Parts for Lg WM3477HS: Other Parts

This duct outlet directs a dryer's exhaust from the cabinet to the external vent, helping maintain proper airflow and reduce leaks. It replaces a damaged or worn outlet flange to restore safe venting. What it does:

• Channels dryer exhaust from the cabinet to the vent hose or duct
• Helps maintain proper airflow for efficient drying
• Prevents exhaust leaks that can cause poor performance or odors
• Reduces rubbing/interference that can create noise when damaged

• One duct outlet

• Disconnect power before servicing; for gas dryers, turn off the gas supply and disconnect per local codes
• Use basic hand tools; avoid bending the outlet flange to prevent cracks
• Verify a secure seal with the vent hose after installation and test operation

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

The Shipping Bolt Assembly is an OEM part for LG washing machines. This assembly is used to secure the washer drum during transportation, preventing it from moving and getting damaged. Shipping bolts are essential for maintaining the integrity of the washing machine when it is being moved or installed.

Causes of a bad or missing shipping bolt assembly include improper handling during moves, wear and tear from multiple uses, or not reinstalling them when relocating the washer. Ensuring that the shipping bolts are in place is crucial for protecting the internal components of the washer during transit.

Symptoms of a missing or damaged shipping bolt assembly include:

• Excessive movement or shaking of the drum during transportation
• Internal components of the washer getting damaged during a move
• Difficulty in securing the drum for transport
• Noise or instability during washer installation

This OEM LG part is also compatible with Sears/Kenmore.

This outer tub assembly is the main watertight housing that supports the washer drum and contains wash water. Replacing a damaged outer tub restores the washer's ability to hold water and properly support the rotating drum. What it does

• Holds and seals wash water inside the washer to prevent leaks.
• Supports the inner drum and bearings for smooth rotation.
• Helps maintain correct alignment between the drum and motor/drive components.
• Often replaced when cracks, distortion, or corrosion cause leaks or unusual noise.

• One outer tub assembly.

• Disconnect power and water supply before beginning service.
• Replacing the outer tub typically requires removing panels, the inner drum, and drive components; have the correct tools and a service manual for your model.
• Inspect and replace related seals, gaskets, bearings, and fasteners as needed.

The Tub Ball Bearing is an OEM replacement part forLG washing machines. This crucial component supports the inner tub or drum, allowing smooth rotation during the wash and spin cycles.

Symptoms of needing to replace the tub ball bearing include:

• Excessive noise or grinding sounds during operation
• Vibration or shaking of the washing machine
• Difficulty in the tub or drum rotating or spinning

Causes of a faulty tub ball bearing can include normal wear and tear over time, exposure to excessive loads or unbalanced loads, or physical damage due to impact or mishandling.

This OEM LG part is also compatible with select Kenmore washer models.

The Motor Rotor Bolt is an OEM part for LG washing machines. It secures the rotor to the motor shaft, playing a crucial role in the efficient functioning of the motor and ensuring the washer drum spins correctly during wash cycles.

Causes of a bad motor rotor bolt can include wear and tear from prolonged use, corrosion due to exposure to moisture, or damage from over-tightening or accidental impacts. A faulty motor rotor bolt can compromise the stability of the motor, leading to various operational issues.

Symptoms of a bad motor rotor bolt include:

• The washer drum not spinning or spinning irregularly
• Unusual noises during operation, such as banging or clunking
• The washer failing to complete cycles or stopping mid-cycle
• Visible wear or damage to the bolt or surrounding components

This OEM LG part is also compatible with Sears/Kenmore models.

The Tub Seal Gasket is an OEM part for LG washing machines. It creates a tight seal between the inner and outer tubs during the wash cycle, preventing leaks and containing water. The gasket helps prevent water from escaping the tub. 

Causes of a bad gasket can include wear and tear from repeated use over time, exposure to cleaning chemicals or extreme temperatures, or damage from handling heavy loads. 

Symptoms of a bad gasket include: 

• Water leaking from the outer tub during operation
• Excessive moisture in areas surrounding the washer 
• The tub making creaking or grinding noises
• Decreased washing or spinning performance

This OEM LG part can also be used on Kenmore/Sears appliances. 

This clamp assembly secures a hose, tube, or similar connection inside your appliance, maintaining a tight, reliable hold to prevent leaks and movement. Replacing a worn or damaged clamp restores proper sealing and dependable performance.

• Holds a hose/tube or component firmly in place to help prevent leaks or disconnections
• Reduces movement and vibration that can cause noise or wear
• Restores clamping force when the original is bent, corroded, or stretched
• Common symptoms: drips at a joint, hose slipping off, rattling, or a missing/broken clamp

• Disconnect power; shut off the water supply if the clamp secures a water line
• Place a towel or pan to catch residual water and relieve line pressure if applicable
• Note the original orientation; use suitable hand tools to release and seat the clamp securely
• Inspect the hose/tube and fitting for damage; replace if cracked or deformed and check for leaks after reassembly

This multi-connector wiring harness routes power and signals between components to restore electrical connections in the appliance. It replaces a damaged or worn harness to help re-establish reliable component communication and operation. What it does:

• Provides multiple pre-terminated connectors to link control boards, sensors, motors or other modules
• Replaces frayed, burned or broken wiring that can cause intermittent operation or component failures
• Restores proper electrical pathways so affected circuits can function normally
• Helps correct symptoms such as no-start, erratic cycles, or loss of specific functions tied to a failed harness

• One multi-connector wiring harness as shown

• Disconnect power before starting any repair to avoid shock or short circuits
• Match connector shapes and wire colors; do not force connectors together
• Inspect mating connectors and terminals for damage and clean before connecting
• Secure harness to prevent rubbing or pinching during operation

This replacement refrigerator door gasket seals the door to keep cold air inside, helping restore proper cooling and reduce frost, condensation, and energy loss from a damaged or worn seal. What it does:

• Creates an airtight seal around the refrigerator door to maintain internal temperature.
• Prevents warm air infiltration that can cause frost buildup and uneven cooling.
• Reduces condensation and helps improve compressor efficiency when sealing properly.
• Common symptoms of a failing gasket: visible cracks or gaps, cold air leaks, frost or moisture buildup, and higher energy use.

• Remove the old gasket and clean the door flange before installing the new seal.
• Press the gasket evenly into the door channel; some models use retaining clips or screws—model-specific instructions.
• Check that the gasket seats uniformly with the door closed and make minor adjustments as needed.

This is a motor harness intended for use with washing machines. The motor harness is a wiring component that's attached to the washing machine's motor and is used to conduct electricity between the motor and the PCB. Wear and tear, damage, or other issues can arise with the motor harness over time. When there is a malfunction or failure with this component, a replacement part is necessary to continue the appliance's efficient and safe use.Signs that something has gone wrong with the washing machine's motor harness include intermittent operations or a device that won't run at all. Replacing the motor harness is a relatively easy task. Disconnect the appliance from power and wear work gloves for safety. Ensure all connections between the motor and motor harness are secure before plugging the washing machine back into to avoid the motor's accidental activation.This motor harness is an authentic OEM replacement part. It is sold as an individual unit. The motor harness is made of high-quality, durable materials. It comes sourced directly from the manufacturer to ensure compatibility. The motor harness can be installed in various models of washing machines. It fits correctly into appliances produced by Kenmore and LG.

This door inner frame is the replacement inner panel frame that supports the door liner and trim, restoring proper fit and appearance. It helps keep the door assembly aligned and finished for normal operation and seal integrity. What it does:

• Provides structural support for the door liner and attached trim pieces
• Restores correct alignment and fit of the door assembly
• Helps maintain a proper door seal and reduces drafts or uneven closing
• Replaces cracked, warped, or cosmetically damaged inner door framing

• One door inner frame

• Disconnect power to the appliance before starting any door repair
• Removal typically requires taking off door trim and inner liner; keep fasteners organized
• Inspect door gasket, hinges, and hardware while replacing the frame; replace any damaged hardware

This replacement door handle restores a secure, comfortable grip for opening and closing the appliance door. Replace a cracked, loose, or missing handle to bring back proper function and a clean, finished look. What it does:

• Provides the handhold used to open and close the door
• Mounts to the door with internal screws or bolts specific to the model
• Restores appearance after wear, cracks, or finish damage
• Typical symptoms: cracked/broken or wobbly/loose handle, missing handle, difficulty gripping

• 1 handle

• Disconnect power to the appliance before servicing; allow surfaces to cool
• Access the handle's mounting screws from the inner side of the door; remove trim or panels as needed
• Transfer any spacers or bushings from the old handle to the new one
• Tighten hardware evenly without overtightening; verify door opens and closes smoothly

The Door Latch Hook is an OEM replacement part for LG front load washers. It is a component of the overall latch and locking assembly and works to securely close and lock the washer door. With a properly functioning latch hook, the washer door remains tightly sealed during cycles to ensure optimal water retention and the most thorough cleaning. 

Symptoms of a bad door latch hook include:

• Water leaks around the door during washing cycles
• The door fails to latch fully and unlock after cycles 
• Difficulty opening or closing the washer door completely
• Alignment issues like misaligned or skewed door positions

Causes of a bad door latch hook can include wear over extended use. Damage may also result from washing hard or abrasive items that put excess strain on the latch mechanism over time.

This OEM LG part is compatible with Sears/Kenmore front-load washer models as well. 

This is the refrigerator's water inlet valve assembly. It controls and directs household water into the dispenser and ice maker as needed, restoring proper water flow and ice production.

• Opens to supply water to the ice maker and dispenser when energized
• A common fix for no/low water at the dispenser
• Can resolve no ice production due to no water fill
• May address leaks or continuous dripping from the dispenser/ice maker
• Failure can present as buzzing or clicking with little/no water flow

• Disconnect power and shut off the water supply before servicing
• Have a towel or small container ready to catch residual water
• Note hose and wire locations or take photos before removal
• After installation, restore water and power, then check for leaks and run a test fill

The Water Inlet Valve Assembly is an OEM replacement part for LG washing machines, designed to control the flow of water into the laundry tub. This part is responsible for opening and closing to allow water into the wash drum at the appropriate times during the wash cycle, providing the correct water level and temperature.

Causes of a bad Water Inlet Valve Assembly can include mineral deposits blocking the valve, electrical failure preventing the valve from opening or closing properly, or physical damage to the valve mechanism itself.

Symptoms of a bad Water Inlet Valve Assembly include:

• Inadequate filling of the washer drum
• Water entering the drum when the washer is off
• Unusual noises during the fill cycle
• Water that is too hot or too cold, indicating a failure in valve operation that controls temperature

This OEM LG part can also be used on Kenmore/Sears appliances. 

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

This control panel assembly replaces a worn, cracked, or non-responsive user interface to restore cycle selection and display functions. It provides the buttons and display needed to send commands to the appliance for normal operation. What it does

• Houses the touchbuttons/keys and display used to select cycles, options, and start or stop the appliance.
• Sends user commands to the main control board via ribbon cable or connector.
• Common symptom fix: unresponsive or stuck buttons, faded or cracked button pad, or missing/blank display indicators.
• Restores visible cycle/status indicators and tactile button response when original panel is faulty.

• One complete control panel assembly

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Requires removal of top/console trim and careful disconnect of ribbon cable(s) and wire harness—handle connectors gently.
• Keep small screws and trim in a safe place; alignment tabs must seat fully when reinstalling.

This Thermostat Assembly monitors and regulates internal temperature within the appliance's heating circuit. Replacing a failed thermostat restores proper heat control, helps prevent overheating, and can resolve common heating performance issues so cycles run correctly. What it does

• Senses internal temperature and opens/closes the heater circuit to maintain proper heat
• Provides over-temperature protection by cutting power at unsafe temperatures
• Helps ensure consistent heating performance throughout the cycle
• Helps with symptoms such as no heat, overheating/shutting off, or unusually long cycle times

• 1 thermostat assembly

• Disconnect power before servicing; allow hot components to cool
• Access the thermostat location (varies by model); note wire positions before removal
• Mount flush to the surface for accurate sensing; transfer original hardware if required
• After installation, test operation; use a multimeter for continuity checks if needed

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

Restore stable, level support with this replacement leg assembly. The adjustable foot steadies the unit on uneven floors, reducing vibration and rattling while allowing precise leveling for proper alignment and smooth, reliable operation.

• Provides adjustable support at the base of the unit
• Helps keep the appliance level on uneven or sloped floors
• Reduces wobble, vibration, and rattling noises
• Promotes proper door alignment and closure
• Replaces stripped, cracked, or missing leg assemblies

• Disconnect power; shut off water supply if applicable
• Carefully tilt and support the appliance to access the leg area
• Unthread the old leg; hand-thread the new assembly to avoid cross-threading, then fine-adjust with a wrench
• Level front-to-back and side-to-side; confirm stability before use

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

This wire harness routes power and signals between the washer's control and multiple components. Replace a damaged harness to restore dependable operation when wiring is cut, brittle, or connectors are heat-damaged or corroded.

• Distributes electrical power and communication between the control board and components such as the motor, pump, valves, door lock, and sensors
• Maintains safe, reliable connections when insulation and terminals are intact
• Typical failure signs: intermittent operation, no start, specific loads not working (pump/motor/valves), or error codes traced to wiring faults
• Visible damage like chafed wires, broken connector locks, or burned/corroded terminals indicates replacement

• Disconnect power and turn off water supply before servicing; wear cut-resistant gloves
• Photograph and label connectors; move one plug at a time from old to new to avoid miswiring
• Route along original clips, channels, and grommets; keep wiring clear of sharp edges and moving parts
• Ensure all connectors are fully seated; test operation before final reassembly

This accessory assembly is a genuine replacement component that restores the appliance's accessory fit and function. It installs in the accessory area to secure and connect related parts for reliable operation. What it does:

• Replaces a damaged or missing accessory assembly to restore proper attachment and alignment
• Secures accessory components so controls and moving parts operate smoothly
• Commonly used when accessories are loose, broken, or no longer seating correctly
• Helps prevent rattling, misalignment, or intermittent accessory-related issues

• Disconnect power (and water, if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance's service manual for exact steps
• Keep fasteners and small parts organized during removal and reassembly

This heater assembly restores consistent, controlled heat inside your appliance so cycles reach the correct temperature. Replacing a failed heating element assembly helps resolve no-heat complaints and performance issues that leave loads cold or extend run times.

• Generates the heat required during the appliance's heating phases so temperatures rise as intended
• Works with thermostats/sensors to achieve and maintain target temperature
• Typical symptoms: no heat, lukewarm operation, unusually long cycles, or heating-related error codes
• Often confirmed by an open element or out-of-range resistance in continuity tests

• Disconnect power and allow the appliance to cool completely before servicing
• Access the heater per the service documentation; photograph wiring and routing to aid reassembly
• Handle the element carefully to avoid bending or damaging coils; transfer any brackets/sensors from the original if they are not supplied with the new part
• After installation, inspect and clear airflow or circulation paths and verify correct voltage before test operation

This inlet hose connects your appliance to the household water supply, delivering water where needed and helping prevent leaks at the connection. Use it to restore reliable water fill and flow. What it does:

• Transfers cold (or cold/hot where applicable) water from the household supply to the appliance
• Provides a sealed connection at the inlet to prevent drips and leaks
• Restores normal water fill when a cracked or blocked hose is causing no/low fill
• Helps correct intermittent filling or water pressure issues caused by damaged hoses

• Turn off the home's water supply and unplug the appliance before replacing the hose
• Inspect the hose ends and gaskets; replace gaskets if worn to ensure a watertight seal
• Hand-tighten fittings, then give a firm quarter-turn with a wrench; do not overtighten
• After installation, restore water and power, then check connections for leaks during an initial fill cycle

The Drain Pump and Motor is an original LG (OEM) replacement part for LG made washing machines that is responsible for removing water from the washer at the end of the wash cycle. The pump forces water out through the drain hose so that clothing comes out free of excess water, making the drying process faster. 

Symptoms of a failing Drain Pump Motor include:

• Water not draining out of the washing machine 
• Noisy or unusual sounds coming from the pump area during the drain cycle
• The washing machine stopping mid-cycle

Causes of a bad Drain Pump Motor can range from obstructions in the pump or hose, which can strain or damage the motor, to wear and tear from regular use leading to motor failure. Electrical issues can also affect the motor's performance, preventing it from operating correctly.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Drain Pump Assembly is an OEM part for LG washing machines. This part removes water from the washer's tub during the drain cycle.  

Causes of a bad drain pump assembly can include blockages from debris or small clothing items, wear and tear on the pump motor, or damage to the pump's impeller.  

Symptoms of a bad drain pump assembly include:

• Water not draining from the washer
• Loud or unusual noises during the drain cycle
• Error codes related to drainage issues
• Water leaking from the pump area

This OEM LG part is also compatible with some Kenmore models.

AC pump motor assembly replaces a failed pump drive to restore proper water removal. Direct-fit replacement restores pump operation to stop standing water, noisy pumping, or continuous filling issues in compatible LG machines. What it does:

• Drives the washer/dishwasher pump to move water out of the tub or through the circulation system.
• Restores proper drainage when a worn motor causes the unit to fail to pump water.
• Stops humming, grinding, or high-pitched noises caused by a failing pump motor.
• Helps prevent leaks or overflow caused by a non-operating pump (when pump seals and hoses are intact).

• Always unplug the appliance and shut off water supply before starting repairs.
• Access the pump from the front/bottom service panel; support the tub or cabinet as needed to avoid strain.
• Keep original wiring orientation and mounting hardware; transfer gaskets/seals or replace if damaged.
• After installation, run a test drain cycle to ensure proper operation before full reassembly.

The Pump Filter Assembly is an OEM replacement part for LG washing machines. It is a crucial component that filters out lint, debris, and other particles from the wash water, preventing them from recirculating and damaging the pump or other internal components.

Symptoms of a need to replace the pump filter assembly:

• Clogging or blockages, leading to poor drainage or water not draining completely
• Excessive buildup of lint, hair, or other debris in the filter screen
• Leaks or water seeping from the filter housing or surrounding area
•  Unusual noises or vibrations during the drain or spin cycles, indicating a potential blockage

Causes of a faulty pump filter assembly can include excessive lint accumulation, damage to the filter screen or housing due to impact or mishandling, and general wear and tear over time.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

This rotor position sensor (Hall sensor) tracks the direct-drive motor's rotor position and speed so the control can commutate the washer motor accurately. Replacing a failed sensor can restore proper wash/agitate and spin performance. What it does:

• Detects rotor position and speed from the stator assembly
• Sends timing feedback to the control for correct motor start, direction, and speed
• Supports smooth agitation and spin ramp-up/ramp-down
• Failure may cause: no spin or agitation, cycle stalling/pausing, or an LE motor error code

• 1 rotor position sensor assembly

• Unplug the washer and shut off water; wear protective gloves
• Access the motor at the rear of the tub; remove the back panel if needed
• Remove the rotor and stator; support the stator to protect wiring, then unclip/unscrew and replace the sensor
• Align the sensor correctly and seat the connector fully before reassembly and testing

This rotor assembly is the rotating half of your washer's direct-drive motor. It mounts to the rear of the tub and, working with the stator, spins the drum for wash and spin cycles to restore smooth operation.

• Couples with the stator to drive the inner tub during wash and spin
• Helps resolve no- or slow-spin complaints
• Can address a drum that won't turn or turns intermittently
• May reduce grinding/clicking from the rear caused by damaged rotor magnets

• Unplug the washer and turn off water supply before servicing
• Access from the rear; remove the center bolt and pull the rotor straight off the shaft
• Magnets are strong—keep fingers clear; align splines/keyway on reinstallation
• Tighten the center bolt securely and inspect the stator and sensor while open

This hinge spring restores proper tension to the door so it opens and closes smoothly and stays aligned. Replacing a fatigued spring helps prevent sagging or slamming and supports a consistent, reliable door close.

• Provides the return tension/counterbalance for the door hinge mechanism
• Assists smooth opening/closing and helps the door stay properly aligned when latched
• Helps maintain consistent closing force over time
• Failure symptoms include: door drops quickly, won't stay aligned or fully closed, weak/squeaking spring action

• Disconnect power before service; allow any hot surfaces to cool
• The hinge and spring are under tension—support the door and release/install tension carefully
• Note spring orientation and hole positions before removal; match them on installation
• Access may require removing trim or the door; keep fasteners organized for reassembly

This pressure switch assembly monitors the washer's tub water level and signals the control to fill, drain, and advance cycles properly. Replacing a faulty switch restores accurate water level sensing for reliable washing performance.

• Senses air pressure from the tub to determine water level
• Helps prevent overfilling and underfilling
• Common failure symptoms: overfills or won't fill, won't advance to spin/drain, drains continuously, or shows a PE (water level sensor) error
• Can cause intermittent cycle stops when readings are inaccurate

• Disconnect power and turn off water supply before servicing
• Access is typically from the top/console area; note hose and connector positions
• Inspect/clear the pressure hose; ensure it's not cracked, kinked, or blocked
• Seat the hose fully on the barb and reconnect the wire harness securely; test a fill cycle for proper operation

The Suspension Spring Holder is an OEM part for LG washing machines. This holder supports the suspension springs that help stabilize the washer drum during operation, reducing vibration and movement. It plays a critical role in ensuring smooth and quiet operation of the washing machine.

Over time, the suspension spring holder can become worn or damaged due to regular use, heavy loads, or accidental impacts. Causes of a bad suspension spring holder include wear and tear, physical damage, or corrosion from moisture exposure.

Symptoms of a bad suspension spring holder include:

• Excessive vibration or shaking during wash cycles
• Unusual noises, such as banging or clunking
• The washer drum appearing misaligned or sagging
• The washing machine moving or walking during operation

This OEM LG part is also compatible with Sears/Kenmore.

The Pump Hose is an OEM replacement part for LG washing machines. It is a flexible tube that connects the pump assembly to the internal tub and spins through the detergent dispenser area. The pump hose is responsible for circulating and removing water during the wash and rinse cycles. 

Symptoms of a bad pump hose include:

• Leaks or water not fully draining from the washer 
• Slow or inefficient filling and draining of water  
• Pump running loudly or continuously
• Wet areas under or around the washer

Causes of failure can be cracks or splits developing in the tubing from repeated bending and flexing over time, or blockages restricting water flow.

It is also compatible with some Kenmore models.

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

The Washer Door Lock Switch is an OEM part for LG washing machines. This critical safety feature locks the washer door during operation to prevent it from being opened, which ensures safety and proper functioning. The door lock switch also communicates with the washer's control system to indicate that the door is securely closed and the machine can begin its cycle.

Symptoms of a bad Washer Door Lock Switch include:

• The washing machine refusing to start, despite the door appearing to be closed.
• The door failing to lock properly, or the lock releasing prematurely during a cycle.
• Error messages on the washer's display related to door closure issues.

Causes of a bad door lock switch can include mechanical failures such as worn or damaged locking mechanisms, electrical issues like faulty wiring or failed solenoids, or alignment problems that prevent the door from engaging the switch properly.

This OEM LG part is also compatible with Sears/Kenmore models.

This clamp assembly secures a hose or tubing connection to maintain a watertight seal and reduce vibration. Replacing a worn or damaged clamp helps stop leaks and prevents hoses from slipping loose during operation. What it does:

• Holds a hose or tube firmly in place to maintain proper sealing at the connection point.
• Prevents leaks caused by loose, cracked or corroded clamps.
• Reduces vibration and rattling from unsecured hoses.
• Common symptom: visible leaking, water pooling, or a loose hose connection.

• Disconnect power and shut off water supply before starting any repair.
• Use the correct pliers or screwdriver for the clamp type; avoid damaging the hose.
• Inspect the mating hose and seal; replace any cracked or hardened hoses before reinstalling.
• Do not overtighten—tighten just enough to secure the hose without cutting or deforming it.

This Main PCB power control board assembly replaces the appliance's primary electronic control module to restore proper power distribution and command signals. It helps recover normal control operation and device responsiveness when the main board is faulty. What it does:

• Manages power distribution and control signals to the appliance's components
• Controls user-interface commands and cycle/function sequencing
• Can stop intermittent power, random resets, or unresponsive controls caused by a failing main board
• Works with the appliance's safety and sensor inputs to coordinate operation

• Disconnect power (unplug or switch off breaker) before removing or installing the board
• Handle the PCB by its edges and avoid static discharge; use an ESD strap if available
• Verify board part number matches the board being replaced before installation

This filter assembly replaces the water/ice filter housing and valve connections in compatible refrigerators to restore proper water flow to the dispenser and icemaker. It helps stop leaks and resolve low or no-water flow when the housing is faulty. What it does

• Replaces the internal filter housing and inlet/outlet connections that route water to the dispenser and icemaker.
• Restores normal water flow and pressure when a cracked or damaged housing causes leaks or restricted flow.
• Helps prevent leaks that can occur from worn seals or damaged fittings in the filter assembly area.
• Can resolve symptoms such as reduced dispenser flow, intermittent water flow to the icemaker, or visible leaks near the filter area.

• One filter assembly (housing and associated valve/connectors) as shown

• Turn off the refrigerator water supply and unplug the appliance before beginning work.
• Relieve system pressure by dispensing water after shutoff and have towels ready to catch residual water.
• Inspect and tighten all connections; replace any O-rings or seals if specified by OEM instructions.
• After installation, turn the water back on, check for leaks, and flush several liters through the dispenser per manufacturer guidance before use.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

The Gasket is an OEM part for LG washing machines. It forms a seal between the door and the drum, preventing water from leaking out during the wash cycle.

Causes of a bad gasket can include wear and tear over time, mold or mildew buildup, or physical damage from sharp objects or rough handling. Detergent residue and other factors can also degrade the gasket material.

Symptoms of a bad Gasket include:

• Water leaking from the washer door
• Visible tears, cracks, or deformities in the gasket
• Mold or unpleasant odors emanating from the gasket area
• The door not sealing properly, leading to inefficient washing

This OEM LG part is also compatible with Sears/Kenmore models.

This bellows is the flexible door boot seal that helps keep water contained in the washer tub and maintains a watertight seal around the front-load door. It replaces a damaged or leaking door boot to reduce leaks and restore proper sealing. What it does:

• Forms a flexible, watertight seal between the washer door and tub to help prevent leaks
• Keeps laundry water inside the drum during wash and rinse cycles
• Helps maintain drum pressure balance and proper door closing
• Commonly replaced when cracked, torn, or permanently deformed

• One bellows

• Recommended for front-load washers; fit with your model before ordering
• Typical replacement requires removing the outer and/or inner door trim and detaching clamp(s)
• Disconnect power and water supply before beginning any repair to avoid injury

Connector hose joins an appliance water line to internal plumbing, providing a sealed path for water. Replacing a damaged connector stops leaks and restores reliable water delivery to dispensers and ice makers.

• Joins and seals the appliance water line to the unit, preventing leaks and ensuring proper flow.
• Replace when you notice dripping, pooling under the appliance, or reduced water/ice production.
• Fits factory connection points for a secure, leak-resistant seal.
• Works with existing clamps and O-rings when those components are serviceable.

• Shut off the water supply and disconnect power before removing the old connector.
• Relieve water pressure by running the dispenser or dispensing water before disconnecting lines.
• Inspect and replace worn clamps or O-rings; hand-tighten fittings, then turn the water on slowly and check for leaks.

The Shock Absorber Kit is an OEM part for LG washing machines. This part minimizes vibrations and absorbs shocks during the washing and spinning cycles. By stabilizing the drum, these shock absorbers ensure smooth and quiet operation, preventing excessive movement and potential damage to the washer.

Causes of a bad shock absorber can include wear and tear over time, heavy or unbalanced loads that put extra strain on the absorbers, or damage from impact or mishandling. 

Symptoms of a bad shock absorber include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or knocking noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

This OEM LG part is also compatible with Sears/Kenmore.