Need Help?
Call or text
Heat-resistant fiberglass gasket seals your oven door perimeter to maintain consistent temperatures. Replace when worn, frayed, or flattened to restore efficiency. Verify fit by model number.
Creates a watertight seal between the washer door and tub. Replace if you notice leaks, tears, or mold buildup. Confirm fit with your model number.
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
Seals the water injector connection in your washer to prevent leaks and frost buildup. Replace if you notice water leaking or moisture around the inlet area. Confirm fit with your model number.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Felt seal that fits around your dishwasher's door vent to contain steam and moisture. Replace if you notice condensation or minor leaks during cycles.
Replaced the felt seal and door vent assembly by removing the inside panel of the door and cleaning off the old seal and replacing with the new one. The vent assembly simply snapped out and was easy to replace with the new one. No more leaks and Mother was happy. Removal of the screws required a torx screw driver and someone to hold the door open while the panel was replaced. Easy fix. Read more
Replace your washer's door boot seal when you notice leaks, tears, or mold around the door opening. Creates a watertight barrier. Confirm fit with your model.
Replaced the seal. Read more
Black door boot seal creates a watertight barrier between the door and tub on front-load washers. Replace when worn or torn to stop leaks. Verify fit.
Creates a watertight seal between the washer tub and cabinet. Replace if you notice water leaking during wash cycles. Verify fit with your model number.
Disassembled washer, found that 2 out of the 3 basket support legs had cracked through. Unfortunately, support cannot be bought except as an assembly, so had to spend almost $300 for the part. Bearings were worn, but not trashed, so I replaced them and the seal. Note, most parts places (including AppliancePartsPros.com) will only sell the bearings and seal as part of the rear tub assembly. The bearings are standard 6205 and 6206 sealed ball bearings, available from Grainger and many others for... Read more
Inlet hose strainer and washer kit for washers. Replace if you notice leaks at hose connections or reduced water flow. Confirm fit with your model.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
Flexible rubber seal around the door opening that prevents leaks during wash and spin cycles. Replace if torn, cracked, or moldy. Confirm fit with your washer model number.
Seals the door opening to the outer tub on front-load washers. Replace if you notice leaks, tears, odors, or clothes snagging. Confirm fit with your model.
Followed online instructions. Read more
Seals the outer tub to prevent leaks during spin and drain cycles. Replace if washer leaks from the center or bottom. Confirm fit with your model number.
Outer basket had a lot of rust on the lip at the top of the basket, I ordered tub gasket, but when I removed the old gasket, some of the lip broke off, leaving gaps at the top, went to the hardware store, and purchased thin sheet of 8x10" aluminum, cut and shaped pieces from this sheet, to fit under the damaged lip, to bridge the gaps, rounded edges to fit against the rounded part of the outer tub, under the lip, once shaped, I glued them in place with emblem adhesive, did this all the way... Read more
Replace your washer door gasket to restore the watertight seal and prevent leaks. Install when you notice water escaping or mildew buildup around the door.
Replace your washer tub seal to stop leaks between inner and outer tubs. Install when you notice water pooling or moisture around the drum. Verify fit.
Rubber gasket that seals the joint between the tub and cover to prevent leaks and water seepage. Replace if you notice leaking or debris buildup. Verify fit.
Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more
Prevents water leaks between the washer tub and pump. Replace if you notice water pooling under your machine or leaking during cycles. Verify fit with your model.