Parts for Whirlpool LG7011XSW0: 03 - Cabinet Parts

Replacement screw for washers. Used to secure various components including handles, panels, and internal parts. Order if original is missing or stripped.

Size: 10-32 x 1/2 inch.

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

Grey rubber bumper for washers. Replaces worn, cracked, or missing bumpers that cushion the drum or cabinet. Installs on various washer models.

Exterior cover that restores your dryer's finished appearance and shields internal components. Replace if cracked, broken, or missing to maintain protection.

Black screw that secures the refrigerator side trim or finish panel. Replace if screw is missing, stripped, or damaged to restore a snug fit and clean look.

Dryer won't start when door closes? A broken door switch lever prevents the dryer from detecting a closed door. Easy 10-minute DIY fix with video.

Washer won't start or stops mid-cycle when door opens? The door switch detects door position for safe operation. DIY repair in 10-20 minutes with video.

Mounting screw for dryer assembly and panel attachment. Replace if screw is stripped, missing, or damaged during disassembly. Secures components.

This kit secures the lower toe/kick panel to the front of the appliance, keeping the panel tight and properly aligned. Replacing worn or missing clips restores a secure fit and makes access for service straightforward.

• Holds the toe/kick panel in place at the base of the cabinet
• Helps prevent panel rattling, gaps, or a loose/hinging lower panel
• Common fix when the lower panel won't stay secured after service
• Durable metal clip design for repeated panel removal and reattachment

• Unplug appliance before servicing; wear gloves to avoid sharp edges
• Support the toe panel while releasing old clips to prevent bending
• Install clips in the cabinet slots first, then engage the panel into the clips
• Verify the panel is fully seated on both sides before restoring power

Adjustable leveling foot that screws into the bottom of your dryer cabinet. Replace missing, broken, or cracked feet to stabilize and level your unit.

U-type clip nut slides onto sheet metal panels to create threaded anchor points for screws. Replace if broken, missing, or worn during repairs.

If your dryer door won't latch or the dryer won't start when you close the door, this top lock secures the cabinet during cycles. Easy 30-minute fix.

Includes two bumpers and two locking clips for securing dryer panels. Replace if clips are broken or missing to prevent rattling. Confirm fit with your model.

Dryer door won't close or stay latched? This door latch kit restores secure closure. Easy 15-minute DIY repair with common tools. Video guide included.

Hex head screw for trash compactor assembly. Replaces lost, stripped, or damaged screws during repairs. Essential hardware for securing components.

Retaining clip secures panels and assemblies in dishwashers, dryers, and laundry centers. Replaces worn, broken, or missing clips to restore fit.

For R/H hinge use 687905

(for the L/H hinge use 687905

Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.

Dryer door won't close or stay latched? This door latch kit restores secure closure. Easy 15-minute DIY repair with common tools. Video guide included.

Plastic handle that mounts to the front of your dryer door. Replace if cracked, broken, yellowed, or missing due to wear, impact, or age.

Replaces worn dryer front bearing and seal that cause squealing or scraping noise. Essential for smooth drum rotation. Confirm fit with your model.

Vinyl door seal lines the dryer door perimeter to block air leaks and cushion closure. Replace when worn or cracked to restore a tight seal. Verify fit by model.

Connects your dryer to the wall outlet to supply household electricity. Replace a damaged, frayed, or overheated cord to restore safe power connection.

Secures the door hinge in place for smooth opening and closing. Replace this small retaining clip if worn, broken, or missing to restore proper alignment.

This part has been discontinued and is no longer available.

Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.

Idler pulley maintains belt tension in your dryer drum assembly. Replace if the wheel is cracked, bracket is broken, or pulley has worn bearings.

Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.

Why this belt?

• Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
• Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
• Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.

Fixes these common dryer problems

DIY install — about 15 minutes

1. Unplug dryer; remove lint screen housing & front panel.
2. Release belt tension at idler pulley; lift drum slightly to slide old belt off.
3. Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
4. Re-assemble, run test cycle - enjoy quiet, consistent tumbling.

Fix excessive dryer noise or vibration with a new motor base. This support bracket secures the motor assembly for stable alignment and quiet operation.

Replacement machine bolt for securing panels, brackets, and components in dishwashers, dryers, washers, and laundry centers. Restores fit if missing.

Connects the dryer motor shaft to the drum belt. Replace if cracked, broken, or worn. Includes mounting hardware for secure motor-to-belt connection.

Dryer won't start or stops mid-cycle? A worn drive motor is often the cause. This motor turns the drum and circulates air. Moderate DIY repair.

Dryer won't start or stops mid-cycle? A worn drive motor is often the cause. This motor turns the drum and circulates air. Moderate DIY repair.

If your dryer motor has come loose or makes grinding noises, this motor clamp secures the drive motor. Simple DIY repair with basic tools in under an hour.

Secures hoses to prevent leaks in your washer. Replace if loose, cracked, or causing water leakage. Verify compatibility with your model number.

Converting your dryer from natural gas to propane? This LP conversion kit includes orifices and regulator parts. DIY-friendly with video, 1 hour.

Dryer won't heat or pilot lights but shuts off? This gas valve assembly controls burner ignition and flame. Typical DIY repair in 45-60 minutes.

Dryer not heating or won't dry clothes? This igniter kit lights the gas burner. Moderately easy DIY repair with video guide—replaces failed igniters.

Replacement mounting screw for securing panels, brackets, and interior assemblies. Needed when original screw is stripped, missing, or damaged.

Dryer won't heat or flame shuts off after 15 seconds? Gas valve coils control gas flow to the burner. Takes about 30 minutes to replace both coils.

Dryer won't heat or flame shuts off after 15 seconds? Gas valve coils control gas flow to the burner. Takes about 30 minutes to replace both coils.

8-32 mounting screw for dryer assemblies. Replaces lost, stripped, or damaged screws during repairs or panel reinstallation. Essential hardware part.

Mounting bracket for dryer shunt assembly. Secures electrical shunt component to cabinet frame. Replace if cracked, bent, or missing hardware slots.

Dryer won't heat or ignites inconsistently? Faulty wire harness between gas valve and igniter disrupts ignition signals. Simple connector replacement.

If your dryer won't stay lit or shuts off after a few minutes, the gas limiter may be faulty. This regulator controls safe gas flow to the burner.

Dryer making high-pitched sound when igniter turns on? This natural gas regulator maintains proper gas pressure to burners. DIY-friendly repair.

Spring installs inside the gas pressure regulator assembly on gas dryers. Replace if lost during conversion between natural gas and propane fuel types.

Seals unused pipe openings in your washer to prevent leaks and debris entry. Replace if damaged, cracked, or leaking to restore watertight closure.