Appliance Parts

• Won't start
• Timer will not advance
• No heat or not enough heat
• Touchpad does not respond

I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad. As I had to make two orders paying shipping twice because I thought I found a bad part when testing the igniter but the thermal fuse was also bad and since in a different part of the machine I did not take the time to check it, bad mistake. Also one tool mentioned in the video... Read more

The repair kit has everything needed for both sides of the rack but there were no instructions so it took me some time to figure out how it all mounted on the basket. The original design was totally different than the repair kit so it would have been very beneficial to have at least a diagram that showed how everything fit together. That being said, once I figured out how all the parts fit, then it was a very easy repair. You won't reuse any of the old parts except for the end caps that snap... Read more

• Will not tumble
• Noisy

Our Whirlpool Duet Sport Dryer, 6.7 cu. ft, Model WED8300SW0, bought new 8 years ago (2006), developed a VERY loud squeaking noise inside the dryer. Removing the top panel did not isolate the problem. I researched the problem and through the videos appearing on Appliance Parts Pros (APP) website and a few others, determined that the problem was either the drum belt, one or more of the 4 drum support rollers, or idler pulley or any combination of these. I ordered the kit to allow for... Read more

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• No heat or not enough heat
• Doesn't shut off
• Touchpad does not respond

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

It took no time to find where the problem was! I got my Frigidaire model number and got on-line with AppliancePartsPros.com where I have gone for over a decade for all my household repairs. Why? because they are honest, helpful, considerate, fast, and its easy to locate and SEE the exact part I need. 10 minutes after the burning of my element, one was in my cart and ordered! Done. TWO days later, the part arrived. I turned off the circuit breaker, unscrewed the two 1/4" screws and pulled off... Read more

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more

• Too hot
• Timer will not advance
• Takes too long to dry
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Noisy

I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

• No heat or not enough heat
• Takes too long to dry
• Too hot

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

• Timer will not advance
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

• Leaking
• Ice maker not making ice
• Not dispensing water
• Ice maker won't dispense ice

On your chat box with Kelsey, I decided it was probably the valve and so ordered a water valve. It came next day! Before trying to install it, I wanted to confirm whether it was the valve or the icemaker, so I chatted again with Kelsey who gave me a useful test (manually pour water into the icemaker) that confirmed the icemaker was functional. So I thought it surely is the valve, so I removed the old valve according to the very helpful video on your website. When I opened the box with the new... Read more

I ordered 4 of this part from AppliancePartsPros.com and watched the repair video of the product. This was a simple repair that took 10 minutes to replace all 4 wheel units on the bottom rack. Product is exact match to the part I replaced. Read more

• Will not tumble
• No heat or not enough heat

I was out of the country when the damage occurred but based on my wife's description I knew what had happened. Upon returning to the 1st World, i verified a totally free-spinning drum and ordered a full rebuild kit (rollers, belt & idler). The instruction video was very helpful - especially in listing every single tool needed so i only made one trip to the workshop and brought up exactly what i needed, the first time. Everything went pretty much according to the instructions except that... Read more

First, I did a search based on the problem I had with my model of dryer. The model number was on the door frame and was visible when I opened the dryer door. The problem was, when I pressed the button to start a dryer cycle, I heard a clicking noise and the indicator text changed to "Drying", but I could not hear or see the dryer drum turning. The search led me to a page that indicated my problem was usually one of 3 common causes. 1. Faulty door switch 2. Broken Drum drive belt 3. burned out... Read more