Refrigerator Valve

• Leaking
• Ice maker not making ice
• Not dispensing water
• Ice maker won't dispense ice

On your chat box with Kelsey, I decided it was probably the valve and so ordered a water valve. It came next day! Before trying to install it, I wanted to confirm whether it was the valve or the icemaker, so I chatted again with Kelsey who gave me a useful test (manually pour water into the icemaker) that confirmed the icemaker was functional. So I thought it surely is the valve, so I removed the old valve according to the very helpful video on your website. When I opened the box with the new... Read more

• Not dispensing water

Our Kenmore (Whirlpool) refrigerator's ice maker had stopped making ice. I searched YouTube and found a repair videos for this exact problem, finding one with a similar refrigerator and the identical ice maker. I learned that the Water Inlet Valve had likely gone bad and would need to be replaced. In the video the tech pointed out the small rubber tube inside the freezer that comes down from the ceiling of the refrigerator into the ice maker. This tube feeds it the water to make ice with and... Read more

I seared the web and found Appliance Parts Pros site and when I input my GE refrigerator model number I was able to do some diagnostics on their site. It was indicated from my research that the Water Inlet valve most likely was at fault for my problems. I ordered the replacement valve from them and they shipped the same day as the order and it arrived the next day, faster than I had expected. I viewed their video and it was very good at explaining what I had to do to replace the valve on my... Read more

Living in Texas it is hot all the time, even in fall, so our family loves our cold filtered water and ice. We woke up one morning with water all over the floor in the kitchen. It looked like it was coming from our freezer through the ice dispenser. We turned off the water shut off valve and removed what was now a giant block of ice instead of an ice dispenser from our freezer to melt in the sink. Since we have used AppliancePartsPros.com before, I knew exactly what I needed to do to see if we... Read more

• Leaking
• Not dispensing water

I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more

• Will not fill with water
• Leaking

Obtained part online from Appliance Parts Pros. com... within one or two days received the part... Replacing the defective part is straight forward... The valve is located on the left underside of the unit. Make sure the electrical power is off and the water supply to the unit is closed off. Disconnect the water inlet piping from the valve... in my case separating a 1/2 inch copper union. Remove the electrical quick connector from the solenoid prongs. The red wire is orientated at the top of... Read more

• Ice maker won't dispense ice
• Door sweating
• Frost buildup

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

• Ice maker not making ice
• Leaking

This was one of the easiest appliance repairs that I have ever done. I simply moved the refrigerator out of the cubby hole in which it resides, turned off the water supply at the wall, unplugged the electric cord, loosened the water supply line at the valve (had a water absorbent rag and small plastic bowl to catch what drained from the line), place it in the bowl and moved it aside. The valve was easily accessible and two screws detached it from the edge of the refrigerator box. Once loose, I... Read more

My frig is a year and a half old, Frigidaire with french doors and freezer drawer. It has an upper ice maker for the door in the frig and a bottom ice maker in the freezer drawer. After noticing the flood, I shut off the water supply to the frig and cleaned up the mess. Didn't know if it was the water solenoid valve that stuck open or if the bottom ice maker got stuck calling for water. This frig has 4 solenoid valves and according to the schematic, two valves are active any time water is... Read more

• Leaking

Replaced both inlet valves, no joy. Upon further inspection, found ice maker harness extremely tight at lower freezer door hinge, clamped in place right at a pivot point. Essentially the harness is held in place and rotates with the door. 6 wires broken inside. Splice repair and ice maker now works. Most likely will have to replace harness eventually. Unless there is more slack inside the freezer door this will probably happen again. Very poor design. Read more

• Not dispensing water
• Ice maker dispenses too much ice
• Ice maker not making ice
• Leaking

Replaced the water inlet valve assembly. That reduced the leakage to a smaller amount but did not fully stop the leakage. Replaced the ice maker assembly and that completed the repair. No leakage issues and ice maker is working with no issues. Read more

• Not dispensing water
• Leaking
• Ice maker not making ice
• Ice maker won't dispense ice

To verify if you have a bad valve in the first place read on... I first pulled out the ice maker to remove all the frozen water including the inlet section which was a huge solid waterfall of ice. While it was out completely disconnected I cleaned/chipped out the freezer section ice puddle. I also completely melted the ice cubes and ice puddles off the ice maker at the fill bucket end in the sink with running water careful to not get water near the power cord area. I then put a tall plastic cup... Read more

• Not dispensing water

Replaced the water inlet valve on the back of the refrigerator. Read more

Replaced the water line and water supply solenoid valve (slight weeping at valve body also). This is a 3 year old whirlpool refrigerator, model WRX988SIBM00. A crack in the water line after only 3 years is a poor design. My intent was to replace the entire water line from the valve to the filter. But I could not remove the interior top trim piece to access the filter connection. I did not want to force the trim piece to hard and break it. So what I did was install a new water line at the... Read more

• Leaking
• Ice maker not making ice
• Ice maker won't dispense ice

I replaced the water inlet valve. The toughest part was closing off the feed line while I waited for the valve to be delivered. The needle valve used to install the feed line wouldn't close completely. I ended up fabricating a plug from some parts from the hardware store. The mounting bracket on the new valve was completely different from the original, but it still mounted easily enough. The 1/4" plastic hose fitting was a different type from the original, but the hose fitted into it easily... Read more

Replaced both inlet valves, no joy. Upon further inspection, found ice maker harness extremely tight at lower freezer door hinge, clamped in place right at a pivot point. Essentially the harness is held in place and rotates with the door. 6 wires broken inside. Splice repair and ice maker now works. Most likely will have to replace harness eventually. Unless there is more slack inside the freezer door this will probably happen again. Very poor design. Read more