Amana Dryer Parts

• Won't start
• Timer will not advance
• No heat or not enough heat
• Touchpad does not respond

I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad. As I had to make two orders paying shipping twice because I thought I found a bad part when testing the igniter but the thermal fuse was also bad and since in a different part of the machine I did not take the time to check it, bad mistake. Also one tool mentioned in the video... Read more

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• No heat or not enough heat
• Doesn't shut off
• Touchpad does not respond

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Too hot
• Timer will not advance
• Takes too long to dry
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Noisy

I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more

• No heat or not enough heat
• Takes too long to dry
• Too hot

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

• Timer will not advance
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

• Timer will not advance
• No heat or not enough heat
• Too hot
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

I bought the new arm assembly because after a few times of going in through the front of the machine and reaching in the back under the drum I could get to the pulley, so I took it off of the arm and lubed it and then replaced it back inside, put the belt back on and it was good for a week or so , then started squeaking again. So after doing this about 6 times I got the impression that is was the wheel and shaft on the arm were worn out causing the wheel to wobble and wear the arm. I then... Read more

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

• Will not tumble
• Takes too long to dry

I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more

• Too hot
• Shuts off too soon

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

• Will not tumble

It was the day of my birthday June 6th when my wife came to me to tell me that the dryer was not working. Immediately I started to look for a new dryer from Best Buy and the rest. Then I said It would be better if I waited for 4th of July at which time I could find a better deal. This is when I decided to take it apart to see what was wrong. Initially, I thought of the belt that could be broken and I rotated the drum by hand and I heard a noise of the belt at times falling on the drum. I was... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

I used the Appliance Parts Pros d.i.y. video to get some oversight on the repair; ordered the parts (heating element, Hi-Limit T-stat and Dryer Thermal Cut-Off kit). I unplugged the electric; disconnected the exhaust duct; moved the clothes dryer so that I could remove the back sheet metal panel. The electrical connection at the heater "Stacon" terminal was corroded and broken - an open circuit. This had happen about 10 years before and I was familiar with this problem. After removing the... Read more