Maytag Refrigerator Defrost Heater, Icing Kit, Fountain Heater

This evaporator defrost heater melts frost from the evaporator coil during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice buildup that restricts cooling and leads to warm spots. What it does:

• Heats the evaporator coil to clear frost/ice during defrost
• Helps maintain proper airflow between freezer and fresh food sections
• Typical symptoms: heavy frost on the back panel/evaporator, weak cooling or rising temperatures
• Also cause evaporator fan noise from ice contact and longer run times

• 1 evaporator defrost heater

• Disconnect power before servicing; allow any ice to thaw
• Access the heater behind the freezer's rear panel; avoid damaging fins or refrigerant lines
• Secure the heater and route wires exactly as original, keeping them clear of the fan and sharp edges
• Restore power and verify the defrost cycle per the service procedure

The defrost heater melts frost off the evaporator coil during the automatic defrost cycle so cold air can circulate freely. Replacing a failed heater helps clear recurring ice buildup and restores stable refrigerator and freezer temperatures.

• Heats the evaporator to remove frost/ice during the defrost cycle
• Prevents airflow blockages to maintain consistent cooling
• Common symptoms: heavy frost behind the rear panel, fan noise from ice contact, weak cooling or warm spots, ice returning soon after manual defrost
• When the heater is open/burned out, frost accumulates on the coil and restricts airflow

• Disconnect power before servicing; wear cut-resistant gloves
• Safely defrost any heavy ice; do not chip at coils to avoid fin or tubing damage
• Route and secure wiring as original; reuse existing clips/brackets as required and keep leads clear of the fan
• After reassembly, ensure panels seal properly and the defrost drain path is clear for meltwater

This radiant-style defrost heater melts frost from the evaporator during automatic defrost cycles. Replacing a failed heater restores airflow and helps maintain consistent temperatures while preventing ice buildup on the freezer back wall.

• Heats the evaporator coil to clear frost/ice during the defrost cycle
• Promotes proper airflow for stable cooling performance
• Common fix for heavy frost on the back freezer panel, warming in the fresh food section, or a noisy evaporator fan contacting ice
• If the element tests open (no continuity), the unit will not defrost

• Disconnect power before servicing; allow built-up ice to melt for safe access
• Access from the freezer by removing the rear panel; handle the glass-sheathed element carefully
• Note wire routing and transfer any reusable shields, clips, or insulation from the original part if present
• After replacement, verify the defrost thermostat/sensor and control initiate a defrost cycle

This is the electric heating element that warms the evaporator during defrost. It clears frost from the coils so air can circulate, helping restore proper cooling and consistent temperatures.

• Melts frost accumulation on the evaporator during the defrost cycle
• Helps resolve symptoms like frost buildup, weak airflow, warm fridge section, or frequent icing
• Supports stable temperatures and efficient cooling performance

• Unplug the appliance before service; allow ice to melt or carefully defrost as needed
• Access is typically from the freezer section behind the rear panel
• Handle the glass/metal element carefully; avoid bending or damaging terminals
• Verify correct routing and secure connections; do not overtighten mounting clips

This defrost heater warms the evaporator coil during the automatic defrost cycle to melt frost and clear airflow. Replacing a failed heater helps prevent ice buildup and restores more consistent cooling performance throughout the refrigerator. What it does

• Heats the evaporator during defrost cycles to melt accumulated frost
• Keeps airflow paths clear so temperatures stay stable
• Helps prevent frost-clogged coils that reduce cooling
• Common signs of failure: heavy frost on the back wall/evaporator cover, weak cooling, evaporator fan hitting ice, or ice returning soon after a manual defrost

• One defrost heater

• Disconnect power before servicing; wear cut-resistant gloves
• Access is behind the freezer's rear evaporator cover; remove shelves/bins and the panel
• Defrost heavy ice before removal to avoid damaging the coil or insulation
• Transfer any original mounting clips/insulators and route wires exactly like the original; avoid bending the heating element

The Heater is an OEM component specifically designed for Whirlpool bottom-mount refrigerators. Located within the fresh food compartment walls, it prevents condensation by maintaining warm air circulation along interior surfaces. 

Causes of a bad heater include deterioration of heating coils or electronic boards over many years, loose connections disrupting power delivery, or damage from moisture exposure.

Symptoms include:

• Foggy or frosted exterior walls need frequent drying  
• Puddles of water collecting beneath vegetable drawers
• Musty odors developing within refrigerator shelves

This OEM replacement is also compatible with Kenmore, KitchenAid, and some GE models.

This replacement heater restores proper heat output to the feature that uses it, helping your appliance reach and maintain temperature for consistent results. When the original heater fails open or shorts, related cycles may not heat or take much longer.

• Converts electrical energy into heat within the appliance's heating circuit
• Maintains target temperature during the selected function
• Common symptoms: no heat in the related feature, extended preheat/warm-up, uneven results, or heating-circuit error codes
• Visible signs can include breaks, burn spots, or an open element on continuity testing

• Disconnect power at the breaker or unplug before servicing; allow components to cool
• Note wire positions and fasteners for accurate reassembly; transfer any reusable clips/insulators
• Handle the element carefully—avoid bending or striking; make clean, tight electrical connections
• After installation, run a brief test cycle to ensure proper heating

This defrost heater assembly melts frost from the evaporator during the defrost cycle to keep air flowing and maintain consistent temperatures. Replacing a failed heater helps restore proper cooling performance and prevents excessive frost buildup.

• Heats the evaporator coil during defrost to clear ice and frost
• Helps resolve symptoms like heavy frost/ice on the evaporator, poor cooling, or warm fridge/cold freezer imbalance
• Can address frequent evaporator fan icing or blocked air passages

• Disconnect power before servicing; allow any ice to thaw safely
• Access is typically behind the rear panel of the freezer compartment
• Handle the heater and wiring carefully; avoid bending or stressing terminals
• Verify proper placement of any clips/shields and wiring connections match original

Radiant Glass (Quartz), Length (Approx) - 20-1/4, 450 watts

This radiant defrost heater melts ice build-up on the evaporator coil so your refrigerator can maintain proper airflow and cooling. It restores normal defrost operation and helps prevent excessive frost accumulation. What it does:

• Radiant heating element designed to melt frost and ice from the evaporator coil during the defrost cycle
• Restores airflow and consistent cooling when the evaporator has been restricted by ice
• Common symptom: visible frost or ice on evaporator or in freezer compartment
• Common symptom: poor or uneven cooling, longer run times, or a freezer that cycles abnormally

• One radiant defrost heater (single unit as shown)

• Disconnect power to the appliance before servicing to avoid shock risk
• Access typically requires removing the evaporator cover; handle evaporator fins and heater carefully
• Inspect defrost thermostat/thermistor and defrost control components while replacing the heater — replace only the failed components

This fill tube heater keeps the ice maker's water inlet from freezing so your refrigerator can produce ice reliably. It applies gentle heat around the fill tube to help prevent ice blockages and water drips in the freezer.

• Warms the ice maker fill tube to help prevent freezing and ice buildup
• Helps maintain consistent water flow into the ice maker during fill
• Can address symptoms like no ice production, small/hollow cubes, or a frozen fill tube
• Reduces leaks at the fill spout caused by ice blockage

• Unplug the refrigerator and turn off the water supply before servicing.
• Defrost any ice in the fill tube area; avoid sharp tools that can puncture plastic.
• Route and secure the heater along the fill tube as originally installed; avoid pinching wires.
• Ensure the electrical connector is fully seated, then restore power and verify ice maker operation.

This 12-inch defrost heater melts frost and ice from the evaporator so your refrigerator can run efficiently and keep food at the proper temperature. It replaces a failed heater to restore normal automatic defrost cycles. What it does:

• Warms the evaporator coils during the defrost cycle to remove frost and ice buildup
• Helps prevent reduced cooling and frost accumulation on the evaporator
• Commonly used when the freezer/back wall has visible ice or when defrost cycles fail
• Works with the fridge's existing defrost control/timer and thermostat to clear ice safely

• One 12-inch defrost heater

• Disconnect power to the appliance before starting any repairs
• Access usually requires removal of the evaporator cover; handle the evaporator and wiring carefully
• Verify correct heater orientation and secure connections; do not force or kink the element

This heater and thermostat assembly replaces the dryer's heating module to restore normal drying performance by regulating and producing heat. It's a direct-fit assembly designed to simplify replacement and reduce diagnosis time. What it does:

• Provides the dryer's primary heating element and temperature control components.
• Regulates operating temperature via built-in thermostats/thermal cutouts.
• Stops heating when a thermostat or thermal cutoff opens, which can cause no-heat or under-heating symptoms.
• Helps address common symptoms like no heat, long dry times, or intermittent heating when diagnosed to this assembly.

• Disconnect power to the appliance before starting service to avoid shock or injury.
• Carefully discharge any residual heat and avoid contact with sharp sheet metal and the heating element.
• Inspect and replace any blown thermal fuses or damaged wiring.
• Follow model-specific instructions and torque/electrical guidelines from the OEM during installation.

This assembly contains the evaporator defrost heater and temperature thermostat that remove frost from the evaporator coil to help restore normal cooling. Replaces failed defrost components to help the fridge complete defrost cycles and reduce ice buildup. What it does:

• Heats the evaporator during defrost cycles so accumulated frost melts away
• Uses a temperature thermostat to open/close the heater circuit at the correct temperature
• Commonly replaces failed defrost parts when frost builds on the evaporator or the refrigerator runs continuously
• Helps restore normal airflow and cooling when defrost cycle has stopped functioning

• One defrost heater and thermostat assembly

• Disconnect power to the appliance before starting any repair
• Handle the evaporator and fins carefully to avoid damage; keep electrical connections secure and dry
• Follow the manufacturer instructions for routing and mounting the assembly

Radiant Glass (Quartz), Length (Approx) - 17-3/4, 400 watts

This heater assembly provides the high heat source used to dry clothes faster by warming the air inside the dryer. It replaces a failed or damaged heating element to restore normal drying performance and temperature. What it does:

• Generates the heated air needed for effective drying
• Commonly replaced when dryer produces little or no heat
• Can cause tripped thermal cutoff or heating-circuit issues when failed

• One heater (heating element) assembly as shown

• Disconnect power before starting; this part involves live-voltage components
• Inspect associated thermostats, fuses, and wiring; replace faulty safety parts as required
• Handle the element carefully — edges may be sharp and terminals can be damaged by rough handling