Frigidaire K-Cup Pad Post Pin Cogged Parts

• Leaking

The dishwasher is 4 years old, so I figured since it was leaking from the bottom, replacing the Tub Gasket PN: AP5690109, Splash Shield Kit PN: AP4338941 , and the bottom Door Seal/Gasket PN: AP5809675 was a good idea; the machine probably has around 1200 cycles in 4 years. There's no telling how much the door had opened and closed!? The bottom Door Seal/Gasket was badly worn, and the entire job took me around 30 minutes which included the detailed cleaning of the mating flanges. Take your... Read more

The dishwasher is 4 years old, so I figured since it was leaking from the bottom, replacing the Tub Gasket PN: AP5690109, Splash Shield Kit PN: AP4338941 , and the bottom Door Seal/Gasket PN: AP5809675 was a good idea; the machine probably has around 1200 cycles in 4 years. There's no telling how much the door had opened and closed!? The bottom Door Seal/Gasket was badly worn, and the entire job took me around 30 minutes which included the detailed cleaning of the mating flanges. Take your... Read more

A quick google search lead me to the problem - the plastic door gasket had become loose and broken. Received the part very quickly and installed it that night after a little trial and error. What the videos don't tell you is that to properly 'seat' the gasket you need to angle it UP when you push it into the little gap. If you angle it up, it will catch and seat properly, if you just push it in normally, it won't catch on the right part and it'll just hang loose at the bottom of the door and... Read more

The dishwasher is 4 years old, so I figured since it was leaking from the bottom, replacing the Tub Gasket PN: AP5690109, Splash Shield Kit PN: AP4338941 , and the bottom Door Seal/Gasket PN: AP5809675 was a good idea; the machine probably has around 1200 cycles in 4 years. There's no telling how much the door had opened and closed!? The bottom Door Seal/Gasket was badly worn, and the entire job took me around 30 minutes which included the detailed cleaning of the mating flanges. Take your... Read more

I went to appliancepartspros.com and searched "dishwasher rack rollers" and found mine immediately using only the make of the machine. It took me another 5 minutes to order the parts and check out. I received the parts in two days using the most economical shipping method. It took less than ten minutes to make my dishwasher as good as new! A very simple job made more simple by using appliancepartspro.com. Read more

• Not dispensing water

Parts where perfect. piece of cake.my wife was very impressed. Read more

Shopped online and found your great website, read reviews and based diagnostics on similarities I saw in other peoples stories. So I was able to choose correctly when replacing the circuit board. As far as the water switch in door, and drawer parts I just replaced them because I was tired of gluing them, and knew that with everything working good again and looking good, that it would be like a Tune up for our refrigerator. Read more

The part just snaps on the basket. You have to remove the clips on the end of the runner arms to be able to remove the basket. Once it was out the old arm snap off and you snap on the new arm. Only problem was my old arm was fine and I wished the company would just sell the gasket. It seems a waste to have to purchase the whole arm. The complete job took me about 10 minutes from start to finish. I ordered the part online a Sunday afternoon and it arrived at my house on Tuesday. Read more

Heater coil metal tabs inside the dishwasher rusted out . Replace Coil and both brass nuts . Done Read more

First i called sears parts direct to order this part, because that is where i purchased my electric range. they had an outrageous price of $98. unbelievable to think that such a small piece of rubber could cost that much. i also called a few other parts dealers on other websites. they also had high prices. when i called appliance parts pros they cut the cost by 50%. i am not sure if i could have found a better price because i stopped there. it is exhausting and time consuming to have to compare... Read more

The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

• Marks left on clothes
• Noisy

I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more

I ordered the parts and replaced them with new ones. Read more

Replaced the upper spray arm tube with a new one. Also replaced delivery tube grommet and the delivery tube gasket. Now everything works fine and no more leaks. Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more