Parts for Lg WM3488HS/00: Other Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This duct outlet directs a dryer's exhaust from the cabinet to the external vent, helping maintain proper airflow and reduce leaks. It replaces a damaged or worn outlet flange to restore safe venting. What it does:

• Channels dryer exhaust from the cabinet to the vent hose or duct
• Helps maintain proper airflow for efficient drying
• Prevents exhaust leaks that can cause poor performance or odors
• Reduces rubbing/interference that can create noise when damaged

• One duct outlet

• Disconnect power before servicing; for gas dryers, turn off the gas supply and disconnect per local codes
• Use basic hand tools; avoid bending the outlet flange to prevent cracks
• Verify a secure seal with the vent hose after installation and test operation

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

The Shipping Bolt Assembly is an OEM part for LG washing machines. This assembly is used to secure the washer drum during transportation, preventing it from moving and getting damaged. Shipping bolts are essential for maintaining the integrity of the washing machine when it is being moved or installed.

Causes of a bad or missing shipping bolt assembly include improper handling during moves, wear and tear from multiple uses, or not reinstalling them when relocating the washer. Ensuring that the shipping bolts are in place is crucial for protecting the internal components of the washer during transit.

Symptoms of a missing or damaged shipping bolt assembly include:

• Excessive movement or shaking of the drum during transportation
• Internal components of the washer getting damaged during a move
• Difficulty in securing the drum for transport
• Noise or instability during washer installation

This OEM LG part is also compatible with Sears/Kenmore.

This outer tub assembly is the main watertight housing that supports the washer drum and contains wash water. Replacing a damaged outer tub restores the washer's ability to hold water and properly support the rotating drum. What it does

• Holds and seals wash water inside the washer to prevent leaks.
• Supports the inner drum and bearings for smooth rotation.
• Helps maintain correct alignment between the drum and motor/drive components.
• Often replaced when cracks, distortion, or corrosion cause leaks or unusual noise.

• One outer tub assembly.

• Disconnect power and water supply before beginning service.
• Replacing the outer tub typically requires removing panels, the inner drum, and drive components; have the correct tools and a service manual for your model.
• Inspect and replace related seals, gaskets, bearings, and fasteners as needed.

Direct-replacement display power control board assembly that restores power and control to the appliance's display and front control panel. Replaces a failed display module to get buttons, lights, and on-screen messages working again. What it does:

• Supplies power and control signals to the appliance display and front user interface.
• Restores responsive buttons, touch controls or soft keys when the display electronics fail.
• Stops or reduces display issues such as a blank, flickering, or dim screen.
• Helps address intermittent display behavior or loss of display backlight.

• Disconnect the appliance from power before starting work to avoid shock or short circuits.
• Handle the board by its edges and use ESD precautions (avoid static discharge) to protect electronic components.
• Keep track of screws and connectors; transfer any shields or mounting hardware from the old board if required.

The Tub Bearing is an OEM part for LG washing machines. This bearing supports the washer drum, allowing it to spin smoothly during the wash and spin cycles. The tub bearing ensures the drum rotates quietly and efficiently, contributing to the overall performance and longevity of the washing machine.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads, or moisture and detergent residue leading to corrosion. 

Symptoms of a bad tub bearing include:

• Loud noises or grinding sounds during the spin cycle
• The washer drum not spinning properly or wobbling
• Water leaks from the bottom of the washer
• Excessive vibration or shaking during operation

This OEM LG part is also compatible with some Kenmore models.

The Tub Bearing is an OEM replacement part for LG washing machines. It is a crucial component that supports the weight of the tub and allows for smooth rotation during the wash and spin cycles.

Causes of a bad tub bearing can include excessive wear over time due to high-speed spinning, damage from overloading or unbalanced loads, or lack of proper lubrication.

Symptoms of a bad tub bearing include:

• Loud grinding or growling noises during the wash or spin cycle
• Excessive vibrations or shaking of the washing machine
• Leaks due to increased stress on the tub and other components
• Difficulty in starting or maintaining the spin cycle

This OEM LG part is also compatible with Sears/Kenmore models.

The Motor Rotor Bolt is an OEM part for LG washing machines. It secures the rotor to the motor shaft, playing a crucial role in the efficient functioning of the motor and ensuring the washer drum spins correctly during wash cycles.

Causes of a bad motor rotor bolt can include wear and tear from prolonged use, corrosion due to exposure to moisture, or damage from over-tightening or accidental impacts. A faulty motor rotor bolt can compromise the stability of the motor, leading to various operational issues.

Symptoms of a bad motor rotor bolt include:

• The washer drum not spinning or spinning irregularly
• Unusual noises during operation, such as banging or clunking
• The washer failing to complete cycles or stopping mid-cycle
• Visible wear or damage to the bolt or surrounding components

This OEM LG part is also compatible with Sears/Kenmore models.

The Tub Seal Gasket is an OEM part for LG washing machines. It creates a tight seal between the inner and outer tubs during the wash cycle, preventing leaks and containing water. The gasket helps prevent water from escaping the tub. 

Causes of a bad gasket can include wear and tear from repeated use over time, exposure to cleaning chemicals or extreme temperatures, or damage from handling heavy loads. 

Symptoms of a bad gasket include: 

• Water leaking from the outer tub during operation
• Excessive moisture in areas surrounding the washer 
• The tub making creaking or grinding noises
• Decreased washing or spinning performance

This OEM LG part can also be used on Kenmore/Sears appliances. 

This clamp assembly secures a hose, tube, or similar connection inside your appliance, maintaining a tight, reliable hold to prevent leaks and movement. Replacing a worn or damaged clamp restores proper sealing and dependable performance.

• Holds a hose/tube or component firmly in place to help prevent leaks or disconnections
• Reduces movement and vibration that can cause noise or wear
• Restores clamping force when the original is bent, corroded, or stretched
• Common symptoms: drips at a joint, hose slipping off, rattling, or a missing/broken clamp

• Disconnect power; shut off the water supply if the clamp secures a water line
• Place a towel or pan to catch residual water and relieve line pressure if applicable
• Note the original orientation; use suitable hand tools to release and seat the clamp securely
• Inspect the hose/tube and fitting for damage; replace if cracked or deformed and check for leaks after reassembly

This replacement refrigerator door gasket seals the door to keep cold air inside, helping restore proper cooling and reduce frost, condensation, and energy loss from a damaged or worn seal. What it does:

• Creates an airtight seal around the refrigerator door to maintain internal temperature.
• Prevents warm air infiltration that can cause frost buildup and uneven cooling.
• Reduces condensation and helps improve compressor efficiency when sealing properly.
• Common symptoms of a failing gasket: visible cracks or gaps, cold air leaks, frost or moisture buildup, and higher energy use.

• Remove the old gasket and clean the door flange before installing the new seal.
• Press the gasket evenly into the door channel; some models use retaining clips or screws—model-specific instructions.
• Check that the gasket seats uniformly with the door closed and make minor adjustments as needed.

This is a motor harness intended for use with washing machines. The motor harness is a wiring component that's attached to the washing machine's motor and is used to conduct electricity between the motor and the PCB. Wear and tear, damage, or other issues can arise with the motor harness over time. When there is a malfunction or failure with this component, a replacement part is necessary to continue the appliance's efficient and safe use.Signs that something has gone wrong with the washing machine's motor harness include intermittent operations or a device that won't run at all. Replacing the motor harness is a relatively easy task. Disconnect the appliance from power and wear work gloves for safety. Ensure all connections between the motor and motor harness are secure before plugging the washing machine back into to avoid the motor's accidental activation.This motor harness is an authentic OEM replacement part. It is sold as an individual unit. The motor harness is made of high-quality, durable materials. It comes sourced directly from the manufacturer to ensure compatibility. The motor harness can be installed in various models of washing machines. It fits correctly into appliances produced by Kenmore and LG.

This door assembly replaces a damaged or dented outer refrigerator door to restore proper sealing, appearance, and safe operation. It provides the door shell, mounting points and openings for handles and trim so the fridge closes correctly. What it does

• Replaces a cracked, dented or bent outer refrigerator door to stop air leaks and improve appearance
• Restores proper door alignment and sealing to help maintain internal temperature
• Provides factory mounting points and openings for the handle, hinges and trim pieces
• Works with existing inner liner, gasket and internal components when those parts are undamaged

• Disconnect power and empty the door of food and removable shelves before starting
• Door assemblies are heavy and awkward—have a second person to help lift and align safely
• Basic hand tools required; hinge screws and fasteners typically transfer from the old door
• Follow model-specific service instructions for hinge alignment and gasket seating

This door inner frame is the replacement inner panel frame that supports the door liner and trim, restoring proper fit and appearance. It helps keep the door assembly aligned and finished for normal operation and seal integrity. What it does:

• Provides structural support for the door liner and attached trim pieces
• Restores correct alignment and fit of the door assembly
• Helps maintain a proper door seal and reduces drafts or uneven closing
• Replaces cracked, warped, or cosmetically damaged inner door framing

• One door inner frame

• Disconnect power to the appliance before starting any door repair
• Removal typically requires taking off door trim and inner liner; keep fasteners organized
• Inspect door gasket, hinges, and hardware while replacing the frame; replace any damaged hardware

This locker hook engages the appliance's latch/lock mechanism to keep the door securely closed during operation. Replacing a worn or bent hook restores reliable latching and helps prevent nuisance door/lock errors and cycle interruptions.

• Interfaces with the door lock/latch to secure the door during use
• Allows the safety interlock to confirm the door is closed
• Common symptoms: door won't latch or stay closed, needing to hold/push door to start, door/lock error messages
• Physical signs of failure: bent hook, worn contact surface, or cracked/broken mounting ears

• Disconnect power; turn off water supply if applicable
• Access the hook location on the door or cabinet/tub (varies by model); remove mounting screws/clips
• Transfer any reusable hardware; align the new hook so it mates cleanly with the latch/lock and tighten fasteners
• Close the door to verify smooth engagement before running a cycle

This is the refrigerator's water inlet valve assembly. It controls and directs household water into the dispenser and ice maker as needed, restoring proper water flow and ice production.

• Opens to supply water to the ice maker and dispenser when energized
• A common fix for no/low water at the dispenser
• Can resolve no ice production due to no water fill
• May address leaks or continuous dripping from the dispenser/ice maker
• Failure can present as buzzing or clicking with little/no water flow

• Disconnect power and shut off the water supply before servicing
• Have a towel or small container ready to catch residual water
• Note hose and wire locations or take photos before removal
• After installation, restore water and power, then check for leaks and run a test fill

The Water Inlet Valve Assembly is an OEM replacement part for LG washing machines, designed to control the flow of water into the laundry tub. This part is responsible for opening and closing to allow water into the wash drum at the appropriate times during the wash cycle, providing the correct water level and temperature.

Causes of a bad Water Inlet Valve Assembly can include mineral deposits blocking the valve, electrical failure preventing the valve from opening or closing properly, or physical damage to the valve mechanism itself.

Symptoms of a bad Water Inlet Valve Assembly include:

• Inadequate filling of the washer drum
• Water entering the drum when the washer is off
• Unusual noises during the fill cycle
• Water that is too hot or too cold, indicating a failure in valve operation that controls temperature

This OEM LG part can also be used on Kenmore/Sears appliances. 

This Thermostat Assembly monitors and regulates internal temperature within the appliance's heating circuit. Replacing a failed thermostat restores proper heat control, helps prevent overheating, and can resolve common heating performance issues so cycles run correctly. What it does

• Senses internal temperature and opens/closes the heater circuit to maintain proper heat
• Provides over-temperature protection by cutting power at unsafe temperatures
• Helps ensure consistent heating performance throughout the cycle
• Helps with symptoms such as no heat, overheating/shutting off, or unusually long cycle times

• 1 thermostat assembly

• Disconnect power before servicing; allow hot components to cool
• Access the thermostat location (varies by model); note wire positions before removal
• Mount flush to the surface for accurate sensing; transfer original hardware if required
• After installation, test operation; use a multimeter for continuity checks if needed

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

Restore stable, level support with this replacement leg assembly. The adjustable foot steadies the unit on uneven floors, reducing vibration and rattling while allowing precise leveling for proper alignment and smooth, reliable operation.

• Provides adjustable support at the base of the unit
• Helps keep the appliance level on uneven or sloped floors
• Reduces wobble, vibration, and rattling noises
• Promotes proper door alignment and closure
• Replaces stripped, cracked, or missing leg assemblies

• Disconnect power; shut off water supply if applicable
• Carefully tilt and support the appliance to access the leg area
• Unthread the old leg; hand-thread the new assembly to avoid cross-threading, then fine-adjust with a wrench
• Level front-to-back and side-to-side; confirm stability before use

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This wire harness routes power and signals between the washer's control and multiple components. Replace a damaged harness to restore dependable operation when wiring is cut, brittle, or connectors are heat-damaged or corroded.

• Distributes electrical power and communication between the control board and components such as the motor, pump, valves, door lock, and sensors
• Maintains safe, reliable connections when insulation and terminals are intact
• Typical failure signs: intermittent operation, no start, specific loads not working (pump/motor/valves), or error codes traced to wiring faults
• Visible damage like chafed wires, broken connector locks, or burned/corroded terminals indicates replacement

• Disconnect power and turn off water supply before servicing; wear cut-resistant gloves
• Photograph and label connectors; move one plug at a time from old to new to avoid miswiring
• Route along original clips, channels, and grommets; keep wiring clear of sharp edges and moving parts
• Ensure all connectors are fully seated; test operation before final reassembly

This inlet hose routes household water into the appliance so it can fill and operate correctly. Replacing a damaged inlet hose restores proper water flow and prevents leaks that can cause poor performance or water damage. What it does:

• Channels incoming water from the household supply into the appliance
• Stops leaks and restores normal fill when the original hose is cracked, split, or worn
• Helps correct symptoms like no water entering the appliance, slow or intermittent fill, or visible leaking at the hose connection
• Works with the appliance's valve and fittings to maintain a sealed water path

• Turn off the water supply and unplug the appliance before starting any work
• Inspect fittings and seals; replace any worn gaskets to ensure a watertight connection
• Hand-tighten connections then check for leaks; avoid overtightening plastic fittings

This part may be black or gray in color.

This heater assembly restores consistent, controlled heat inside your appliance so cycles reach the correct temperature. Replacing a failed heating element assembly helps resolve no-heat complaints and performance issues that leave loads cold or extend run times.

• Generates the heat required during the appliance's heating phases so temperatures rise as intended
• Works with thermostats/sensors to achieve and maintain target temperature
• Typical symptoms: no heat, lukewarm operation, unusually long cycles, or heating-related error codes
• Often confirmed by an open element or out-of-range resistance in continuity tests

• Disconnect power and allow the appliance to cool completely before servicing
• Access the heater per the service documentation; photograph wiring and routing to aid reassembly
• Handle the element carefully to avoid bending or damaging coils; transfer any brackets/sensors from the original if they are not supplied with the new part
• After installation, inspect and clear airflow or circulation paths and verify correct voltage before test operation

This inlet hose connects your appliance to the household water supply, delivering water where needed and helping prevent leaks at the connection. Use it to restore reliable water fill and flow. What it does:

• Transfers cold (or cold/hot where applicable) water from the household supply to the appliance
• Provides a sealed connection at the inlet to prevent drips and leaks
• Restores normal water fill when a cracked or blocked hose is causing no/low fill
• Helps correct intermittent filling or water pressure issues caused by damaged hoses

• Turn off the home's water supply and unplug the appliance before replacing the hose
• Inspect the hose ends and gaskets; replace gaskets if worn to ensure a watertight seal
• Hand-tighten fittings, then give a firm quarter-turn with a wrench; do not overtighten
• After installation, restore water and power, then check connections for leaks during an initial fill cycle

The Drain Pump and Motor is an original LG (OEM) replacement part for LG made washing machines that is responsible for removing water from the washer at the end of the wash cycle. The pump forces water out through the drain hose so that clothing comes out free of excess water, making the drying process faster. 

Symptoms of a failing Drain Pump Motor include:

• Water not draining out of the washing machine 
• Noisy or unusual sounds coming from the pump area during the drain cycle
• The washing machine stopping mid-cycle

Causes of a bad Drain Pump Motor can range from obstructions in the pump or hose, which can strain or damage the motor, to wear and tear from regular use leading to motor failure. Electrical issues can also affect the motor's performance, preventing it from operating correctly.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Drain Pump Assembly is an OEM part for LG washing machines. This part removes water from the washer's tub during the drain cycle.  

Causes of a bad drain pump assembly can include blockages from debris or small clothing items, wear and tear on the pump motor, or damage to the pump's impeller.  

Symptoms of a bad drain pump assembly include:

• Water not draining from the washer
• Loud or unusual noises during the drain cycle
• Error codes related to drainage issues
• Water leaking from the pump area

This OEM LG part is also compatible with some Kenmore models.

AC pump motor assembly replaces a failed pump drive to restore proper water removal. Direct-fit replacement restores pump operation to stop standing water, noisy pumping, or continuous filling issues in compatible LG machines. What it does:

• Drives the washer/dishwasher pump to move water out of the tub or through the circulation system.
• Restores proper drainage when a worn motor causes the unit to fail to pump water.
• Stops humming, grinding, or high-pitched noises caused by a failing pump motor.
• Helps prevent leaks or overflow caused by a non-operating pump (when pump seals and hoses are intact).

• Always unplug the appliance and shut off water supply before starting repairs.
• Access the pump from the front/bottom service panel; support the tub or cabinet as needed to avoid strain.
• Keep original wiring orientation and mounting hardware; transfer gaskets/seals or replace if damaged.
• After installation, run a test drain cycle to ensure proper operation before full reassembly.

The Pump Filter Assembly is an OEM replacement part for LG washing machines. It is a crucial component that filters out lint, debris, and other particles from the wash water, preventing them from recirculating and damaging the pump or other internal components.

Symptoms of a need to replace the pump filter assembly:

• Clogging or blockages, leading to poor drainage or water not draining completely
• Excessive buildup of lint, hair, or other debris in the filter screen
• Leaks or water seeping from the filter housing or surrounding area
•  Unusual noises or vibrations during the drain or spin cycles, indicating a potential blockage

Causes of a faulty pump filter assembly can include excessive lint accumulation, damage to the filter screen or housing due to impact or mishandling, and general wear and tear over time.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

This hinge spring restores proper tension to the door so it opens and closes smoothly and stays aligned. Replacing a fatigued spring helps prevent sagging or slamming and supports a consistent, reliable door close.

• Provides the return tension/counterbalance for the door hinge mechanism
• Assists smooth opening/closing and helps the door stay properly aligned when latched
• Helps maintain consistent closing force over time
• Failure symptoms include: door drops quickly, won't stay aligned or fully closed, weak/squeaking spring action

• Disconnect power before service; allow any hot surfaces to cool
• The hinge and spring are under tension—support the door and release/install tension carefully
• Note spring orientation and hole positions before removal; match them on installation
• Access may require removing trim or the door; keep fasteners organized for reassembly

This pressure switch assembly monitors the washer's tub water level and signals the control to fill, drain, and advance cycles properly. Replacing a faulty switch restores accurate water level sensing for reliable washing performance.

• Senses air pressure from the tub to determine water level
• Helps prevent overfilling and underfilling
• Common failure symptoms: overfills or won't fill, won't advance to spin/drain, drains continuously, or shows a PE (water level sensor) error
• Can cause intermittent cycle stops when readings are inaccurate

• Disconnect power and turn off water supply before servicing
• Access is typically from the top/console area; note hose and connector positions
• Inspect/clear the pressure hose; ensure it's not cracked, kinked, or blocked
• Seat the hose fully on the barb and reconnect the wire harness securely; test a fill cycle for proper operation

The Suspension Spring Holder is an OEM part for LG washing machines. This holder supports the suspension springs that help stabilize the washer drum during operation, reducing vibration and movement. It plays a critical role in ensuring smooth and quiet operation of the washing machine.

Over time, the suspension spring holder can become worn or damaged due to regular use, heavy loads, or accidental impacts. Causes of a bad suspension spring holder include wear and tear, physical damage, or corrosion from moisture exposure.

Symptoms of a bad suspension spring holder include:

• Excessive vibration or shaking during wash cycles
• Unusual noises, such as banging or clunking
• The washer drum appearing misaligned or sagging
• The washing machine moving or walking during operation

This OEM LG part is also compatible with Sears/Kenmore.

The Pump Hose is an OEM replacement part for LG washing machines. It is a flexible tube that connects the pump assembly to the internal tub and spins through the detergent dispenser area. The pump hose is responsible for circulating and removing water during the wash and rinse cycles. 

Symptoms of a bad pump hose include:

• Leaks or water not fully draining from the washer 
• Slow or inefficient filling and draining of water  
• Pump running loudly or continuously
• Wet areas under or around the washer

Causes of failure can be cracks or splits developing in the tubing from repeated bending and flexing over time, or blockages restricting water flow.

It is also compatible with some Kenmore models.

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

The Door Switch is an OEM part for LG washing machines. It is responsible for detecting whether the washer door is securely closed or open. The door switch ensures that the washer operates only when the door is properly closed and latched.

A bad washer door switch can occur due to wear and tear over time, electrical malfunctions, or physical damage. If the door switch fails, it can prevent the washer from starting or cause it to stop mid-cycle, resulting in inconvenience and disruption to your laundry routine.

Symptoms of a bad washer door switch include:

• Washer not starting or powering on.
• Washer not completing cycles or stopping abruptly.
• Inability to lock or unlock the washer door.

This OEM LG part can also be used on Kenmore/Sears appliances.

This clamp assembly secures a hose or tubing connection to maintain a watertight seal and reduce vibration. Replacing a worn or damaged clamp helps stop leaks and prevents hoses from slipping loose during operation. What it does:

• Holds a hose or tube firmly in place to maintain proper sealing at the connection point.
• Prevents leaks caused by loose, cracked or corroded clamps.
• Reduces vibration and rattling from unsecured hoses.
• Common symptom: visible leaking, water pooling, or a loose hose connection.

• Disconnect power and shut off water supply before starting any repair.
• Use the correct pliers or screwdriver for the clamp type; avoid damaging the hose.
• Inspect the mating hose and seal; replace any cracked or hardened hoses before reinstalling.
• Do not overtighten—tighten just enough to secure the hose without cutting or deforming it.

This main PCB power control board assembly controls the appliance's core electronic functions, restoring responsive controls and power distribution when the original board fails. Replaces a faulty main control module to help recover normal operation. What it does:

• Regulates and routes power to the appliance's electronic components and user interface
• Processes control inputs and sends commands to motors, valves, and sensors
• Common symptoms of a failing board: unresponsive controls, intermittent power, error codes, or no operation
• Used when diagnostics indicate the control board is the root cause of electrical/control failures

• 1 main PCB power control board assembly

• Disconnect power to the appliance before starting any service
• Handle the board carefully to avoid static discharge or damage to connectors
• Verify connector locations and orientation match the original before installing

The NOISE FILTER ASSEMBLY is an OEM part for LG washing machines. It is a component designed to minimize vibrations and reduce noise emanating from the washer during operation. Proper noise damping is important for smooth functionality without disturbance.

Causes of a bad noise filter assembly can include cracks or tears developing over extended use. Physical damage from impact could also compromise its noise-blocking abilities. 

Symptoms of a bad noise filter assembly include:

• Loud banging or clanking noises during wash and spin cycles
• Excessive vibrations felt through the washer cabinetry 
• Increased stress on other components from inadequate dampening
• Premature wear of suspension components like legs and runners

Replace yours today with this genuine OEM LG part to restore a quiet wash experience. This replacement assembly ensures optimum vibration control. It is also compatible with Sears/Kenmore models.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

The Gasket is an OEM part for LG washing machines. It forms a seal between the door and the drum, preventing water from leaking out during the wash cycle.

Causes of a bad gasket can include wear and tear over time, mold or mildew buildup, or physical damage from sharp objects or rough handling. Detergent residue and other factors can also degrade the gasket material.

Symptoms of a bad Gasket include:

• Water leaking from the washer door
• Visible tears, cracks, or deformities in the gasket
• Mold or unpleasant odors emanating from the gasket area
• The door not sealing properly, leading to inefficient washing

This OEM LG part is also compatible with Sears/Kenmore models.

This bellows is the flexible door boot seal that helps keep water contained in the washer tub and maintains a watertight seal around the front-load door. It replaces a damaged or leaking door boot to reduce leaks and restore proper sealing. What it does:

• Forms a flexible, watertight seal between the washer door and tub to help prevent leaks
• Keeps laundry water inside the drum during wash and rinse cycles
• Helps maintain drum pressure balance and proper door closing
• Commonly replaced when cracked, torn, or permanently deformed

• One bellows

• Recommended for front-load washers; fit with your model before ordering
• Typical replacement requires removing the outer and/or inner door trim and detaching clamp(s)
• Disconnect power and water supply before beginning any repair to avoid injury

Connector hose joins an appliance water line to internal plumbing, providing a sealed path for water. Replacing a damaged connector stops leaks and restores reliable water delivery to dispensers and ice makers.

• Joins and seals the appliance water line to the unit, preventing leaks and ensuring proper flow.
• Replace when you notice dripping, pooling under the appliance, or reduced water/ice production.
• Fits factory connection points for a secure, leak-resistant seal.
• Works with existing clamps and O-rings when those components are serviceable.

• Shut off the water supply and disconnect power before removing the old connector.
• Relieve water pressure by running the dispenser or dispensing water before disconnecting lines.
• Inspect and replace worn clamps or O-rings; hand-tighten fittings, then turn the water on slowly and check for leaks.

The Shock Absorber Kit is an OEM part for LG washing machines. This part minimizes vibrations and absorbs shocks during the washing and spinning cycles. By stabilizing the drum, these shock absorbers ensure smooth and quiet operation, preventing excessive movement and potential damage to the washer.

Causes of a bad shock absorber can include wear and tear over time, heavy or unbalanced loads that put extra strain on the absorbers, or damage from impact or mishandling. 

Symptoms of a bad shock absorber include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or knocking noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

This OEM LG part is also compatible with Sears/Kenmore.

The Hinge Pin is an OEM part for LG washing machines. It serves as a pivot point for the washer door, allowing it to open and close smoothly. This component is crucial for maintaining the proper alignment and function of the washer door, ensuring a secure and reliable seal during operation.

Common causes of a bad hinge pin include frequent use leading to wear and tear, physical damage from accidental impacts, or rust and corrosion over time. A compromised hinge pin can result in misalignment of the door, affecting the washing machine's ability to close properly and maintain an effective seal.

Symptoms of a bad hinge pin include:

• Difficulty opening or closing the washer door
• Door not staying securely closed during operation
• Squeaking or grinding noises when the door is moved
• Visible wear or damage to the hinge pin

This OEM LG part is also compatible with Sears/Kenmore models.

The Magnetic Door Plunger is an OEM part for LG washing machines. It is designed to securely hold the door in a closed position during the operation cycle, employing a magnet mechanism for enhanced reliability. The plunger ensures that the door latch is properly engaged, preventing the machine from running if the door is not closed correctly.

Causes of a bad Magnetic Door Plunger can include wear and tear from constant use, failure of the magnetic mechanism due to exposure to moisture or mechanical damage, or a misalignment that prevents the door from closing properly.

Symptoms of a bad Magnetic Door Plunger include:

• The washing machine door not staying closed during cycles.
• The machine failing to start due to a door sensor not detecting closure.
• Random pausing of the machine during operation if the door unlatches.

This OEM LG part is also compatible with Sears/Kenmore.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.