Gasket & Seal

Note: The part is approximately 3" in diameter.

This refrigerator door gasket seals the door to the cabinet to keep cold air in and humid air out. Replacing a worn gasket restores a tight seal, helps maintain temperature, and reduces frost and energy loss.

• Forms an air-tight perimeter seal between the door and cabinet
• Helps maintain stable interior temperature and humidity
• Reduces frost, condensation, and air leaks
• Resolves: torn or deformed gasket, door not sealing or popping open, moisture around the door, excessive frost or longer run times

• Disconnect power before servicing
• Warm the new gasket to relax folds; use warm water or low heat to ease installation
• Remove the old gasket from the retainer; if screws are present, loosen to replace; seat corners first and press the bead fully into the channel
• After installation, check for uniform contact around the seal; close the door to help the gasket set and adjust door alignment if needed

This refrigerator door gasket seals the fresh food compartment door to restore an airtight closure. A proper seal helps keep cold air in, limit moisture intrusion, and support stable temperatures and efficiency.

• Creates a tight seal between the fresh food door and cabinet
• Helps maintain interior temperature and reduce energy loss
• Limits condensation and frost near the door opening
• Worn, torn, or misshapen gaskets may cause warm spots, sweating, or doors that won't close fully

• Unplug the refrigerator before servicing.
• Pull the inner lip from the door retainer to remove; some models require loosening liner screws hidden under the gasket edge.
• Warm the new gasket (warm water or gentle heat) to relax folds, then press the lip fully into the channel.
• Close the door and check for uniform contact; adjust hinges or re-tighten liner screws as needed.

This seal kit restores a proper water-tight barrier in the washer's drive area to prevent leaks and protect bearings and motor components on 1992-and-newer units.

• Seals the drive shaft/tub interface to stop water migration
• Helps prevent bearing and motor damage from moisture
• Common leak symptoms: water under the washer, rust streaks at center post, noisy spin from moisture intrusion
• May also address oil/water contamination around the transmission area

• Disconnect power and water; move the washer to a stable, level work area
• Removal of agitator, inner tub, and drive components is typically required
• Inspect shaft and mating surfaces; clean and lightly lubricate as specified by service literature
• Use proper drivers/press tools; do not hammer seals into place

The gasket is an OEM part for Whirlpool refrigerators. It is a sealing gasket responsible for creating an airtight seal between the refrigerator door and frame. This helps maintain proper temperatures inside the refrigerator and freezer compartments. 

Symptoms of a bad gasket include:

• Inability to maintain proper interior temperatures 
• Frost or condensation buildup inside the refrigerator or around doors and frames
• Higher electric bills from the compressor running excessively
• Noticeable temperature fluctuations when opening and closing the door

Causes of a bad gasket can include shrinkage and cracks due to aging, as well as tears, breaks, or holes from repeated use and compression. Over time, seals may no longer fully adhere, allowing air and warmer temperatures to enter.

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This door seal fits into the dishwasher's tub channel around the door opening. It compresses when the door closes to contain wash water and steam, helping prevent front-door leaks and maintain quiet, efficient operation. What it does:

• Creates a watertight seal between the dishwasher door and tub during cycles
• Helps keep water and steam from escaping; reduces operational noise
• Wear may show as drips at the door, moisture on the floor, or visible cracks/flattening
• Contributes to the door not sealing evenly

• 1 door seal

• Disconnect power and turn off the water supply before service
• Open the door, pull the old seal straight out of the channel, and clean the groove
• Warm and straighten the new seal; start at the top center and press evenly into the channel without stretching
• Close the door to help seat the seal and check for leaks on the next cycle

This is a dispenser inlet gasket intended for use on washing machines. This part ensures that the hot and cold water lines do not leak at the point where they are connected to the appliance. If the washing machine is leaking, the gasket may need to be replaced.Replacing a dispenser inlet gasket in a washing machine can be done easily. Screwdrivers and pliers are required. Disconnect the appliance before starting the repair. Wear work gloves for safety. The hot and cold water lines should both be turned off and removed to prevent flooding.This dispenser inlet gasket is an authentic OEM replacement part. It is sourced from the manufacturer. The replacement component is made of high-quality materials. It can be installed in several different models of washing machines. The dispenser inlet gasket is compatible with appliances produced by Frigidaire, Gibson, Electrolux, Westinghouse, and Kelvinator brands.

This high-temperature gasket seals the oven door to the cabinet. Replacing a worn seal helps your oven preheat more efficiently, hold steady temperatures, and reduces heat and vapor escaping around the door edge.

• Maintains a tight seal between the door and oven cavity to retain heat
• Supports accurate, consistent baking and roasting temperatures
• Helps reduce longer preheat or cook times caused by heat loss
• Replaces seals that are torn, brittle, flattened, or frayed

• Disconnect power and allow the oven to cool completely before servicing
• Open the door and remove the old gasket, noting clip/screw locations and orientation
• Clean the mounting channel; press the new gasket in place without stretching it
• After installing, preheat and check for even contact all around the door

This gray door gasket restores a tight seal around the freezer door opening so cold air stays in and warm, humid air stays out—helping maintain proper temperature and reduce frost buildup when the original seal is worn or damaged. What it does:

• Seals the perimeter of the freezer door to prevent air leaks
• Helps minimize frost/ice accumulation and moisture around the door
• Supports consistent interior temperatures and performance
• Common signs of failure: tears, warping, gaps, frost buildup, sweating/condensation, and poor door sealing

• 1 gray door gasket

• Unplug the appliance before servicing
• Warm the new gasket (soak in warm water or gently heat) to relax folds for easier installation
• Install starting at the corners; ensure the gasket fully seats in the retainer all the way around
• After installation, check seal tension around the door; use low heat to help the gasket conform if needed

Kitchen Aid blender dome and blade seal. Color: black. It measures about 3 inches in diameter.

Restore a reliable door seal with this refrigerator door gasket. It forms an airtight barrier between the door and cabinet to keep cold air in, reduce frost and condensation, and help your unit maintain stable temperatures.

• Seals the full door perimeter to prevent warm, humid air from entering the compartment
• Helps maintain consistent cooling performance and moisture control
• A worn, torn, or deformed gasket may cause temperature swings, frost/ice buildup, or moisture around the door
• Visible gaps, a door that won't stay closed, or a failed "paper test" indicate a failed seal

• Unplug the appliance before starting
• Let the new gasket relax flat; gently warm with a hair dryer on low or place in warm water to remove kinks
• Fully seat the gasket lip into the door channel/retainer, working evenly around all four sides and corners
• After installation, check the seal with a paper strip and fine-tune by gently warming and reshaping as needed

The Refrigerator Door Gasket is an OEM part for Whirlpool refrigerators. This gasket forms a seal around the refrigerator door, ensuring that cold air stays inside and warm air remains outside, maintaining the appliance's efficiency and keeping food fresh.

Causes of a bad door gasket can include regular wear and tear, mold or mildew buildup, and physical damage from repeated opening and closing of the door. 

Symptoms of a bad refrigerator door gasket include:

• Warm air entering the refrigerator, causing it to run more frequently
• Condensation or frost buildup inside the refrigerator
• Difficulty keeping the door closed
• Visible cracks, tears, or deformation in the gasket

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Grey

The Fresh Food Door Gasket is an OEM part for Whirlpool refrigerators. It is a replaceable sealing strip located around the fresh food compartment door that helps maintain cool temperatures inside.

Causes of a bad gasket can include breakdowns in the adhesive over time allowing air gaps, or physical damage such as cracks or punctures compromising the seal. 

Symptoms of a faulty gasket include:

• Frost or moisture condensation building up inside  
• Higher energy bills from the compressor running excessively
• Warm air freely entering/exiting around the perimeter 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This silicone gasket creates a flexible, heat-resistant seal in range and oven assemblies. Replacing a deteriorated seal helps contain heat and moisture at joints and trim areas, protecting internal components and restoring proper fitment.

• Forms a durable, high-temperature seal between designated mating surfaces
• Helps prevent heat, steam, odors, and spills from escaping at seams
• Can help address visible gaps, leaks at edges, or looseness around trim/panels
• Restores the manufacturer-specified seal after service on affected components

• Disconnect power and allow the appliance to cool; turn off gas if applicable
• Remove old gasket/sealant and clean surfaces thoroughly; dry completely
• Position/install exactly as directed for your model; avoid stretching or over-compressing
• Follow model/service instructions for any required cure or set time before heating

This freezer door gasket forms the airtight seal between the door and cabinet. Replacing a worn gasket restores a proper seal, helping maintain temperature and reducing frost and moisture for more reliable freezer performance.

• Creates the perimeter seal to keep cold air in and humid air out
• Helps prevent frost/ice buildup and temperature swings inside the freezer
• Supports smooth door closing and even contact around the frame
• Common symptoms: tears, cracks, warping, gaps, persistent frost, or warm spots

• Unplug the appliance before servicing
• Warm/relax the new gasket in hot water or with a hair dryer on low to improve fit
• Start at a corner and press the gasket lip fully into the retainer channel; ensure corners seat first
• Check the seal with a paper test and gently reshape as needed; allow time for the gasket to conform

This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:

• Forms a tight barrier between components to contain fluids and prevent leaks
• Helps maintain proper pressure/flow at the sealed joint
• Reduces risk of moisture damage around the connection point
• Common signs it's worn: drips or puddles, dampness around the joint, musty odors, visible cracking or flattening of the old seal

• 1 seal

• Disconnect power and shut off water or gas supplies before servicing
• Access the sealed joint; remove the old seal and clean mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved lubricant; install without twisting
• Reassemble, restore utilities, and check closely for leaks during initial operation