Kenmore / Sears Dryer Parts

• Won't start
• Timer will not advance
• No heat or not enough heat
• Touchpad does not respond

I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad. As I had to make two orders paying shipping twice because I thought I found a bad part when testing the igniter but the thermal fuse was also bad and since in a different part of the machine I did not take the time to check it, bad mistake. Also one tool mentioned in the video... Read more

• Will not tumble
• Noisy

Our Whirlpool Duet Sport Dryer, 6.7 cu. ft, Model WED8300SW0, bought new 8 years ago (2006), developed a VERY loud squeaking noise inside the dryer. Removing the top panel did not isolate the problem. I researched the problem and through the videos appearing on Appliance Parts Pros (APP) website and a few others, determined that the problem was either the drum belt, one or more of the 4 drum support rollers, or idler pulley or any combination of these. I ordered the kit to allow for... Read more

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• No heat or not enough heat
• Doesn't shut off
• Touchpad does not respond

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Too hot
• Timer will not advance
• Takes too long to dry
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Noisy

I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more

• No heat or not enough heat
• Takes too long to dry
• Too hot

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

• Timer will not advance
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

• Will not tumble
• No heat or not enough heat

I was out of the country when the damage occurred but based on my wife's description I knew what had happened. Upon returning to the 1st World, i verified a totally free-spinning drum and ordered a full rebuild kit (rollers, belt & idler). The instruction video was very helpful - especially in listing every single tool needed so i only made one trip to the workshop and brought up exactly what i needed, the first time. Everything went pretty much according to the instructions except that... Read more

Watched video. Took dryer apart to get to heating element and sensors. In process found alot of lint had escaped into inner dryer and had a thick coating over heating element. I cleaned out most lint and pulled apart lint trap on front and cleaned out as much accumulated lint as possible. I then removed the heating element (very simple, three screws in a support bracket) and found it was broke in one spot.(wire - element severed). I believe the heavy lint build up on elements caused lint to... Read more

First, I did a search based on the problem I had with my model of dryer. The model number was on the door frame and was visible when I opened the dryer door. The problem was, when I pressed the button to start a dryer cycle, I heard a clicking noise and the indicator text changed to "Drying", but I could not hear or see the dryer drum turning. The search led me to a page that indicated my problem was usually one of 3 common causes. 1. Faulty door switch 2. Broken Drum drive belt 3. burned out... Read more

• Timer will not advance
• No heat or not enough heat
• Too hot
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

I bought the new arm assembly because after a few times of going in through the front of the machine and reaching in the back under the drum I could get to the pulley, so I took it off of the arm and lubed it and then replaced it back inside, put the belt back on and it was good for a week or so , then started squeaking again. So after doing this about 6 times I got the impression that is was the wheel and shaft on the arm were worn out causing the wheel to wobble and wear the arm. I then... Read more

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more

We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more