just like the one's I have worked on for 30 years for Whirlpool. Read more

Initially did a uTube search for specific instructions on dismantling this machine for this repair. I had successfully replaced a door/tub gasket on a Whirlpool front load machine previously. Did not find specific uTube instructions for this Kenmore. So began removing parts using past learned info on what needed to be removed first, second, and last. Removed the top, detergent dispenser screws/control panel, then the front (with a couple hidden screws around drain pump filter) and the front... Read more