Gasket & Seal

I took the new seal out of it's packaging and used a blowdryer on low heat to soften up the seal so that the crease from shipping (it was folded to ship) disappeared. Next I took the refrigerator door off, removed the old seal, & cleaned the area where the new seal would be applied. Following the video on the Appliance Pro Parts website, I re-installed the new seal and put the door back on. Last step was to snap on the new hinge cap I ordered. The video online was easy to follow and this... Read more

Ordered replacement door seals, assistance picking the seals and speed of shipping was excellent. The installation was about as easy a job as can be, remove old seals, clean the doors and press in the new seals. With that said, I don't believe these are the same quality as factory original seals, the doors do not close as positive as the original and I have an air leak in the freezer door seal allowing condensation and ice to form. Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

We replaced both the fresh food door and freezer door gaskets. Old gaskets must have lost their magnetic abilities. Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

• Door sweating

My co-worker bought a house to flip and gave me the refrigerator. I'd been looking for a garage refrigerator to store water, cola, etc in. Fridge was essentially fine but I sanded and painted one side which had rust spots. Turned out like new. The door seal was moldy and didn't seal properly. The only advice I can lend is to take the door off the hinges and lay it down flat. So much easier. With this seal you basically just take out all the screws, peel off old seal and set the new one... Read more

Removed front panel from refrigerator door and replaced the ice chute door seal and also replaced the seal inside the door that seals against the ice maker. Read more

Replace the boot seal assembly Read more

I simply pulled out the old gaskets starting in the corners and pressed in the new ones using my thumbs starting at the top and working down. Read more

I will say that the GE Washer/Dryer combo is nice if you need to save space, but trying to fix it was far from "fun". It took several hours to get to the location of the Seal Tub. First the dryer had to come off the top, then pretty much every bit of the internals needed to come out too, The seal could not be accessed from the bottom of the machine, and it wasn't easy to get to it from the top. If you have patience, and keep track of everything you did, so you can undo it, the project can be... Read more

Watched the first half of your online video and followed your steps. Easy video to follow. I had a newer model so there were a few adjustments, but it was very easy to follow. Read more

Purchased your parts watched the awesome video on your site. Repair was complete within an hour the dishwasher is running as I am typing this. Thank you so much for the service you offer. Regards, Rich Read more

Fairly simple fix. followed you tube video step by step..needed a set of extra hands (wife came in handy) when installing gasket..after several loads as a test, no leaks. Read more

I ordered the gasket with the model number off the frig. AppliancePartPros.com made it easy to find my part. There was also a "how to" video on the same page. I ordered the part and it got to OH the next day. Following the video guideline it took me 15 minutes to remove the door, strip out the old seal and put in the new one. I will be ordering all my appliance parts from AppliamcePartsPros.com Read more

Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,... Read more

Ordered the correct gasket, watched video and completed the repair myself. Wasn’t hard at all. Read more