Parts for Kenmore 796.41682610 (79641682610, 796 41682610): Other Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

The Shipping Bolt is an OEM part for LG washing machines, designed to secure the washing machine's drum during transportation. These bolts are important for preventing damage to the drum and suspension system by immobilizing the drum, thereby avoiding any excessive movement or vibrations that could occur while moving the appliance. 

Causes of a bad shipping bolt can include improper removal during installation, damage from handling, or degradation over time if it was left in place during operation. A damaged or missing shipping bolt can lead to issues with the washing machine's drum alignment and overall stability.

Symptoms that indicate the shipping bolts need removal or installation include:

• Excessive noise or vibrations during operation, suggesting the bolts were not removed after installation.
• Damage to the washing machine's drum or suspension system after moving the appliance without the bolts properly installed.

This OEM LG part can also be used on Kenmore/Sears appliances. 

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

This lifter is a replacement drawer support that helps hold and guide a refrigerator/freezer drawer for smooth, even operation. Restores proper alignment and reduces sticking or uneven movement. What it does:

• Supports and stabilizes a sliding drawer so it opens and closes smoothly
• Helps maintain proper drawer alignment and load distribution
• Worn or broken lifters can cause sagging, binding, or uneven drawer movement
• Replaces damaged or missing lifter hardware to restore normal drawer function

• Disconnect power and empty the drawer before starting any repair
• Remove the drawer or access panel per your model's service instructions to reach the lifter
• Install the new lifter in the same orientation and secure any retaining clips or screws; do not force parts into place
• If fasteners or adjacent guides are damaged, replace them as well for a secure fit

This door hinge bracket mounts the hinge to the washer's front cabinet, keeping the door aligned so it closes and seals properly. A bent or broken bracket can lead to door sagging, poor latching, or leaks at the door.

• Secures the door hinge to the washer's front panel/cabinet
• Supports door weight to maintain alignment
• Helps preserve proper door-to-gasket contact for sealing
• Typical symptoms: door sags or rubs, won't close/latch, or water leaks at the door

• Disconnect power and shut off water before servicing.
• Support the door before removing hinge/bracket screws to prevent strain.
• Transfer the hinge to the new bracket and reinstall using existing hardware.
• Align the door and ensure latch engagement and gasket seal before fully tightening.

Customized machine screw for select washers that fastens specific assemblies and resists vibration. Replace a missing, stripped, or damaged factory screw to restore a solid, rattle-free fit and proper component alignment.

• Secures designated brackets, panels, or housings per the manufacturer's specifications
• Maintains alignment and stability under high-speed spin and vibration
• Replaces missing, corroded, or stripped hardware to stop looseness and noise
• Use when the original screw is worn, damaged, or lost

• Unplug the appliance and shut off water before servicing
• Support the component while removing/installing screws
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep screws organized—lengths and styles may vary by location

The Motor Rotor Bolt is an OEM part for LG washing machines. It secures the rotor to the motor shaft, playing a crucial role in the efficient functioning of the motor and ensuring the washer drum spins correctly during wash cycles.

Causes of a bad motor rotor bolt can include wear and tear from prolonged use, corrosion due to exposure to moisture, or damage from over-tightening or accidental impacts. A faulty motor rotor bolt can compromise the stability of the motor, leading to various operational issues.

Symptoms of a bad motor rotor bolt include:

• The washer drum not spinning or spinning irregularly
• Unusual noises during operation, such as banging or clunking
• The washer failing to complete cycles or stopping mid-cycle
• Visible wear or damage to the bolt or surrounding components

This OEM LG part is also compatible with Sears/Kenmore models.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

The Outer Door Boot Seal Clamp is an OEM part for LG washing machines. This clamp secures the outer door boot seal, ensuring a tight seal to prevent water leaks during the wash cycle.

You should replace the outer door boot seal clamp if it becomes damaged or loses its tension, which can happen due to regular use, exposure to harsh cleaning agents, or physical wear and tear.

Symptoms of a bad outer door boot seal clamp include:

• Water leaks from the door area during the wash cycle
• Loose or shifting door boot seal
• Difficulty in closing the washing machine door securely

This OEM LG part is also compatible with Sears/Kenmore.

This balance weight secures to the appliance frame to add counterweight where needed, helping reduce vibration and stabilize moving parts for quieter, more reliable operation. What it does:

• Adds counterbalance to a drum, door or other moving component to reduce shaking and excessive movement during operation.
• Restores proper weight distribution to prevent off-balance conditions that can trigger vibration or noise.
• Typically fastens to the frame with mounting bolts to transfer and even out dynamic loads.
• A worn, loose or missing balance weight may be linked to loud banging, heavy vibration or uneven operation.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove the appropriate access panels to reach the mounting location; keep fasteners for reassembly.
• Reinstall using the original mounting bolts and follow OEM torque recommendations when available.
• Inspect adjacent suspension, mounts and hardware while servicing.

This outer tub cover protects the washer's drum assembly and helps keep water and components contained during operation. It replaces a worn or damaged cover to restore proper sealing and prevent leaks or debris intrusion. What it does:

• Covers and protects the washer tub and internal components from water, lint, and foreign objects.
• Helps maintain proper alignment and sealing of the tub during wash cycles.
• Commonly replaced for visible damage, cracks, or when leaks appear around the tub area.
• Supports stable drum operation by keeping internal components enclosed.

• Disconnect power and turn off water supply before starting any repairs.
• Installation may require removing the cabinet or drum assembly; follow the service manual for step-by-step guidance.
• Handle the cover carefully to avoid scratching or bending mounting tabs.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

The Outer Tub Gasket is an OEM replacement part for LG front-load washers. Situated between the front and rear outer tubs, it forms a critical seal preventing water leaks during fills and cycles. Constructed from durable yet flexible rubberized material, this gasket withstands constant compression from tub movements.

Causes for replacement are cracks developing from years of flexing stresses, as well as distortions that compromise sealing integrity. Normal seal compression can also cause gradual wear of sealing material over time.

Symptoms of a faulty front-load outer tub gasket include:

• Puddles or drips of water between or behind the wash tubs
• Dried mineral deposits from leakages around tub connection points

This OEM LG part is also compatible with some Sears/Kenmore.

Washer screw

This is a motor harness intended for use with washing machines. The motor harness is a wiring component that's attached to the washing machine's motor and is used to conduct electricity between the motor and the PCB. Wear and tear, damage, or other issues can arise with the motor harness over time. When there is a malfunction or failure with this component, a replacement part is necessary to continue the appliance's efficient and safe use.Signs that something has gone wrong with the washing machine's motor harness include intermittent operations or a device that won't run at all. Replacing the motor harness is a relatively easy task. Disconnect the appliance from power and wear work gloves for safety. Ensure all connections between the motor and motor harness are secure before plugging the washing machine back into to avoid the motor's accidental activation.This motor harness is an authentic OEM replacement part. It is sold as an individual unit. The motor harness is made of high-quality, durable materials. It comes sourced directly from the manufacturer to ensure compatibility. The motor harness can be installed in various models of washing machines. It fits correctly into appliances produced by Kenmore and LG.

This Outer Door Frame restores the exterior trim on a refrigerator door, replacing cracked, dented or worn frames to improve appearance and door alignment. Fits where the door's outer cabinet trim is damaged or missing. What it does

• Replaces the exterior trim piece that surrounds the refrigerator door, restoring a finished look.
• Helps maintain proper door alignment and clearance by providing the intended edge profile.
• Covers and protects underlying door components from bumps and wear.
• Useful when the existing frame is cracked, warped, dented or cosmetically damaged.

• One outer door frame

• Disconnect power to the appliance before beginning work to avoid electrical hazard.
• Remove door trim pieces and handles as needed; keep fasteners for reassembly.
• Handle edges and any attached glass or plastic panels carefully to avoid breakage—use two people for larger doors.
• If the frame secures to clips or adhesive, follow OEM instructions and replace any damaged clips or seals.

This inner door frame replaces the interior trim that secures the microwave door components and restores a finished appearance. It helps ensure the door closes cleanly and keeps internal door parts properly aligned for safe operation. What it does:

• Replaces a cracked, warped, or dented inner door frame that can allow rattling or misalignment
• Provides the mounting surface and support for inner door components and insulating layers
• Helps restore a flush door fit and reduce air/gap issues that cause improper sealing
• Reduces visible damage and improves the oven's cosmetic appearance

• One inner door frame

• Disconnect power (unplug or switch off circuit breaker) before servicing the door to avoid electrical shock
• Remove the outer door panel and inner components carefully; keep fasteners and insulating layers in order
• Handle glass and painted surfaces carefully to avoid breakage or scratches

This locker hook engages the appliance's latch/lock mechanism to keep the door securely closed during operation. Replacing a worn or bent hook restores reliable latching and helps prevent nuisance door/lock errors and cycle interruptions.

• Interfaces with the door lock/latch to secure the door during use
• Allows the safety interlock to confirm the door is closed
• Common symptoms: door won't latch or stay closed, needing to hold/push door to start, door/lock error messages
• Physical signs of failure: bent hook, worn contact surface, or cracked/broken mounting ears

• Disconnect power; turn off water supply if applicable
• Access the hook location on the door or cabinet/tub (varies by model); remove mounting screws/clips
• Transfer any reusable hardware; align the new hook so it mates cleanly with the latch/lock and tighten fasteners
• Close the door to verify smooth engagement before running a cycle

The Magnetic Door Plunger is an OEM part for LG washing machines. It is designed to securely hold the door in a closed position during the operation cycle, employing a magnet mechanism for enhanced reliability. The plunger ensures that the door latch is properly engaged, preventing the machine from running if the door is not closed correctly.

Causes of a bad Magnetic Door Plunger can include wear and tear from constant use, failure of the magnetic mechanism due to exposure to moisture or mechanical damage, or a misalignment that prevents the door from closing properly.

Symptoms of a bad Magnetic Door Plunger include:

• The washing machine door not staying closed during cycles.
• The machine failing to start due to a door sensor not detecting closure.
• Random pausing of the machine during operation if the door unlatches.

This OEM LG part is also compatible with Sears/Kenmore.

This water inlet valve assembly regulates the flow of household water into the washer's dispenser and tub. Replacing a sticking or leaking valve restores proper filling during wash and rinse cycles and helps prevent unwanted drips or overfilling. What it does

• Opens and closes electronically to allow water into the machine as commanded by the control
• Directs water through the dispenser for detergent and softener flushing and into the drum
• Typical symptoms of a failed valve include no fill, slow fill, continuous filling, or water seeping into the tub when the washer is off
• Also presents external leaks at the valve body or hose connections

• 1 inlet valve assembly

• Unplug the washer and turn off both water supply valves before starting
• Relieve line pressure and have towels or a shallow pan ready to catch water
• Label or photograph hose and wire locations for accurate reassembly; transfer any mounting hardware from the original if needed
• After installation, reopen water supplies and check all connections for leaks; run a test fill cycle

The Water Inlet Valve Assembly is an OEM replacement part for LG washing machines, designed to control the flow of water into the laundry tub. This part is responsible for opening and closing to allow water into the wash drum at the appropriate times during the wash cycle, providing the correct water level and temperature.

Causes of a bad Water Inlet Valve Assembly can include mineral deposits blocking the valve, electrical failure preventing the valve from opening or closing properly, or physical damage to the valve mechanism itself.

Symptoms of a bad Water Inlet Valve Assembly include:

• Inadequate filling of the washer drum
• Water entering the drum when the washer is off
• Unusual noises during the fill cycle
• Water that is too hot or too cold, indicating a failure in valve operation that controls temperature

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Water Inlet Valve Filter Screen is an OEM part for LG washing machines. This filter screen is designed to fit inside the water inlet valve, ensuring that debris and sediment are filtered out before the water enters the washing machine. This helps maintain clean water flow and protects the internal components of the washing machine from damage caused by particles.

Causes of a bad Water Inlet Valve Filter Screen can include clogging due to sediment buildup, damage from high water pressure, or wear and tear over time. Regular inspection and cleaning can help prolong the life of the filter screen.

Symptoms of a bad Water Inlet Valve Filter Screen include:

• Reduced water flow into the washing machine
• Long fill times or failure to fill
• Sediment or debris found in the wash water
• Error codes related to water intake issues

This OEM LG part is also compatible with Sears/Kenmore.

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

Restore stable, level support with this replacement leg assembly. The adjustable foot steadies the unit on uneven floors, reducing vibration and rattling while allowing precise leveling for proper alignment and smooth, reliable operation.

• Provides adjustable support at the base of the unit
• Helps keep the appliance level on uneven or sloped floors
• Reduces wobble, vibration, and rattling noises
• Promotes proper door alignment and closure
• Replaces stripped, cracked, or missing leg assemblies

• Disconnect power; shut off water supply if applicable
• Carefully tilt and support the appliance to access the leg area
• Unthread the old leg; hand-thread the new assembly to avoid cross-threading, then fine-adjust with a wrench
• Level front-to-back and side-to-side; confirm stability before use

The Detergent Box Assembly is an OEM replacement part for LG washing machines. This assembly is responsible for holding and dispensing detergent and other laundry additives during the wash cycle. It ensures that the correct amounts of detergent, bleach, and fabric softener are released at the appropriate times, contributing to effective cleaning and care of your clothes.

Over time, the detergent box assembly can become worn out or damaged due to continuous exposure to water and detergent. Buildup of detergent residues can clog the compartments, and the mechanical parts of the assembly can also degrade. 

Symptoms of a bad detergent box assembly include:

• The detergent, bleach, or fabric softener not dispensing properly
• Visible cracks, warping, or damage to the box
• Residues remaining in the compartments after a wash cycle
• Leaks from the detergent box area
• Error messages related to dispensing issues

This OEM LG part is also compatible with some Sears/Kenmore washing machine models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This part may be black or gray in color.

This cover cap is a small plug that snaps into an open hole on the washer's cabinet or panel. Replace a missing or damaged cap to restore a finished appearance and help keep dust, lint, and splashes out of the enclosure.

• Closes an unused hole on the appliance panel to maintain a sealed cabinet
• Helps keep debris and moisture from entering the machine
• Restores the clean, finished look of the unit
• Typical signs it's needed: missing cap, cracked or loose cap, or a visible open hole on the panel

• Disconnect power and water supply before servicing the appliance
• Align the cap with the hole and press straight in until fully seated
• No tools are typically required; avoid prying on painted surfaces
• Do not block any ventilation or drain openings—install only in the designated capped hole

Includes sensor probe

The Dispenser Inlet Hose is an OEM part for LG washing machines. This hose directs water from the water inlet valve to the detergent dispenser, ensuring that water mixes with the detergent before entering the drum for efficient washing. The hose is designed to withstand high water pressure and temperature fluctuations.

Over time, the dispenser inlet hose can become clogged, cracked, or worn out due to regular use. Causes of a bad inlet hose include mineral deposits or debris buildup, wear and tear, and exposure to high temperatures or pressure that can cause the hose to degrade.

Symptoms of a bad dispenser inlet hose include:

• Leaking water around the detergent dispenser area
• Reduced water flow into the dispenser
• Visible cracks or wear on the hose
• Incomplete dissolution of detergent during wash cycles

This OEM LG part is also compatible with Sears/Kenmore.

The Dispenser Inlet Hose is an OEM part for LG washing machines. This hose directs water from the water inlet valve to the detergent dispenser, ensuring that water mixes with the detergent before entering the drum for efficient washing. The hose is designed to withstand high water pressure and temperature fluctuations.

Over time, the dispenser inlet hose can become clogged, cracked, or worn out due to regular use. Causes of a bad inlet hose include mineral deposits or debris buildup, wear and tear, and exposure to high temperatures or pressure that can cause the hose to degrade.

Symptoms of a bad dispenser inlet hose include:

• Leaking water around the detergent dispenser area
• Reduced water flow into the dispenser
• Visible cracks or wear on the hose
• Incomplete dissolution of detergent during wash cycles

This OEM LG part is also compatible with Sears/Kenmore.

This replacement connector hose routes water between the refrigerator water valve and the dispenser or ice maker, restoring reliable water flow and helping prevent leaks. It's a direct-fit service part used where the factory hose is worn or damaged. What it does

• Connects the refrigerator water valve to the dispenser or ice maker, providing a sealed water path.
• Restores proper water and ice delivery when a cracked or leaking hose causes reduced flow or pooling.
• Helps prevent leaks by replacing brittle, cracked, or split tubing and fittings.
• Works with the original fittings and routing used by the manufacturer for a secure connection.

• One replacement connector hose.

• Turn off and disconnect the refrigerator's water supply and power before starting.
• Verify orientation and routing match the original hose; avoid sharp bends or kinks.
• Tighten fittings securely but avoid over-tightening; inspect for leaks after reconnecting water.

The Drain Pump and Motor is an original LG (OEM) replacement part for LG made washing machines that is responsible for removing water from the washer at the end of the wash cycle. The pump forces water out through the drain hose so that clothing comes out free of excess water, making the drying process faster. 

Symptoms of a failing Drain Pump Motor include:

• Water not draining out of the washing machine 
• Noisy or unusual sounds coming from the pump area during the drain cycle
• The washing machine stopping mid-cycle

Causes of a bad Drain Pump Motor can range from obstructions in the pump or hose, which can strain or damage the motor, to wear and tear from regular use leading to motor failure. Electrical issues can also affect the motor's performance, preventing it from operating correctly.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Pump Casing is an OEM replacement part for LG top-load washing machines. This casing houses the water pump, providing a protective enclosure that shields the pump from debris and external factors. The casing is designed to fit snugly around the pump, helping to maintain its position and function within the washing machine.

Causes of casing failure can include cracks or leaks from repetitive pressure fluctuations exerted during machine operation. Casings experience extensive mechanical stresses.

Symptoms of a compromised casing include:

• Water leaks near or below the pump assembly
• Noisy or grinding pump noises during water fills or drainage
• Error codes related to water flow issues

This casing fits LG top load models as well as some Kenmore configurations. 

The Washer Circulation Pump Motor is an OEM replacement part for LG washing machines. It is a vital component responsible for circulating and pumping water through the wash tub during the various wash and rinse cycles.

Symptoms of a faulty circulation pump motor include:

• Improper water circulation or agitation during wash cycles
• Failure to drain or drain slowly after wash cycles
• Abnormal noises or vibrations coming from the pump area

Causes of a bad circulation pump motor can range from normal wear and tear over time, electrical malfunctions, blockages or obstructions in the pump impeller, or physical damage from foreign objects or debris.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

The Pump Filter Assembly is an OEM replacement part for LG washing machines. It is a crucial component that filters out lint, debris, and other particles from the wash water, preventing them from recirculating and damaging the pump or other internal components.

Symptoms of a need to replace the pump filter assembly:

• Clogging or blockages, leading to poor drainage or water not draining completely
• Excessive buildup of lint, hair, or other debris in the filter screen
• Leaks or water seeping from the filter housing or surrounding area
•  Unusual noises or vibrations during the drain or spin cycles, indicating a potential blockage

Causes of a faulty pump filter assembly can include excessive lint accumulation, damage to the filter screen or housing due to impact or mishandling, and general wear and tear over time.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

The Damper is an OEM replacement part for LG washing machines. It plays an important role in regulating airflow through the machine's drying system. The damper uses adjustable louvers to direct warm air emitted during the drying cycle. 

Causes of a faulty washer damper include broken internal mechanisms preventing louver movement, and restricting optimal air dispersion. Dust or mineral buildup can also impact function over time.

Symptoms of a problematic damper are

• incomplete or lengthy drying cycles.
• Clothing may still feel damp even after an extended run
• Excessive lint accumulation could also point to improper air management

This OEM LG part is also compatible with Sears/Kenmore.

The Stator Assembly is an OEM replacement part for LG washing machines. It is an electrical component inside the motor that converts rotational motion to electrical energy to power spinning motions.  Note: For the RPS or Hall Sensor, order part number AP7015078.

Symptoms of a faulty stator include:

• Slow or inefficient spinning, rubbing noises  
• The machine failing to fully drain or spin clothes
• Repeated blowouts or failure of related motor components

Causes can be wear and tear over extended use. Environmental factors like dust and moisture exposure may degrade insulation integrity. 

This OEM stator is also compatible with some Kenmore front-load washer models.

This is the direct-drive rotor for the dishwasher wash motor. It pairs with the stator to spin the impeller and circulate wash water through the spray arms, helping restore proper spray pressure and quieter operation when the original rotor is worn.

• Couples with the stator to drive the circulation pump impeller
• Moves wash water through the spray arms for consistent cleaning performance
• Common failure signs: little or no spray, poor cleaning, loud humming or grinding from the pump area, or intermittent wash action
• Physical damage or weakened magnets can prevent proper rotation

• Disconnect power and water supply and pull the unit forward for access
• Remove the toe-kick and drain remaining water at the sump
• Remove the pump cover and center fastener, then pull the old rotor straight off
• Seat the new rotor fully, reassemble, and run a test cycle to check operation and leaks

This water level pressure switch senses the washer tub's water level and signals the control to start or stop filling. It restores accurate fill detection for proper wash cycles and helps prevent overfilling or improper operation. What it does:

• Detects water level via a vacuum hose and tells the control board when to stop filling
• Helps prevent overfill, underfill, and related cycle interruptions
• Can resolve symptoms like washer not filling, overfilling, or stopping mid-cycle
• Works as the sensing interface between the tub and the control system

• One water level pressure switch assembly

• Disconnect power and shut off water supply before replacing the part
• Note the vacuum hose routing and electrical connector locations before removal
• Handle the small vacuum hose and plastic fittings gently to avoid damage or air leaks

The Suspension Spring is an OEM part for LG washing machines, specifically designed to support the tub assembly and maintain its stability during the wash and spin cycles. This spring plays a critical role in absorbing vibrations and reducing the amount of movement transferred to the washing machine's frame, ensuring smooth and quiet operation. 

Causes for a Suspension Spring to fail include normal wear and tear from repeated use, overloading the washing machine beyond its capacity, which can stretch or stress the springs, and corrosion from exposure to moisture and laundry detergents. 

Symptoms of a bad Suspension Spring include:

• Increased vibration and noise during the spin cycle.
• The washing machine "walking" or moving from its original position.
• Uneven drum movement, leading to inconsistent washing and spinning.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Suspension Spring Holder is an OEM part for LG washing machines. This holder supports the suspension springs that help stabilize the washer drum during operation, reducing vibration and movement. It plays a critical role in ensuring smooth and quiet operation of the washing machine.

Over time, the suspension spring holder can become worn or damaged due to regular use, heavy loads, or accidental impacts. Causes of a bad suspension spring holder include wear and tear, physical damage, or corrosion from moisture exposure.

Symptoms of a bad suspension spring holder include:

• Excessive vibration or shaking during wash cycles
• Unusual noises, such as banging or clunking
• The washer drum appearing misaligned or sagging
• The washing machine moving or walking during operation

This OEM LG part is also compatible with Sears/Kenmore.

This power cord assembly restores a secure electrical connection to your appliance so it can safely receive power. It replaces a worn, damaged, or faulty cord to help prevent interruptions and poor contact during normal use. What it does:

• Re-establishes the appliance's main power connection for reliable operation
• Replaces frayed, burnt, or damaged cord insulation and terminals
• Can stop intermittent power loss, sparking, or poor contact at the cord connection
• Provides the correct OEM-fit electrical cord and connector interface

• Always disconnect power at the breaker or unplug the appliance before starting work.
• Tighten terminal screws securely and avoid pinching or kinking the cord.

The Drain Hose Assembly is an OEM part for LG washing machines. It is a component designed to transport used water from the washer to the drain. This flexible hose assembly ensures that water flows smoothly out of your washing machine after each cycle, preventing leaks and maintaining the efficiency of your appliance. 

Causes for replacement can include wear and tear over time, clogs from lint or small items, kinks that restrict water flow, or damage from moving or improper installation. 

Symptoms of a bad Drain Hose Assembly include:

• Water leaking from the back or bottom of the washing machine
• Difficulty draining water out of the washer
• Puddles of water forming around the appliance during or after operation

This OEM LG part is also compatible with some Kenmore models.

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

The Door Switch is an OEM part for LG washing machines. It is responsible for detecting whether the washer door is securely closed or open. The door switch ensures that the washer operates only when the door is properly closed and latched.

A bad washer door switch can occur due to wear and tear over time, electrical malfunctions, or physical damage. If the door switch fails, it can prevent the washer from starting or cause it to stop mid-cycle, resulting in inconvenience and disruption to your laundry routine.

Symptoms of a bad washer door switch include:

• Washer not starting or powering on.
• Washer not completing cycles or stopping abruptly.
• Inability to lock or unlock the washer door.

This OEM LG part can also be used on Kenmore/Sears appliances.

This clamp assembly secures a hose or tubing connection to maintain a watertight seal and reduce vibration. Replacing a worn or damaged clamp helps stop leaks and prevents hoses from slipping loose during operation. What it does:

• Holds a hose or tube firmly in place to maintain proper sealing at the connection point.
• Prevents leaks caused by loose, cracked or corroded clamps.
• Reduces vibration and rattling from unsecured hoses.
• Common symptom: visible leaking, water pooling, or a loose hose connection.

• Disconnect power and shut off water supply before starting any repair.
• Use the correct pliers or screwdriver for the clamp type; avoid damaging the hose.
• Inspect the mating hose and seal; replace any cracked or hardened hoses before reinstalling.
• Do not overtighten—tighten just enough to secure the hose without cutting or deforming it.

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This noise filter assembly conditions incoming AC power to reduce electromagnetic interference before it reaches the control system. A failed line filter can cause no power, intermittent shutdowns, or breaker trips; replacing restores stable, reliable operation. What it does:

• Filters EMI/RFI on the power line to help protect sensitive control electronics
• Helps prevent interference that can cause no power, flickering display, or random resets
• A failing filter may trip a breaker/GFCI when the unit is plugged in or starts a cycle
• Visual clues can include scorch marks, burnt odor, or a cracked/bulged filter body

• 1 noise filter assembly

• Disconnect power before servicing; verify the outlet is de-energized
• Access is typically near the power cord entry behind a rear/top panel (varies by model)
• Label or photograph wire positions and transfer connections one by one; secure the ground
• Mount firmly and route wires to avoid pinching; reassemble and test for proper operation

• Line filter, EMI filter, RFI filter

This washer clutch assembly engages the drive system to shift between wash and spin modes. Replacing a worn clutch restores smooth agitation and full-speed spin performance, reducing noise and leaving clothes properly wrung out at cycle end.

• Engages and disengages the drive to transition between wash/agitate and spin
• Transfers motor torque to the basket during wash and spin
• Worn clutch can cause weak or no spin
• May result in no agitation or intermittent shifting
• Can cause grinding/scraping noises and leave clothes wet after the final spin

• Unplug the appliance and shut off water before starting
• Access from the bottom; support the washer securely to prevent tipping
• Remove obstructing drive components to reach the clutch; note hardware/wire routing for reassembly
• After installation, rotate the basket by hand and run a quick test cycle to confirm proper operation

The Inner Door Boot Seal Clamp is an OEM part for LG washing machines. The clamp's primary function is to secure the door boot seal in place, preventing leaks during the wash cycle. 

Causes of a bad Inner Door Boot Seal Clamp can include corrosion due to exposure to moisture and detergent, loss of tension over time, or physical damage which can lead to a compromised seal.

Symptoms of a bad Inner Door Boot Seal Clamp include:

• Water leaking from the front of the washing machine
• Visible rust or damage on the clamp
• The door boot seal coming loose or falling off

This genuine LG OEM replacement part is also compatible with some Kenmore models. 

This inlet hose delivers water from your home's supply to the appliance, restoring proper fill and water flow. It replaces a damaged, cracked, or leaking inlet line to help stop leaks and restore normal filling. What it does:

• Guides incoming water from the household supply to the appliance's fill system
• Replaces hoses that are cracked, split, or leaking at connections
• Helps resolve slow or no-fill symptoms caused by a damaged supply line
• Restores a secure connection at the appliance inlet to prevent water damage

• Turn off the water supply and unplug the appliance before starting
• Inspect fittings and seals; replace washers if worn to ensure a tight seal
• Hand-start threaded fittings, then snug with a wrench—avoid over-tightening
• Check for leaks after reconnecting water and restoring power

The Washing Machine Shock Absorber Kit is an OEM part for LG washing machines. This kit includes a shock absorber designed to reduce vibrations and absorb shocks during the wash cycle, providing stability and minimizing excessive movement. 

Over time, the shock absorbers can wear out due to regular use, exposure to heavy or unbalanced loads, or damage from impact. These factors can lead to reduced effectiveness of the shock absorbers, causing increased vibrations and noise.

Symptoms of a bad shock absorber kit include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or thumping noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

This OEM LG part is also compatible with Sears/Kenmore.

The Hinge Pin is an OEM part for LG washing machines. It serves as a pivot point for the washer door, allowing it to open and close smoothly. This component is crucial for maintaining the proper alignment and function of the washer door, ensuring a secure and reliable seal during operation.

Common causes of a bad hinge pin include frequent use leading to wear and tear, physical damage from accidental impacts, or rust and corrosion over time. A compromised hinge pin can result in misalignment of the door, affecting the washing machine's ability to close properly and maintain an effective seal.

Symptoms of a bad hinge pin include:

• Difficulty opening or closing the washer door
• Door not staying securely closed during operation
• Squeaking or grinding noises when the door is moved
• Visible wear or damage to the hinge pin

This OEM LG part is also compatible with Sears/Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.