General Electric Refrigerator Defrost Heater, Icing Kit, Fountain Heater

Defrost heater that melts frost from the evaporator coil so the refrigerator can maintain efficient cooling. Replacing a failed heater restores normal defrost cycles and helps prevent ice buildup that blocks airflow. What it does:

• Heats the evaporator coil during the defrost cycle to remove frost and ice buildup.
• Restores proper airflow and cooling when ice accumulation was restricting the evaporator.
• Common symptoms of a failing heater: visible frost or ice on the evaporator, freezer running warm, or extended run times.
• Works with the appliance's defrost thermostat and control to complete the defrost cycle.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Handle the heating element carefully; avoid bending or damaging the coil or terminals.
• Verify the part number matches your appliance before installation.
• If other defrost components (thermostat, control board, sensors) show signs of failure, inspect and replace them as needed.

This thaw heater is the evaporator defrost heating element that melts frost during the refrigerator's defrost cycle. Replacing a failed heater helps restore normal defrosting and reduce frost buildup that can restrict cooling. What it does:

• Heats the evaporator coil during the defrost cycle to melt accumulated ice
• Prevents excessive frost buildup that can block airflow and reduce cooling efficiency
• Common symptoms of a failing heater: heavy frost or ice on the evaporator/back wall, reduced cooling, or long compressor run times
• Works as part of the appliance's defrost system alongside the defrost thermostat and control

• Disconnect power to the appliance before starting any repair
• Access typically requires removing interior panels and the evaporator cover; handle the evaporator and wiring carefully
• Inspect associated defrost components (thermostat, timer/control) if problems persist; replace only parts confirmed faulty

The Defrost Heater Assembly is an OEM replacement part for GE refrigerators. It is designed to heat the evaporator coils during the defrost cycle, melting any accumulated ice or frost. This helps maintain proper airflow and prevents the coils from freezing over, allowing your refrigerator to cool normally.

A bad defrost heater assembly can occur due to electrical issues, component failure, or damage to the heater itself. If you notice symptoms such as excessive frost or ice buildup in the freezer, inconsistent cooling, or water pooling at the bottom of the refrigerator, it may indicate a need to replace the defrost heater assembly.

Symptoms of a bad defrost heater assembly include:

• Excessive frost or ice buildup in the freezer
• Inconsistent cooling
• Water pooling at the bottom of the refrigerator

Restore your refrigerator by replacing the faulty defrost heater assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This defrost heater melts frost and ice from the freezer evaporator so the refrigerator can maintain proper airflow and cooling. Replaces a failed heater to restore normal automatic defrost cycles and prevent excessive frost buildup. What it does:

• Gently heats the evaporator coils during the defrost cycle to remove accumulated ice.
• Helps restore normal airflow and temperature by preventing heavy frost or ice buildup.
• Commonly used when you see repeated frost on coils, ice on the evaporator, or poor cooling performance.
• Works with the existing defrost control/thermostat to run only during defrost cycles.

• One defrost heater assembly

• Disconnect power before accessing the evaporator compartment or any wiring.
• Install requires removing interior liners or evaporator cover—follow your model's service manual.
• Inspect and test the defrost thermostat and bi-metal or control board if the heater failed; replace as needed.
• Avoid touching the heater element or bending evaporator fins; handle components carefully.

This fixture heater is the heater assembly used to warm a targeted appliance component so the unit operates correctly and resists ice buildup. It restores heat where a small, localized heater is required. What it does

• Provides localized heat to a fixture or component to prevent freezing and help normal operation.
• Warms internal surfaces that can collect frost or condensation, reducing ice buildup.
• Restores heat when a failed heater causes intermittent or no warming at the fixture.
• Helps eliminate symptoms such as frost accumulation, poor component function, or temperature-related faults.

• One fixture heater assembly.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle terminals and wiring carefully; match wire connections and secure all fasteners.
• Use basic hand tools; for correct routing and placement.

This defrost heater for the freezer evaporator melts frost and ice buildup so the cooling system can run efficiently. It restores normal defrost cycles and helps prevent ice-clogged evaporators that reduce cooling performance. What it does:

• Warms the evaporator coil during defrost cycles to remove accumulated frost and ice
• Helps restore proper airflow and temperature control in the freezer compartment
• Commonly replaced when evaporator icing prevents the freezer from cooling properly
• Works with the defrost control and thermostat to complete timed defrost cycles

• One defrost heater assembly

• Disconnect power to the appliance before starting any repair
• Access typically requires removing evaporator cover panels inside the freezer; handle the evaporator fins and heater carefully to avoid damage
• Verify continuity of the heater with a multimeter before and after installation; replace related defrost components if they also test faulty

The Water Tank Heater is an OEM component for GE bottom-mount refrigerators offering internal water and ice dispensing. Located within the drinking water reservoir, it facilitates antibacterial heating cycles. Dependable water delivery relies on a functioning tank heater.

Symptoms of failure include:  

• Absence of hot water from the dispenser or ice maker
• Cloudy or sedimented water quality needs frequent filter changing  
• Mold or bacterial growth detected within the reservoir

Causes involve cracked or porous heater elements that cannot transfer thermal energy effectively over extended years, loose wiring terminals cutting off electric current, or mineral buildup hindering heat transfer to the surrounding tank.

Replacing with this genuine GE heater ensures optimized reservoir sanitization through precise temperature regulation. Compatible replacements include models for Hotpoint, RCA, and Kenmore side-by-side refrigerators seeking to restore hot water dispensing and purification features.
 

This heater fill tube assembly routes water into the appliance's heater area to ensure proper water flow and prevent contact with electrical components. It replaces damaged or worn tubes to help stop leaks and restore normal fill operation. What it does:

• Directs incoming water to the heater/tub area so the appliance can heat and circulate water correctly
• Shields the heating element and electrical connections from direct water exposure
• Common symptom fixes: visible leaks, water pooling, or interrupted fill cycles
• Helps prevent intermittent heating issues caused by improper water routing

• Disconnect power and shut off the water supply before beginning repair
• Verify correct orientation and seating of any seals, grommets or clamps during installation
• Handle clips and plastic fittings gently to avoid breakage; replace damaged fasteners as needed